EN ISO 17672:2010

Brazing - Filler metals (ISO 17672:2010)

ISO 17672:2010 specifies the compositional ranges of a series of filler metals used for brazing. The filler metals are divided into seven classes, related to their composition, but not necessarily to the major element present.
In the case of composite products, such as flux-coated rods, pastes or plastics tapes, ISO 17672:2010 covers only the filler metal that forms part of such products.

Hartlöten - Lote (ISO 17672:2010)

Diese Internationale Norm legt die Zusammensetzungen von Loten fest, die zum Hartlöten verwendet werden.
Diese Lote sind entsprechend ihrer Zusammensetzung, aber nicht notwendigerweise nach dem vorhandenen
Hauptlegierungselement, in sieben Gruppen aufgeteilt.
ANMERKUNG 1 Für die Hauptlegierungselemente, siehe Anhang A.
Diese Internationale Norm gilt nicht für Produkte wie z. B. flussmittelummantelte Lotstäbe, Lotpasten
oder -bänder, sondern nur für den Lotanteil solcher Produkte. Obwohl in den Tabellen die Schmelzbereiche mit
angegeben werden, können diese, entsprechend der erlaubten Bandbreite der Zusammensetzung von Loten
variieren und gelten nur als Näherungswerte. Deshalb dienen diese Angaben nur zur Information. Die
technischen Lieferbedingungen gelten für Lote zum Hartlöten und für Produkte, die Hartlote mit anderen
Bestandteilen wie Flussmittel und/oder Umhüllung enthalten.
ANMERKUNG 2 Für einige Anwendungen, z. B. Schmuckverarbeitung, Luft- und Raumfahrt und Zahntechnik, können
andere Lote als die, die in dieser Norm enthalten sind, verwendet werden. Diese Lote sind in anderen Internationalen
Normen enthalten, auf die Bezug genommen werden kann.

Brasage fort - Métaux d’apport (ISO 17672:2010)

L'ISO 17672:2010 spécifie les gammes de composition de métaux d'apport utilisés pour le brasage fort. Les métaux d'apport ont été divisés en sept classes, d'après leur composition, mais pas nécessairement d'après leur élément majeur.
En ce qui concerne les produits composites, tels que les baguettes de brasage enrobées, les pâtes ou les rubans plastiques, l'ISO 17672:2010 ne couvre que le métal d'apport faisant partie intégrante de tels produits.

Trdo spajkanje - Dodajni materiali (ISO 17672:2010)

Ta mednarodni standard določa razpone sestave vrste dodajnih materialov, ki se uporabljajo za trdo spajkanje. Dodajni materiali so glede na sestavo, a ne nujno glede na glavni prisotni element, razdeljeni v sedem razredov.

General Information

• Status: Withdrawn
• Publication Date: 31-May-2010
• Withdrawal Date: 27-Sep-2016
• ICS: 25.160.50 - Brazing and soldering
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 20 - Brazing
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 28-Sep-2016
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN ISO 17672:2011 - Brazing - Filler metals (ISO 17672:2010)

Relations

• Replaces: EN 1044:1999 - Brazing - Filler metals
• Effective Date: 08-Jun-2010
• Replaced By: EN ISO 17672:2016 - Brazing - Filler metals (ISO 17672:2016)
• Effective Date: 05-Jun-2013

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17672:2011
01-november-2011
1DGRPHãþD
SIST EN 1044:2001
Trdo spajkanje - Dodajni materiali (ISO 17672:2010)
Brazing - Filler metals (ISO 17672:2010)
Hartlöten - Lötzusätze (ISO 17672:2010)
Brasage fort - Métaux d'apport (ISO 17672:2010)
Ta slovenski standard je istoveten z: EN ISO 17672:2010
ICS:
25.160.50 Trdo in mehko lotanje Brazing and soldering
SIST EN ISO 17672:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 17672:2011

---------------------- Page: 2 ----------------------

SIST EN ISO 17672:2011


EUROPEAN STANDARD
EN ISO 17672

NORME EUROPÉENNE

EUROPÄISCHE NORM
June 2010
ICS 25.160.50 Supersedes EN 1044:1999
English Version
Brazing - Filler metals (ISO 17672:2010)
Brasage fort - Métaux d’apport (ISO 17672:2010) Hartlöten - Lote (ISO 17672:2010)
This European Standard was approved by CEN on 12 May 2010.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.






EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17672:2010: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 17672:2011
EN ISO 17672:2010 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 17672:2011
EN ISO 17672:2010 (E)
Foreword
This document (EN ISO 17672:2010) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn
at the latest by December 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 1044:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 17672:2010 has been approved by CEN as a EN ISO 17672:2010 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 17672:2011

---------------------- Page: 6 ----------------------

SIST EN ISO 17672:2011

INTERNATIONAL ISO
STANDARD 17672
First edition
2010-06-01


Brazing — Filler metals
Brasage fort — Métaux d'apport





Reference number
ISO 17672:2010(E)
©
ISO 2010

---------------------- Page: 7 ----------------------

SIST EN ISO 17672:2011
ISO 17672:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in thi
...