EN ISO 22476-10:2017
(Main)Geotechnical investigation and testing - Field testing - Part 10: Weight sounding test (ISO 22476-10:2017)
Geotechnical investigation and testing - Field testing - Part 10: Weight sounding test (ISO 22476-10:2017)
ISO 22476-10 specifies the equipment, execution and reporting requirements of the weight sounding test.
NOTE ISO 22476-10 fulfils the requirements for the weight sounding test as part of the geotechnical investigation and testing according to EN 1997?1 and EN 1997?2.
ISO 22476-10 specifies the procedure for conducting a test with the weight sounding device in natural soils, made ground, and fill either on land or on water. ISO 22476-10 is applicable to the determination of the resistance of soil to the static load or the static load and the specified turning of the sounding point.
ISO 22476-10 gives guidelines for the use of the weight sounding test to give a continuous soil profile and an indication of the layer sequence. The use includes the estimation of the density of cohesionless soils and the depth to very dense ground layers indicating the length of end-bearing piles.
Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 10: Gewichtssondierung (ISO 22476-10:2017)
Dieses Dokument legt die Anforderungen an die Geräte, die Durchführung und die Berichtserstellung für die Gewichtssondierung fest.
ANMERKUNG Dieses Dokument erfüllt die Anforderungen an Gewichtssondierungen im Rahmen der geotechnischen Untersuchung und Prüfung nach EN 1997-1 und EN 1997-2.
Dieses Dokument legt das Verfahren zur Durchführung eines Versuchs mittels Gewichtssondierung in natürlichen Böden und in Auffüllungen an Land oder auf dem Wasser fest. Dieses Dokument gilt für die Bestimmung des Bodenwiderstands gegen das statische oder das statische und drehende Eindringen der Sondenspitze.
Dieses Dokument gibt einen Leitfaden zur Anwendung der Gewichtssondierung, um ein fortlaufendes Bodenprofil und Hinweise auf die Schichtenfolge zu erhalten. Die Gewichtssondierung wird auch dazu verwendet, die Dichte von nichtbindigen Böden und die Tiefe sehr dicht gelagerter Bodenschichten festzustellen, zur Festlegung der Länge von Spitzendruckpfählen.
Reconnaissance et essais géotechniques - Essais en place - Partie 10: Essai de sondage par poids (ISO 22476-10:2017)
La présent document traite des exigences relatives à l'appareillage, à l'exécution et au compte rendu de l'essai de sondage par poids.
NOTE Le présent document satisfait aux exigences applicables aux essais de sondage par poids dans le cadre de la reconnaissance et des essais géotechniques selon EN 1997-1 et EN 1997-2.
Le présent document décrit la procédure d'essai employant un dispositif de sondage par poids dans les sols naturels, les terrains rapportés et les remblais sur terre ou sur étendue d'eau. L'essai de sondage par poids est réalisé en faisant pénétrer la pointe du dispositif de sondage par poids dans le sol. Le document traite de la détermination de la résistance du sol à la charge statique, ou à l'association de la charge statique et de la rotation spécifiée de la pointe de sondage.
Le présent document donne des lignes directrices sur l'utilisation de l'essai de sondage par poids pour obtenir un profil de sol continu et une indication de la séquence des couches. L'essai de sondage par poids est également employé pour estimer la masse volumique des sols sans cohésion et pour estimer la profondeur des couches très denses indiquant la longueur des pieux travaillant en pointe.
