EN 14127:2011
(Main)Non-destructive testing - Ultrasonic thickness measurement
Non-destructive testing - Ultrasonic thickness measurement
This European Standard specifies the principles for ultrasonic thickness measurement of metallic and non-metallic materials by direct contact, based on measurement of time-of-flight of ultrasonic pulses only.
Zerstörungsfreie Prüfung - Dickenmessung mit Ultraschall
Dieses Dokument legt die Grundlagen fest zur Ermittlung der Dicke metallischer und nicht metallischer Werkstoffe mit Ultraschall durch unmittelbaren Kontakt mit dem Prüfgegenstand allein, basierend auf der Messung der Laufzeit von Ultraschallimpulsen.
Essais non destructifs - Mesurage de l'épaisseur par ultrasons
La présente Norme européenne spécifie les principes pour le mesurage de l’épaisseur par ultrasons de
matériaux métalliques et non métalliques par contact direct, exclusivement basés sur la mesure du temps de
vol d’impulsions ultrasonores.
Neporušitveno preskušanje - Ultrazvočno merjenje debeline
Ta dokument določa načela ultrazvočnega merjenja debeline kovinskih in nekovinskih materialov z neposrednim stikom, zasnovanim samo na meritvah časa potovanja ultrazvočnih pulzov.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zerstörungsfreie Prüfung - Dickenmessung mit UltraschallEssais non destructifs - Mesurage de l'épaisseur par ultrasonsNon-destructive testing - Ultrasonic thickness measurement19.100Neporušitveno preskušanjeNon-destructive testingICS:Ta slovenski standard je istoveten z:EN 14127:2011SIST EN 14127:2011en,fr,de01-julij-2011SIST EN 14127:2011SLOVENSKI
STANDARD
SIST EN 14127:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14127
February 2011 ICS 19.100 Supersedes EN 14127:2004English Version
Non-destructive testing - Ultrasonic thickness measurement
Essais non destructifs - Mesurage de l'épaisseur par ultrasons
Zerstörungsfreie Prüfung - Dickenmessung mit UltraschallThis European Standard was approved by CEN on 25 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14127:2011: ESIST EN 14127:2011
EN 14127:2011 (E) 2 Contents Page Foreword . 41Scope . 52Normative references . 53Terms and definitions . 54Measurement modes . 55General requirements . 75.1Instruments . 75.2Probes . 75.3Couplant . 75.4Reference blocks . 75.5Test objects . 75.6Qualification of personnel . 86Application of the technique . 86.1Surface conditions and surface preparation . 86.2Technique . 86.2.1General . 86.2.2Measurement during manufacture . 96.2.3In-service measurement of residual wall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.