EN 13775-1:2003

Railway applications - Measuring of new and modified freight wagons - Part 1: Measuring principles

This European Standard specifies requirements for measuring freight wagons and bogies. This ensures that the measuring methods are applied in accordance with uniform criteria. It applies to new and modified freight wagons and bogies. Provisions going beyond the scope of these requirements should be agreed upon by the contracting parties involved.
The measuring methods relate to the whole or parts of the underframes with or without add-ons if the geometrical structure does not permit anything else. Where appropriate, other measuring methods not specified here are necessary and should be specified in each individual case. This applies as appropriate to bogies.

Bahnanwendungen - Vermessung von Güterwagen beim Neubau und bei Umbauten - Teil 1: Meßgrundsätze

In dieser Europäischen Norm sind die Anforderungen für das Vermessen von Güterwagen und Drehgestellen festgelegt. Durch diese wird sichergestellt, daß Meßvorgänge nach einheitlichen Kriterien ausgeführt werden. Sie gilt für neue und umgebaute Güterwagen oder Drehgestelle. Über diese Anforderungen dieser Norm hinausgehende Forderungen sind zwischen den Vertragspartnern zu vereinbaren. Durch das Vermessen ist festzustellen, ob die Abweichungen von den Nennmaßen innerhalb der in den Teilen 2 bis 6 dieser Normenreihe festgelegten Toleranzen liegen.

Applications ferroviaires - Mesure des wagons lors de leur construction et lors de modifications - Partie 1: Principes de mesure

La présente norme européenne précise les exigences concernant les mesures des wagons et des bogies, qui assurent que les opérations de mesure sont effectuées en fonction de critères unifiés. Elle est applicable aux wagons et aux bogies neufs et modifiés. Les exigences allant au-delà de ladite norme doivent faire l'objet d'une convention particulière entre contractants. Les mesures doivent garantir que les écarts par rapport aux cotes nominales ne dépassent pas les tolérances fixées dans les parties 2 à 6 de la présente série.

Železniške naprave – Merjenje novih in predelanih tovornih vagonov – 1.del: Načela za izvajanje meritev

General Information

• Status: Published
• Publication Date: 17-Jun-2003
• ICS: 45.060.20 - Trailing stock
• Technical Committee: CEN/TC 256 - Railway applications
• Drafting Committee: CEN/TC 256/WG 26 - Freight wagons
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 13-Jun-2022
• Directive: 93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
• Mandate: M/024 - Mandate to CEN/CENELEC/ETSI for programming and standardization in the field of railway equipment
• Ref Project: SIST EN 13775-1:2004 - Railway applications - Measuring of new and modified freight wagons - Part 1: Measuring principles

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bahnanwendungen - Vermessung von Güterwagen beim Neubau und bei Umbauten - Teil 1: MeßgrundsätzeApplications ferroviaires - Mesure des wagons lors de leur construction et lors de modifications - Partie 1: Principes de mesureRailway applications - Measuring of new and modified freight wagons - Part 1: Measuring principles45.060.20Železniški vagoniTrailing stockICS:Ta slovenski standard je istoveten z:EN 13775-1:2003SIST EN 13775-1:2004en01-junij-2004SIST EN 13775-1:2004SLOVENSKI
STANDARD



SIST EN 13775-1:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13775-1June 2003ICS 45.060.20English versionRailway applications - Measuring of new and modified freightwagons - Part 1: Measuring principlesApplications ferroviaires - Mesure des wagons lors de leurconstruction et lors de modifications - Partie 1: Principes demesureBahnanwendungen - Vermessung von Güterwagen beimNeubau und bei Umbauten - Teil 1: MeßgrundsätzeThis European Standard was approved by CEN on 14 February 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13775-1:2003 ESIST EN 13775-1:2004



EN 13775-1:2003 (E)2ContentspageForeword.3Introduction.41Scope.42Normative references.43Terms and definitions.44Requirements.54.1General.54.2Conditions.54.3Temperature.54.4Measuring principle.54.5Measuring equipment.64.6Measuring points, dimensional designations.65Driving direction, vehicle ends and sides.75.1General.75.2Driving Direction.75.3Vehicle ends and sides.75.4Bogie ends.8Bibliography.9SIST EN 13775-1:2004



EN 13775-1:2003 (E)3ForewordThis document (EN 13775-1:2003) has been prepared by Technical Committee CEN /TC 256"Railway applications", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard,
...