iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN ISO 13473-5

(Main)

Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO/DIS 13473-5:2024)

Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO/DIS 13473-5:2024)

ISO 13473-5:2009 specifies procedures for determining the average depth or level of pavement surface megatexture by measuring the profile curve of a surface and calculating megatexture descriptors from this profile. The technique is designed to give meaningful and accurate measurement and description of pavement megatexture characteristics for various purposes.
Since there is an overlap between megatexture and the surrounding ranges, the megatexture descriptors unavoidably have a certain correlation with corresponding measures in those ranges. ISO 13473-5:2009 specifies measurements and procedures which are in relevant parts compatible with those in ISO 13473-1, ISO 8608 and EN 13036-5.

Charakterisierung der Textur von Fahrbahnbelägen unter Verwendung von Oberflächenprofilen - Teil 5: Bestimmung der Megatextur (ISO/DIS 13473-5:2024)

Caractérisation de la texture d'un revêtement de chaussée à partir de relevés de profils de la surface - Partie 5: Détermination de la mégatexture (ISO/DIS 13473-5:2024)

L'ISO 13473-5:2009 spécifie des modes opératoires permettant de déterminer la profondeur moyenne ou le niveau de la mégatexture d'une surface de revêtement en mesurant la courbe du profil de cette surface et en calculant les descripteurs de mégatexture de ce profil. La technique a été élaborée pour donner une mesure et une description significatives et précises des caractéristiques de la mégatexture du revêtement pour différentes utilisations.
Du fait du recouvrement entre la mégatexture et les domaines voisins, les descripteurs de la mégatexture présentent inévitablement une certaine corrélation avec les mesures correspondantes de ces autres domaines. L'ISO 13473-5:2009 spécifie des mesurages et des modes opératoires qui sont dans leurs différents aspects aussi compatibles que possible avec ceux de l'ISO 13473-1, de l'ISO 8608 et de l'EN 13036-5.

Karakterizacija teksture vozišča z uporabo profilov površine - 5. del: Ugotavljanje megateksture (ISO/DIS 13473-5:2024)

General Information

Status
Not Published
Publication Date
11-May-2025
ICS
17.140.30 - Noise emitted by means of transport
93.080.20 - Road construction materials
Technical Committee
CEN/TC 227 - Road materials
Drafting Committee
CEN/TC 227/WG 5 - Surface characteristics
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
19-Nov-2024
Completion Date
19-Nov-2024
Ref Project
oSIST prEN ISO 13473-5:2024 - Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO/DIS 13473-5:2024)

Relations

Revises
EN ISO 13473-5:2009 - Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO 13473-5:2009)
Effective Date
30-Mar-2022

Buy Standard

prEN ISO 13473-5:2024prEN ISO 13473-5:2024
PreviousNext
Draft
prEN ISO 13473-5:2024
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-junij-2024
Karakterizacija teksture vozišča z uporabo profilov površine - 5. del: Ugotavljanje
megateksture (ISO/DIS 13473-5:2024)
Characterization of pavement texture by use of surface profiles - Part 5: Determination of
megatexture (ISO/DIS 13473-5:2024)
Charakterisierung der Textur von Fahrbahnbelägen unter Verwendung von
Oberflächenprofilen - Teil 5: Bestimmung der Megatextur (ISO/DIS 13473-5:2024)
Caractérisation de la texture d'un revêtement de chaussée à partir de relevés de profils
de la surface - Partie 5: Détermination de la mégatexture (ISO/DIS 13473-5:2024)
Ta slovenski standard je istoveten z: prEN ISO 13473-5
ICS:
17.140.30 Emisija hrupa transportnih Noise emitted by means of
sredstev transport
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 13473-5
ISO/TC 43/SC 1
Characterization of pavement
Secretariat: DIN
texture by use of surface profiles —
Voting begins on:
Part 5: 2024-04-11
Determination of megatexture
Voting terminates on:
2024-07-04
Caractérisation de la texture d'un revêtement de chaussée à
partir de relevés de profils de la surface —
Partie 5: Détermination de la mégatexture
ICS: 17.140.30; 93.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 13473-5:2024(en)
DRAFT
ISO/DIS 13473-5:2024(en)
International
Standard
ISO/DIS 13473-5
ISO/TC 43/SC 1
Characterization of pavement
Secretariat: DIN
texture by use of surface profiles —
Voting begins on:
Part 5:
Determination of megatexture
Voting terminates on:
Caractérisation de la texture d'un revêtement de chaussée à
partir de relevés de profils de la surface —
Partie 5: Détermination de la mégatexture
ICS: 17.140.30; 93.080.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 13473-5:2024(en)
ii
ISO/DIS 13473-5:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
3.1 General terms .2
3.2 Ranges of texture .3
3.3 Megatexture measurement method .5
4 Measurement instruments . 6
4.1 Instruments in general .6
4.1.1 Performance check .6
4.1.2 Indication of invalid readings (drop-outs) .6
5 Test surface considerations . 7
5.1 General .7
5.2 Test lengths.7
6 Measurement method . 8
6.1 General .8
6.2 Sensitivity to vertical motion of the vehicle .8
6.3 Calibration .8
6.4 Measuring speed .9
6.5 Measurement of the texture profile .9
7 Data processing . 9
7.1 General .9
7.2 Preprocessing: drop-out rate and validity of measurements.9
7.3 Resampling to a certain spatial resolution .10
7.4 Spike identification and reshaping the profile .11
7.5 Filtering of the profile .11
7.6 Calculation of RMS .11
Me
7.7 Averaging .11
7.8 Longitudinal standard deviation (informative) .11
7.9 Singularities . 12
8 Measurement uncertainty .12
9 Safety considerations during measurements . 14
10 Test report . 14
Annex A (normative) Spike removal procedure .16
Annex B (informative) Example of test report and graphical presentations . 19
Annex C (informative) Measurement uncertainty.24
Annex D (normative) Megatexture digital filters .27
Annex E (informative) Megatexture reference program code .29
Annex F (informative) Procedure for sampling of measurement sections if the whole area of
interest cannot be measured .30
Annex G (normative) Profile conditioning before filtering .33
Annex H (Informative) Guidelines for choosing a suitable Calculation Length .36
Bibliography .38

