EN 12807:2009
(Main)LPG equipment and accessories - Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) - Design and construction
LPG equipment and accessories - Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) - Design and construction
This European Standard specifies the minimum requirements for the design, construction and testing during manufacture of transportable refillable brazed steel Liquefied Petroleum Gas (LPG) cylinders, of water capacity from 0,5 l up to and including 15 l, exposed to ambient temperatures.
This European Standard applies only to cylinders having a circular cross-section without any longitudinal joint.
FlüssiggasGeräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) - Konstruktion und Herstellung
Diese Europäische Norm legt die Mindestanforderungen an die Konstruktion, die Herstellung und die während
der Herstellung erfolgende Prüfung ortsbeweglicher, wiederbefüllbarer, hartgelöteter Flaschen aus Stahl für
Flüssiggas (LPG) mit einem Fassungsraum von 0,5 l bis einschließlich 15 l fest, die Umgebungstemperaturen
ausgesetzt sind.
Die vorliegende Europäische Norm gilt nur für Flaschen mit kreisförmigem Querschnitt ohne Längsnaht.
Equipement et accessoires pour GPL - Bouteilles transportables et rechargeables en acier brasé pour gaz de pétrole liquéfié (GPL) - Conception et fabrication
La présente norme européenne définit les exigences minimales concernant la conception, la fabrication et les
essais lors de la fabrication des bouteilles transportables et rechargeables en acier brasé pour gaz de pétrole
liquéfiés (GPL), d’une capacité en eau comprise entre 0, 5 l et 15 l inclus et exposées aux températures
ambiantes.
La présente norme européenne s’applique exclusivement aux bouteilles à section circulaire ne comportant
pas de joints longitudinaux.
Oprema in pribor za utekočinjeni naftni plin (UNP) - Premične, ponovno polnljive, trdo spajkane jeklenke iz jekla za utekočinjeni naftni plin (UNP) - Konstruiranje in izdelava
Ta evropski standard določa minimalne zahteve za konstruiranje, izdelavo in preskušanje med proizvodnjo za premične, ponovno polnljive, trdo spajakane jeklenke iz jekla za utekočinjeni naftni plin (UNP), z vodno kapaciteto od 0,5 l do in vključno 15 l, izpostavljene temperaturam v prostoru. Ta evropski standard velja le za jeklenke, ki imajo krožni prerez brez kakršnega koli podolžnega spoja.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.L]GHODYDFlüssiggasGeräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare, hartgelötete Flaschen aus Stahl für Flüssiggas (LPG) - Konstruktion und HerstellungBouteilles transportables et rechargeables en acier brasé pour gaz de pétrole liquéfiés (GPL) - Conception et fabricationLPG equipment and accessories - Transportable refillable brazed steel cylinders for liquefied petroleum gas (LPG) - Design and construction23.020.30MHNOHQNHPressure vessels, gas cylindersICS:Ta slovenski standard je istoveten z:EN 12807:2009SIST EN 12807:2010en,fr,de01-december-2010SIST EN 12807:2010SLOVENSKI
STANDARDSIST EN 12807:20021DGRPHãþD
SIST EN 12807:2010
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12807June 2009ICS 23.020.30Supersedes EN 12807:2001
English VersionLPG equipment and accessories - Transportable refillablebrazed steel cylinders for liquefied petroleum gas (LPG) -Design and constructionEquipement et accessoires pour GPL - Bouteillestransportables et rechargeables en acier brasé pour gaz depétrole liquéfié (GPL) - Conception et fabricationFlüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche,wiederbefüllbare, hartgelötete Flaschen aus Stahl fürFlüssiggas (LPG) - Konstruktion und HerstellungThis European Standard was approved by CEN on 14 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12807:2009: ESIST EN 12807:2010
EN 12807:2009 (E) 2 Contents Page Foreword .4 Introduction .5 1 Scope .6 2 Normative references .6 3 Terms, definitions and symbols .6 3.1 Terms and definitions .6 3.2 Symbols .7 4 Materials .7 5 Design .9 5.1 General requirements .9 5.2 Calculation of cylindrical shell thickness . 10 5.3 Design of torispherical and semi-ellipsoidal ends concave to pressure. 10 5.4 Design of ends of shapes other than torispherical and semi-ellipsoidal . 14 5.5 Minimum wall thickness . 14 5.6 Design of openings. 15 5.7 Valve protection .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.