iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 802:1994

(Main)

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing

Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing

This standard specifies a method for applying a crushing test to injection- moulded thermoplastics fittings intended for pressure piping systems to determine whether or not fracture will occur at a specified deformation.

Kunststoff-Rohrleitungs- und Schutzrohrsysteme - Spritzguß-Formstücke aus Thermoplasten für Druckrohrleitungen - Prüfverfahren für die Verformung durch Quetschen

Diese Norm legt ein Verfahren zur Durchführung eines Quetschversuches an Spritzguss-Formstücken aus Thermoplasten für Druckrohrleitungen fest, um zu bestimmen ob bei festgelegter Verformung ein Bruch aufritt.

Systèmes de canalisations et de gaines en plastiques - Raccords thermoplastiques moulés par injection pour canalisations avec pression - Méthode d'essai de déformation maximale par écrasement

Cette norme prescrit une méthode d'application d'une force d'écrasement à des raccords thermoplastiques moulés pour canalisations avec pression pour déterminer s'il y a rupture ou non, pour une déformation spécifiée.

Cevni sistemi iz polimernih materialov - Plastomerni fitingi, oblikovani z injekcijskim vbrizgavanjem, za tlačne cevovode - Metoda za preskus največje deformacije s stiskanjem

General Information

Status
Published
Publication Date
29-Apr-1994
Withdrawal Date
30-Oct-1994
ICS
23.040.45 - Plastics fittings
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
25-Feb-2023
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
SIST EN 802:1997 - Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for pressure piping systems - Test method for maximum deformation by crushing

Buy Standard

EN 802:1997EN 802:1997
PreviousNext
Standard
EN 802:1997
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 802:1997
01-februar-1997
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY3ODVWRPHUQLILWLQJLREOLNRYDQL]
LQMHNFLMVNLPYEUL]JDYDQMHP]DWODþQHFHYRYRGH0HWRGD]DSUHVNXVQDMYHþMH
GHIRUPDFLMHVVWLVNDQMHP
Plastics piping and ducting systems - Injection-moulded thermoplastics fittings for
pressure piping systems - Test method for maximum deformation by crushing
Kunststoff-Rohrleitungs- und Schutzrohrsysteme - Spritzguß-Formstücke aus
Thermoplasten für Druckrohrleitungen - Prüfverfahren für die Verformung durch
Quetschen
Systemes de canalisations et de gaines en plastiques - Raccords thermoplastiques
moulés par injection pour canalisations avec pression - Méthode d'essai de déformation
maximale par écrasement
Ta slovenski standard je istoveten z: EN 802:1994
ICS:
23.040.45 Fitingi iz polimerni
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN ISO 7510:2024(Main)
Plastics piping systems - Glass-reinforced plastics (GRP) components - Determination of the amounts of constituents (ISO 7510:2017)
SIST EN ISO 7510:2024

ISO 7510:2017 specifies a method for the determination of constituent materials of a test sample cut from a glass-reinforced plastics (GRP) component intended for use in a piping system. It includes determination of resin, glass, aggregate and filler contents.
It is also applicable to the determination of the type and arrangement of the reinforcements. If used to determine the amounts of constituent materials in layered constructions it may be necessary to separate the laminate layers by cutting or splitting and testing each separately.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12201-3:2024(Main)
Plastics piping systems for water supply, and for drains and sewers under pressure - Polyethylene (PE) - Part 3: Fittings
SIST EN 12201-3:2024

This document specifies the characteristics of fusion fittings made from polyethylene (PE) as well as of mechanical fittings for buried and above ground applications, intended for the conveyance of water for human consumption, raw water prior to treatment, drains and sewers under pressure, vacuum sewer systems, and water for other purposes, with the exception of industrial application.
NOTE 1   For PE components intended for the conveyance of water for human consumption and raw water prior to treatment, attention is drawn to subclause 6.6 of this document. Components manufactured for water for other purposes, drains and sewers, and vacuum sewer systems are possibly not suitable for water supply for human consumption.
NOTE 2   Industrial application is covered by EN ISO 15494 [4].
The intended uses include sea outfalls, laid in water and pipes suspended below bridges.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 12201-1, EN 12201 2, EN 12201 4 and EN 12201 5, this document is applicable to PE pipes, fittings and valves, their joints and joints with components of PE and other materials intended to be used under the following conditions:
a)   allowable operating pressure, PFA, up to 25 bar  ;
b)   an operating temperature of 20 °C as a reference temperature.
NOTE 3   For applications operating at constant temperature greater than 20 °C and up to and including 50 °C, see EN 12201-1:2024, Annex A.
The EN 12201 series covers a range of allowable operating pressures and gives requirements concerning colours.
NOTE 4   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national guidance or regulations and installation practices or codes.
These fittings can be of the following types:
—   electrofusion socket fittings;
—   electrofusion saddle fittings;
—   spigot end fittings (for butt fusion using heated tools and electrofusion socket fusion);
—   socket fusion fittings (see Annex A);
—   mechanical fittings;
—   fabricated fittings (see Annex B).

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
SIST EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
SIST EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
SIST EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17176-3:2022(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 3: Fittings
SIST-TS CEN/TS 17176-3:2022

This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. The scope of this document is limited to double sockets, repair couplings, reducers and to non-end load bearing elbows.
NOTE 1   The scope of this document is restricted to fittings on the market during the preparation of this document. Therefore, tees, flange adaptors, etc., are excluded from this version of the standard.
NOTE 2   For double sockets, repair couplings and reducers there are no special fittings designs for end-load bearing applications. However, restrained gaskets can be used for end-load bearing applications. In that case, the requirements of EN 17176-5 are applicable.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 17176-1 and EN 17176-5, this document is applicable to oriented PVC-O fittings intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)   irrigation under pressure.
This document is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations. For temperatures between 25 °C and 45 °C, EN 17176-2:2019, Figure C.1 applies.
This document specifies a range of fittings sizes and pressure classes and gives a requirement and recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15875-3:2003/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 3: Fittings - Amendment 2 (ISO 15875-3:2003/Amd 2:2021)
SIST EN ISO 15875-3:2004/A2:2021
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22391-3:2009/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittings - Amendment 2 (ISO 22391-3:2009/Amd 2:2021)
SIST EN ISO 22391-3:2010/A2:2021
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15874-3:2013/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 2 (ISO 15874-3:2013/Amd 2:2021)
SIST EN ISO 15874-3:2013/A2:2021
  • Amendment
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21003-3:2008/A1:2021(Amendment)
Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings - Amendment 1 (ISO 21003-3:2008/Amd 1:2021)
SIST EN ISO 21003-3:2009/A1:2021
  • Amendment
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day