iii
ISO/DIS 13473-5:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent
rights identified during the development of the document will be in the Introduction and/or on the ISO list of
patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 11819-1:2023(Main)
Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 1: Statistical Pass-By method (ISO 11819-1:2023)
SIST EN ISO 11819-1:2023

This document specifies a method of comparing traffic noise on different road surfaces for various compositions of road traffic for the purpose of evaluating different road surface types. Sound levels representing either light or heavy vehicles at selected speeds are assigned to a certain road surface. The method is applicable to traffic travelling at constant speed, i.e. free-flowing conditions at posted speeds of 50 km/h and upwards. For conditions where traffic is not free flowing, such as at junctions and where the traffic is congested, the method is not applicable.
A standard method for comparing the noise characteristics of road surfaces gives road and environment authorities a tool for establishing common practices or limits regarding the use of road surfaces meeting certain noise criteria. However, it is not within the scope of ISO 11819 (all parts) to suggest such criteria.
The statistical pass-by (SPB) method is suitable for use for the following main purposes:
—    to classify road surfaces according to their influence on traffic noise (surface classification);
—    to assist in verifying conformity of production of road surfaces;
—    to evaluate acoustic performance of road surfaces throughout operation relative to new condition;
—    to evaluate the influence of different road surfaces on traffic noise at sites irrespective of condition and service time;
—    to evaluate acoustic performance of a road surface relative to a reference surface.
Due to practical restrictions, the method cannot be applied at all possible locations. However, the backing board method can allow some locations to be tested that were not previously acceptable.
Clause 5 gives a general description of the SPB method.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13473-1:2019(Main)
Characterization of pavement texture by use of surface profiles - Part 1: Determination of mean profile depth (ISO 13473-1:2019, Corrected version 2021-06)
SIST EN ISO 13473-1:2019