Geotehnično preiskovanje in preskušanje - Preskušanje na terenu - 10. del: Težnostni sondirni preskus (ISO 22476-10:2017)
Standard vključuje zahteve za raziskovanje tal s težnostnim sondirnim preskusom (WST) kot delom geotehničnega raziskovanja v skladu s standardoma EN 1997-1 in EN 1997-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2018
1DGRPHãþD
SIST-TS CEN ISO/TS 22476-10:2008
*HRWHKQLþQRSUHLVNRYDQMHLQSUHVNXãDQMH3UHVNXãDQMHQDWHUHQXGHO
7HåQRVWQLVRQGLUQLSUHVNXV ,62
Geotechnical investigation and testing - Field testing - Part 10: Weight sounding test
(ISO 22476-10:2017)
Geotechnische Erkundung und Untersuchung - Felduntersuchungen - Teil 10:
Gewichtssondierung (ISO 22476-10:2017)
Reconnaissance et essais géotechniques - Essais en place - Partie 10: Essai de
sondage par poids (ISO 22476-10:2017)
Ta slovenski standard je istoveten z: EN ISO 22476-10:2017
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 22476-10
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 93.020 Supersedes CEN ISO/TS 22476-10:2005
English Version
Geotechnical investigation and testing - Field testing - Part
10: Weight sounding test (ISO 22476-10:2017)
Reconnaissance et essais géotechniques - Essais en Geotechnische Erkundung und Untersuchung -
place - Partie 10: Essai de sondage par poids (ISO Felduntersuchungen - Teil 10: Gewichtssondierung
22476-10:2017) (ISO 22476-10:2017)
This European Standard was approved by CEN on 8 August 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22476-10:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 22476-10:2017) has been prepared by Technical Committee ISO/TC 182
“Geotechnics” in collaboration with Technical Committee CEN/TC 341 “Geotechnical Investigation and
Testing” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018 and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 22476-10:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22476-10:2017 has been approved by CEN as EN ISO 22476-10:2017 without any
modification.
INTERNATIONAL ISO
STANDARD 22476-10
First edition
2017-10
Geotechnical investigation and
testing — Field testing —
Part 10:
Weight sounding test
Reconnaissance et essais géotechniques — Essais en place —
Partie 10: Essai de sondage par poids
Reference number
ISO 22476-10:2017(E)
©
ISO 2017
ISO 22476-10:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 22476-10:2017(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Equipment . 2
5 Test procedure . 4
5.1 Calibration and checks . 4
5.2 Use of predrilling and casing . 4
5.3 Manual weight sounding . 4
5.4 Mechanized weight sounding . 5
5.5 Safety requirements . 5
6 Test results . 5
7 Report . 6
7.1 Field report . 6
7.2 Test report . 7
Bibliography . 8
ISO 22476-10:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
ISO 22476-10 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 341, Geotechnical investigation and testing, in collaboration with ISO Technical Committee
ISO/TC 182, Geotechnics, in accordance with the Agreement on technical cooperation between ISO and
CEN (Vienna Agreement).
This first edition of ISO 22476-10 cancels and replaces ISO/TS 22476-10:2005, which has been
technically revised.
A list of all parts in the ISO 22476 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved
INTERNATIONAL STANDARD ISO 22476-10:2017(E)
Geotechnical investigation and testing — Field testing —
Part 10:
Weight sounding test
1 Scope
This document specifies the equipment, execution and reporting requirements of the weight
sounding test.
NOTE This document fulfils the requirements for the weight sounding test as part of the geotechnical
investigation and testing according to EN 1997–1 and EN 1997–2.
This document specifies the procedure for conducting a test with the weight sounding device in natural
soils, made ground, and fill either on land or on water. This document is applicable to the determination
of the resistance of soil to the static load or the static load and the specified turning of the sounding point.
This document gives guidelines for the use of the weight sounding test to give a continuous soil profile
and an indication of the layer sequence. The use includes the estimation of the density of cohesionless
soils and the depth to very dense ground layers indicating the length of end-bearing piles.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 14688 (all parts), Geotechnical investigation and testing — Identification and classification of soil
ISO 14689-1, Geotechnical investigation and testing — Identification and classification of rock — Part 1:
Identification and description
ISO 22475-1, Geotechnical investigation and testing — Sampling methods and groundwater
measurements — Part 1: Technical principles for execution
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 22475-1 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http://www.electropedia.org/
— ISO Online browsing platform: available at http://www.iso.org/obp
3.1
weight sounding resistance
smallest standard load for which the penetrometer sinks without rotation, or the number of half turns
per 0,20 m of penetration when the penetrometer has its maximum load and is rotated
ISO 22476-10:2017(E)
3.2
manual weight sounding test
test made by loading and rotating the penetrometer by hand using a handle
Note 1 to entry: The penetrometer is loaded by weights.
3.3
m
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.