Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification

This European Standard specifies the requirements for factory made products of expanded polystyrene which are used for the thermal insulation of building equipment and industrial installations with an operating temperature range of approximately - 180 °C to + 80 °C. Modified expanded polystyrene polymers with a higher temperature resistance are also covered by this standard.
NOTE   Below an operating temperature of - 50 °C, special tests regarding the suitability of the product in the intended application are advised (e.g. liquefaction of oxygen). Manufacturers’ advice should be heeded in all cases.
The products are manufactured in the form of faced or unfaced boards, rolls, lags, pipe sections or other prefabricated ware.
This standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.
This standard does not specify the required level or class of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The classes and levels required for a given application can be found in regulations and invitations to tender.
Products with a declared thermal conductivity greater than 0,060 W/(m•K) at 10 °C are not covered by this standard.
This standard does not cover products for in situ insulation (for loose fill or poured insulation) or products for the insulation of the building structure.

Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation

Diese Europäische Norm legt die Anforderungen für werkmäßig hergestellte Produkte aus expandiertem Polystyrol fest, die als Wärmedämmstoffe für die technische Gebäudeausrüstung und betriebstechnische Anlagen in der Industrie im Temperaturbereich von etwa  180 °C bis +80 °C benutzt werden. Diese Europäische Norm gilt auch für expandierte modifizierte Polystyrol-Polymere mit einem höheren Temperaturwiderstand.
ANMERKUNG   Unterhalb einer Betriebstemperatur von 50 °C sind besondere Prüfungen bezüglich der Eignung der Produkte für den beabsichtigten Anwendungsfall ratsam (z. B. Sauerstoffverflüssigung). In jedem Fall sollten die Empfehlungen des Herstellers beachtet werden.
Die Produkte werden mit oder ohne Kaschierung in der Form von Platten, Rollen, Segmenten, Rohrschalen oder anderen vorgefertigten Produkten hergestellt.
Diese Europäische Norm beschreibt die Stoffeigenschaften und enthält die Prüfverfahren und Festlegungen für die Konformitätsbewertung, die Kennzeichnung und die Etikettierung.
In dieser Norm beschriebene Produkte werden auch in vorgefertigten Wärmedämmsystemen und Mehr¬schicht-Verbundplatten angewendet; die Eigenschaften von Systemen, in die diese Produkte integriert sind, werden nicht behandelt.
Diese Norm legt keine Leistungsstufen oder Klassen für eine vorgegebene Eigenschaft fest, die ein Produkt erreichen muss, um für einen bestimmten Anwendungsfall tauglich zu sein. Für bestimmte Anwendungen benötigte Klassen und Stufen können Regelwerken oder Ausschreibungen entnommen werden.
Diese Norm gilt nicht für Produkte, deren Nennwert der Wärmeleitfähigkeit größer ist als 0,060 W/(m  K) bei 10 °C.
Diese Norm gilt nicht für Produkte für an der Verwendungsstelle hergestellte Wärmedämmung (eingeblasen oder geschüttet) oder Produkte, die zur Dämmung von Gebäudehüllen bestimmt sind.

Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - Spécification

La présente Norme européenne spécifie les exigences relatives aux produits manufacturés en polystyrène expansé utilisés pour l'isolation thermique de l’équipement du bâtiment et des installations industrielles dont la température de service se situe entre – 180 °C et + 80 °C environ. Des polymères modifiés de polystyrène expansé ayant une résistance accrue à la température sont également couverts par la présente norme.
NOTE   Pour une température de service inférieure à – 50 °C, des essais particuliers sont recommandés pour s'assurer de l'aptitude à l'emploi du produit dans l'application visée (par exemple, liquéfaction de l'oxygène). Il convient de se référer systématiquement aux conseils du fabricant.
Les produits sont fabriqués sous la forme de panneaux avec ou sans parements, de rouleaux, de segments, de coquilles et autres pièces préfabriquées.
La présente norme décrit les caractéristiques des produits et comporte des modes opératoires d'essai, d'évaluation de conformité, de marquage et d’étiquetage.
Les produits couverts par la présente norme sont également utilisés dans des systèmes préfabriqués d'isolation thermique et dans des panneaux composites ; les performances des systèmes incorporant ces produits ne sont pas traitées.
La présente norme ne spécifie pas le niveau ou la classe requis pour une propriété donnée que doit posséder un produit pour démontrer son aptitude à une application particulière. Les classes ou niveaux requis pour une application particulière peuvent être trouvés dans les réglementations et les appels d'offres.
Les produits dont la conductivité thermique déclarée supérieure à 0,060 W/(m.K) à 10 °C ne sont pas couverts par la présente norme.
La présente norme ne couvre pas les produits pour isolation in situ (en vrac ou par déversement) ni ceux destinés à l’isolation de la structure du bâtiment.

Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekspandiranega polistirena (EPS) - Specifikacija

Ta evropski standard določa zahteve za proizvode iz ekspandiranega polistirena, ki se uporabljajo za toplotno izolacijo opreme stavb in industrijskih inštalacij z razponom delovne temperature približno od –180 °C do 80 °C. Modificirani polimeri ekspandiranega polistirena z višjo temperaturno odpornostjo so prav tako zajeti v tem standardu. OPOMBA Pod delovno temperaturo –50 °C se priporočajo posebni preskusi glede primernosti proizvoda za nameravano vrsto uporabe (npr. utekočinjenje kisika). V vseh primerih je treba upoštevati napotke proizvajalca. Proizvodi so izdelani v obliki prevlečenih ali neprevlečenih plošč, kolutov, oblog, vodovodnih odsekov ali drugih predizdelanih oblik. Ta standard opisuje lastnosti proizvodov ter zajema postopke za preskušanje, vrednotenje skladnosti, označevanje in etiketiranje. Proizvodi iz tega standarda se uporabljajo tudi v predizdelanih sistemih toplotne izolacije in vezanih ploščah; lastnosti sistemov iz teh proizvodov niso opisane. Ta standard ne določa zahtevane ravni ali razreda določene lastnosti, ki jo mora proizvod doseči, da se dokaže njegova primernost namenu za posamezno vrsto uporabe. Zahtevani razredi in ravni za posamezno uporabo so določeni v uredbah in javnih razpisih. Proizvodi z deklarirano toplotno prevodnostjo, višjo od 0,060 W/mK pri 10 °C, v tem standardu niso zajeti. Ta standard ne zajema proizvodov za izolacijo na kraju samem (za izolacijo s prostim polnilom ali vlivano izolacijo) ali proizvodov za izolacijo stavbne strukture.

General Information

Status
Withdrawn
Publication Date
29-Jan-2013
Withdrawal Date
08-Dec-2015
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
09-Dec-2015

Relations

Buy Standard

Standard
EN 14309:2010+A1:2013
English language
50 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Toplotnoizolacijski proizvodi za opremo stavb in industrijske inštalacije - Proizvodi iz ekspandiranega polistirena (EPS) - SpecifikacijaWärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - SpezifikationProduits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - SpécificationThermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification91.100.60Thermal and sound insulating materialsICS:Ta slovenski standard je istoveten z:EN 14309:2009+A1:2013SIST EN 14309:2010+A1:2013en,fr,de01-maj-2013SIST EN 14309:2010+A1:2013SLOVENSKI
STANDARD



SIST EN 14309:2010+A1:2013



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14309:2009+A1
January 2013 ICS 91.100.60 Supersedes EN 14309:2009English Version
Thermal insulation products for building equipment and industrial installations - Factory made products of expanded polystyrene (EPS) - Specification
Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles - Produits manufacturés en polystyrène expansé (PSE) - Spécification
Wärmedämmstoffe für die technische Gebäudeausrüstung und für betriebstechnische Anlagen in der Industrie - Werkmäßig hergestellte Produkte aus expandiertem Polystyrol (EPS) - Spezifikation This European Standard was approved by CEN on 29 September 2009 and includes Amendment 1 approved by CEN on 11 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14309:2009+A1:2013: ESIST EN 14309:2010+A1:2013



EN 14309:2009+A1:2013 (E) 2 Contents Page Foreword .4 1 Scope .6 2 Normative references .6 3 Terms, definitions, symbols, units and abbreviated terms .8 4 Requirements . 11 5 Test methods . 20 6 Designation code . 24 7 Evaluation of Conformity . 25 8 Marking and labelling . 26 Annex A (normative)
Factory production control . 27 Annex B (normative)
Product classification . 34 Annex C (normative)
Determination of minimum service temperature . 35 Annex D (informative)
Additional properties .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.