This document describes a test method to determine the average depth of pavement surface macrotexture (see Clause 3) by measuring the profile of a surface and calculating the texture depth from this profile. The technique is designed to provide an average depth value of only the pavement macrotexture and is considered insensitive to pavement microtexture and unevenness characteristics.
The objective of this document is to make available an internationally accepted procedure for determination of pavement surface texture depth which is an alternative to the traditionally used volumetric patch technique (generally using sand or glass beads), giving comparable texture depth values. To this end, this document describes filtering procedures that are designed to give the best possible representation of texture depths determined with the volumetric patch method[13].
Modern profilometers in use are almost entirely of the contactless type (e.g. laser, light slit or light sheet, to mention a few) and this document is primarily intended for this type. However, this does not exclude application of parts of it for other types of profilometers.
This ISO 13473 series has been prepared as a result of a need identified when specifying a test surface for vehicle noise measurement (see ISO 10844:2014[6]). Macrotexture depth measurements according to this document are not generally adequate for specifying test conditions of vehicle or traffic noise measurements, but have limited applications as a supplement in conjunction with other ways of specifying a surfacing.
This test method is suitable for determining the mean profile depth (MPD) of a pavement surface. This MPD can be transformed to a quantity which estimates the macrotexture depth according to the volumetric patch method. It is applicable to field tests as well as laboratory tests on pavement samples. When used in conjunction with other physical tests, the macrotexture depth values derived from this test method are applicable to estimation of pavement skid resistance characteristics (see e.g. Reference [15]), estimation of noise characteristics and assessment of the suitability of paving materials or pavement finishing techniques.
The method, together with other measurements (where applicable), such as porosity or microtexture, can be used to assess the quality of pavements.
This document is adapted for pavement texture measurement and is not intended for other applications. Pavement aggregate particle shape, size and distribution are surface texture features not addressed in this procedure. The method is not meant to provide a complete assessment of pavement surface texture characteristics. In particular, it is known that there are problems in interpreting the result if the method is applied to porous surfaces or to grooved surfaces (see Annex B).
NOTE Other International Standards dealing with surface profiling methods include, for example, References [1], [2] and [3]. Although it is not clearly stated in these, they are mainly used for measuring surface finish (microtexture) of metal surfaces and are not intended to be applied to pavements.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11819-2:2017(Main)
Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 2: The close-proximity method (ISO 11819-2:2017)
SIST EN ISO 11819-2:2017

ISO 11819-2:2017 specifies a method of evaluating different road surfaces with respect to their influence on traffic noise, under conditions when tyre/road noise dominates. The interpretation of the results applies to free-flowing traffic travelling on essentially level roads at constant speeds of 40 km/h and upwards, in which cases tyre/road noise is assumed to dominate (although in some countries it is possible that tyre/road noise does not dominate at 40 km/h when the proportion of heavy vehicles is high). For other driving conditions where traffic is not free-flowing, such as at junctions or under heavy acceleration, and where the traffic is congested, the influence of the road surface on noise emission is more complex. This is also the case for roads with high longitudinal gradients and a high proportion of heavy vehicles.
A standard method for comparing noise characteristics of road surfaces gives road and environment authorities a tool for establishing common practices or limits as to the use of surfacings meeting certain noise criteria. However, it is not within the scope of this document to suggest such criteria.
ISO 11819-1 defines another method: the statistical pass-by (SPB) method. The close-proximity (CPX) method specified in the present document has the same main objectives as the SPB method, but is intended to be used specifically in applications that are complementary to it, such as:
-      noise characterization of road surfaces at almost any arbitrary site, with the main purpose of checking compliance with a surface specification (an example for conformity of production is suggested in Reference [1]);
-      checking the acoustic effect of maintenance and condition, e.g. wear of and damage to surfaces, as well as clogging and the effect of cleaning of porous surfaces;
-      checking the longitudinal and lateral homogeneity of a road section;
-      the development of quieter road surfaces and research on tyre/road interaction.
NOTE          This document does not describe the conditions of application for formal purposes of the measurement with the CPX method. Such conditions may be defined in other standards or legal texts. However, suggestions for the applicability of ISO 11819-1 and this document are provided in Annex D.
Measurements with the CPX method are faster and more practical than with the SPB method, but are more limited in the sense that it is relevant only in cases where tyre/road noise dominates and power unit noise can be neglected. Furthermore, it cannot take heavy vehicle tyre/road noise into account as fully as the SPB method can, since it uses a light truck tyre as a proxy for heavy vehicle tyres and does not take power unit noise into account.
The CPX method specified in this document is intended to measure the properties of road surfaces, not the properties of tyres. If the method is used for research purposes, to provide an indication of differences between tyres, the loads and inflations would normally be adjusted to other values than specified in this document.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13473-5:2009(Main)
Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO 13473-5:2009)
SIST EN ISO 13473-5:2010

ISO 13473-5:2009 specifies procedures for determining the average depth or level of pavement surface megatexture by measuring the profile curve of a surface and calculating megatexture descriptors from this profile. The technique is designed to give meaningful and accurate measurement and description of pavement megatexture characteristics for various purposes.
Since there is an overlap between megatexture and the surrounding ranges, the megatexture descriptors unavoidably have a certain correlation with corresponding measures in those ranges. ISO 13473-5:2009 specifies measurements and procedures which are in relevant parts compatible with those in ISO 13473-1, ISO 8608 and EN 13036-5.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11819-1:2023(Main)
Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 1: Statistical Pass-By method (ISO 11819-1:2023)
SIST EN ISO 11819-1:2023

