EN 13445-8:2006
(Main)Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
This Part 8 of this European Standard specifies requirements for unfired pressure vessels and their parts made of aluminium and aluminium alloys in addition to the general requirements for unfired pressure ves-sels under EN 13445:2002 Parts 1 to 5. This European Standard specifies unfired pressure vessels for loads up to 500 full cycles.
NOTE Cast materials are not included in this version. Details regarding cast materials will be subject to an amendment to or a revision of this European Standard.
Unbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und Aluminiumlegierungen
Dieser Teil 8 der Europäischen Norm legt zusätzlich zu den allgemeinen Anforderungen an unbefeuerte
Druckbehälter nach EN 13445:2002, Teile 1 bis 5, Anforderungen an aus Aluminium und Aluminiumlegie-rungen
hergestellte unbefeuerte Druckbehälter und deren Bauteile fest. Diese Europäische Norm gilt für unbe-feuerte
Druckbehälter für Druckbelastungen bis zu 500 vollen Lastzyklen.
ANMERKUNG Gusswerkstoffe sind in der vorliegenden Fassung nicht enthalten. Angaben zu Gusswerkstoffen werden
in einer Ergänzung bzw. Überarbeitung dieser Europäischer Norm aufgenommen.
Récipients sous pression non soumis à la flamme - Partie 8 : Exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminium
La présente partie 8 de cette norme européenne spécifie les exigences relatives aux récipients sous pression non
soumis à la flamme et à leurs composants en aluminium et alliages d’aluminium, en complément des exigences
générales énoncées dans les parties 1 à 5 de l’EN 13445 :2002. La présente norme européenne concerne les
récipients sous pression non soumis à la flamme pouvant aller jusqu’à 500 cycles complets de chargement.
NOTE Les matériaux moulés ne sont pas inclus pour l’instant. Des détails relatifs aux matériaux moulés feront l’objet d’un
amendement ou à une révision de la présente norme européenne.
Neogrevane tlačne posode – 8. del: Dodatne zahteve za tlačne posode iz aluminija in aluminijevih zlitin
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloysRécipients sous pression non soumis a la flamme - Partie 8 : Exigences complémentaires pour les récipients sous pression en aluminium et alliages d'aluminiumUnbefeuerte Druckbehälter - Teil 8: Zusätzliche Anforderungen an Druckbehälter aus Aluminium und AluminiumlegierungenTa slovenski standard je istoveten z:EN 13445-8:2006SIST EN 13445-8:2007en23.020.30MHNOHQNHPressure vessels, gas cylindersICS:SLOVENSKI
STANDARDSIST EN 13445-8:200701-marec-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13445-8October 2006ICS 23.020.30 English VersionUnfired pressure vessels - Part 8: Additional requirements forpressure vessels of aluminium and aluminium alloysRécipients sous pression non soumis à la flamme - Partie 8: Exigences complémentaires pour les récipients souspression en aluminium et alliages d'aluminiumUnbefeuerte Druckbehälter - Teil 8: ZusätzlicheAnforderungen an Druckbehälter aus Aluminium undAluminiumlegierungenThis European Standard was approved by CEN on 14 July 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13445-8:2006: E
EN 13445-8:2006 (E) Issue 1 (2006-10) 2 Contents Page Foreword.4 1 Scope.5 2 Normative references.5 3 Terms, definitions, symbols and units.6 4 General requirements.6 5 Materials.6 5.1 General.6 5.2 Elongation after fracture.6 5.3 Prevention of brittle fracture.7 5.4 Lamellar tearing.7 5.5 Chemical composition.7 5.6 Material grouping system.7 6 Design.8 6.1 General.8 6.2 Design temperature and properties.8 6.3 Time-independent nominal design stress.9 6.4 Thick walled, small bore piping for sh
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.