This document specifies a method of comparing traffic noise on different road surfaces for various compositions of road traffic for the purpose of evaluating different road surface types. Sound levels representing either light or heavy vehicles at selected speeds are assigned to a certain road surface. The method is applicable to traffic travelling at constant speed, i.e. free-flowing conditions at posted speeds of 50 km/h and upwards. For conditions where traffic is not free flowing, such as at junctions and where the traffic is congested, the method is not applicable.
A standard method for comparing the noise characteristics of road surfaces gives road and environment authorities a tool for establishing common practices or limits regarding the use of road surfaces meeting certain noise criteria. However, it is not within the scope of ISO 11819 (all parts) to suggest such criteria.
The statistical pass-by (SPB) method is suitable for use for the following main purposes:
—    to classify road surfaces according to their influence on traffic noise (surface classification);
—    to assist in verifying conformity of production of road surfaces;
—    to evaluate acoustic performance of road surfaces throughout operation relative to new condition;
—    to evaluate the influence of different road surfaces on traffic noise at sites irrespective of condition and service time;
—    to evaluate acoustic performance of a road surface relative to a reference surface.
Due to practical restrictions, the method cannot be applied at all possible locations. However, the backing board method can allow some locations to be tested that were not previously acceptable.
Clause 5 gives a general description of the SPB method.

  • Standard
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13473-1:2019(Main)
Characterization of pavement texture by use of surface profiles - Part 1: Determination of mean profile depth (ISO 13473-1:2019, Corrected version 2021-06)
SIST EN ISO 13473-1:2019

This document describes a test method to determine the average depth of pavement surface macrotexture (see Clause 3) by measuring the profile of a surface and calculating the texture depth from this profile. The technique is designed to provide an average depth value of only the pavement macrotexture and is considered insensitive to pavement microtexture and unevenness characteristics.
The objective of this document is to make available an internationally accepted procedure for determination of pavement surface texture depth which is an alternative to the traditionally used volumetric patch technique (generally using sand or glass beads), giving comparable texture depth values. To this end, this document describes filtering procedures that are designed to give the best possible representation of texture depths determined with the volumetric patch method[13].
Modern profilometers in use are almost entirely of the contactless type (e.g. laser, light slit or light sheet, to mention a few) and this document is primarily intended for this type. However, this does not exclude application of parts of it for other types of profilometers.
This ISO 13473 series has been prepared as a result of a need identified when specifying a test surface for vehicle noise measurement (see ISO 10844:2014[6]). Macrotexture depth measurements according to this document are not generally adequate for specifying test conditions of vehicle or traffic noise measurements, but have limited applications as a supplement in conjunction with other ways of specifying a surfacing.
This test method is suitable for determining the mean profile depth (MPD) of a pavement surface. This MPD can be transformed to a quantity which estimates the macrotexture depth according to the volumetric patch method. It is applicable to field tests as well as laboratory tests on pavement samples. When used in conjunction with other physical tests, the macrotexture depth values derived from this test method are applicable to estimation of pavement skid resistance characteristics (see e.g. Reference [15]), estimation of noise characteristics and assessment of the suitability of paving materials or pavement finishing techniques.
The method, together with other measurements (where applicable), such as porosity or microtexture, can be used to assess the quality of pavements.
This document is adapted for pavement texture measurement and is not intended for other applications. Pavement aggregate particle shape, size and distribution are surface texture features not addressed in this procedure. The method is not meant to provide a complete assessment of pavement surface texture characteristics. In particular, it is known that there are problems in interpreting the result if the method is applied to porous surfaces or to grooved surfaces (see Annex B).
NOTE Other International Standards dealing with surface profiling methods include, for example, References [1], [2] and [3]. Although it is not clearly stated in these, they are mainly used for measuring surface finish (microtexture) of metal surfaces and are not intended to be applied to pavements.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11819-2:2017(Main)
Acoustics - Measurement of the influence of road surfaces on traffic noise - Part 2: The close-proximity method (ISO 11819-2:2017)
SIST EN ISO 11819-2:2017

ISO 11819-2:2017 specifies a method of evaluating different road surfaces with respect to their influence on traffic noise, under conditions when tyre/road noise dominates. The interpretation of the results applies to free-flowing traffic travelling on essentially level roads at constant speeds of 40 km/h and upwards, in which cases tyre/road noise is assumed to dominate (although in some countries it is possible that tyre/road noise does not dominate at 40 km/h when the proportion of heavy vehicles is high). For other driving conditions where traffic is not free-flowing, such as at junctions or under heavy acceleration, and where the traffic is congested, the influence of the road surface on noise emission is more complex. This is also the case for roads with high longitudinal gradients and a high proportion of heavy vehicles.
A standard method for comparing noise characteristics of road surfaces gives road and environment authorities a tool for establishing common practices or limits as to the use of surfacings meeting certain noise criteria. However, it is not within the scope of this document to suggest such criteria.
ISO 11819-1 defines another method: the statistical pass-by (SPB) method. The close-proximity (CPX) method specified in the present document has the same main objectives as the SPB method, but is intended to be used specifically in applications that are complementary to it, such as:
-      noise characterization of road surfaces at almost any arbitrary site, with the main purpose of checking compliance with a surface specification (an example for conformity of production is suggested in Reference [1]);
-      checking the acoustic effect of maintenance and condition, e.g. wear of and damage to surfaces, as well as clogging and the effect of cleaning of porous surfaces;
-      checking the longitudinal and lateral homogeneity of a road section;
-      the development of quieter road surfaces and research on tyre/road interaction.
NOTE          This document does not describe the conditions of application for formal purposes of the measurement with the CPX method. Such conditions may be defined in other standards or legal texts. However, suggestions for the applicability of ISO 11819-1 and this document are provided in Annex D.
Measurements with the CPX method are faster and more practical than with the SPB method, but are more limited in the sense that it is relevant only in cases where tyre/road noise dominates and power unit noise can be neglected. Furthermore, it cannot take heavy vehicle tyre/road noise into account as fully as the SPB method can, since it uses a light truck tyre as a proxy for heavy vehicle tyres and does not take power unit noise into account.
The CPX method specified in this document is intended to measure the properties of road surfaces, not the properties of tyres. If the method is used for research purposes, to provide an indication of differences between tyres, the loads and inflations would normally be adjusted to other values than specified in this document.

  • Standard
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13473-5:2009(Main)
Characterization of pavement texture by use of surface profiles - Part 5: Determination of megatexture (ISO 13473-5:2009)
SIST EN ISO 13473-5:2010

ISO 13473-5:2009 specifies procedures for determining the average depth or level of pavement surface megatexture by measuring the profile curve of a surface and calculating megatexture descriptors from this profile. The technique is designed to give meaningful and accurate measurement and description of pavement megatexture characteristics for various purposes.
Since there is an overlap between megatexture and the surrounding ranges, the megatexture descriptors unavoidably have a certain correlation with corresponding measures in those ranges. ISO 13473-5:2009 specifies measurements and procedures which are in relevant parts compatible with those in ISO 13473-1, ISO 8608 and EN 13036-5.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13947:2024(Main)
Metallic powders - Test method for the determination of non-metallic inclusions in metal powders using a powder-forged specimen (ISO 13947:2024)
kSIST FprEN ISO 13947:2024

This document specifies a metallographic test method for determining the non-metallic inclusion level in metal powders using a powder-forged specimen. This test method is applicable to repress powder-forged test specimens in which there has been minimal lateral flow (<1 %). The core region of the powder-forged test specimen must not contain porosity detectable at 100x magnification.
This test method can also be applied to determine the non-metallic inclusion content of powder-forged steel parts. However, in parts where there has been a significant amount of material flow, the near-neighbour separation distance needs to be changed, or the inclusion sizes agreed between the parties need to be adjusted.
This test method is not applicable for determining the non-metallic inclusion level of parts that have been forged such that the core region contains porosity. At the magnification used for this test method, residual porosity is hard to distinguish from inclusions. Too much residual porosity makes a meaningful assessment of the inclusion population impossible.
This test method can also be applied to materials that contain manganese sulphide (admixed or prealloyed), provided the near-neighbour separation distance is changed from 30 µm to 15 µm.

  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 18034:2024(Main)
Algae and algae products - Methods of sampling and analysis - Determination of chlorophyll a content
kSIST FprEN 18034:2024

This document specifies a laboratory method for the determination of chlorophyll a content in algae. The method was initially tested and evaluated on the microalgae species Nannochloropsis sp. and a heat treated algal product tomato soup with Nannochloropsis sp. supplement, and the macro algae species Ulva sp., Furcellaria lumbricalis, and Saccharina latissima. During an Interlaboratory Trial the method was tested on the microalgae species Nannochloropsis sp. and the macro algae species Saccharina latissima. The microalgae species Nannochloropsis sp. and Phaodactlylum sp. and the macro algae species Ulva sp. and Saccharina latissima were tested in a Round Robin test. This document is only validated for chlorophyll a, but it can be used for other chlorophylls as well.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day