EN ISO 10684:2004
(Main)Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
ISO 10684:2004 specifies material, process, dimensional and some performance requirements for hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64 and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below 1,25 mm.
ISO 10684:2004 primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to other threaded steel parts. The specifications given in this document may also be applied to non-threaded steel parts such as washers.
Verbindungselemente - Feuerverzinkung (ISO 10684:2004)
Diese Internationale Norm legt Werkstoff, Verfahren, Maßanforderungen und einige Leistungsanforderungen
für die Feuerverzinkung von Verbindungselementen aus Stahl mit Regelgewinde von M8 bis M64 und für die
Festigkeitsklassen bis einschließlich 10.9 für Schrauben und 12 für Muttern fest. Feuerverzinkung wird für
Verbindungselemente mit Gewinden kleiner als M8 und/oder mit Gewindesteigung unterhalb 1,25 mm nicht
empfohlen.
ANMERKUNG Es wird darauf hingewiesen, dass die Prüfkräfte und Prüfspannungen von Muttern mit Gewindeübermaß
der Gewindegrößen M8 und M10 sowie die Bruchkräfte und Prüfkräfte von Schrauben mit Gewindeuntermaß der Gewindegrößen
M8 und M10 geringer sind als die in ISO 898-2 bzw. ISO 898-1 vorgegebenen Werte. Sie werden im normativen
Anhang A festgelegt.
Die Norm behandelt in erster Linie Feuerverzinken mit Schleudern von Verbindungselementen aus Stahl mit
Gewinde, sie kann aber auch auf andere Gewindeteile aus Stahl angewendet werden.
Die in dieser Internationalen Norm enthaltenen Festlegungen können auch auf Teile aus Stahl ohne Gewinde,
wie z. B. Scheiben, angewendet werden.
Éléments de fixation - Revêtements de galvanisation à chaud (ISO 10684:2004)
L'ISO 10684:2004 spécifie les matériaux, les étapes du procédé de revêtement, les dimensions et certaines caractéristiques fonctionnelles des revêtements de galvanisation à chaud au trempé (avec essorage). Elle s'applique aux éléments de fixation à filetage à pas gros de M8 à M64 inclus, de classes de qualité jusqu'à 10.9 incluse pour les vis et goujons et de classes de qualité jusqu'à 12 incluse pour les écrous. La galvanisation à chaud n'est pas recommandée pour les éléments de fixation filetés de filetage inférieur à M8 et/ou de pas inférieur à 1,25 mm.
L'ISO 10684:2004 concerne principalement les éléments de fixation filetés galvanisés à chaud au trempé (avec essorage), mais peut également s'appliquer à d'autres pièces filetées en acier. Les spécifications indiquées dans ce document peuvent également s'appliquer à des pièces en acier non filetées telles que les rondelles.
Vezni elementi - Z vročim pocinkanjem nanesene prevleke (ISO 10684:2004)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2004
9H]QLHOHPHQWL=YURþLPSRFLQNDQMHPQDQHVHQHSUHYOHNH ,62
Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
Verbindungselemente - Feuerverzinkung (ISO 10684:2004)
Éléments de fixation - Revetements de galvanisation a chaud (ISO 10684:2004)
Ta slovenski standard je istoveten z: EN ISO 10684:2004
ICS:
21.060.01 Vezni elementi na splošno Fasteners in general
25.220.40 Kovinske prevleke Metallic coatings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10684
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 25.220.40; 21.060.01
English version
Fasteners - Hot dip galvanized coatings (ISO 10684:2004)
Éléments de fixation - Revêtements de galvanisation à Verbindungselemente - Feuerverzinkung (ISO 10684:2004)
chaud (ISO 10684:2004)
This European Standard was approved by CEN on 17 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10684:2004: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 10684:2004) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 "Threaded and non-
threaded mechanical fasteners and accessories", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 10684:2004 has been approved by CEN as EN ISO 10684:2004 without any
modifications.
INTERNATIONAL ISO
STANDARD 10684
First edition
2004-07-15
Fasteners — Hot dip galvanized coatings
Éléments de fixation — Revêtements de galvanisation à chaud
Reference number
ISO 10684:2004(E)
©
ISO 2004
ISO 10684:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 10684:2004(E)
Contents Page
Foreword. iv
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Materials. 3
4.1 Raw material of parts. 3
4.2 Zinc. 3
5 Hot dip galvanizing procedures and precautions . 3
5.1 Stress relief. 3
5.2 Cleaning and pickling. 3
5.3 Baking. 3
5.4 Fluxing. 3
5.5 Hot dip galvanizing . 3
5.6 Spinning and quenching . 4
5.7 Special requirements for nuts . 4
5.8 Post-treatment. 4
6 Requirements on thread tolerances and additional marking . 4
6.1 General. 4
6.2 Requirements and precautions in assembling hot dip galvanized threaded fasteners . 4
6.3 Special requirements for marking when supplying fasteners in sealed containers. 8
7 Mechanical properties of nuts tapped oversize and undersize threaded bolts, screws and
studs. 8
8 Coating requirements. 8
8.1 Appearance of zinc coating . 8
8.2 Considerations for hot dip galvanized washers . 8
8.3 Zinc coating thickness . 8
8.4 Adhesion of zinc coating. 8
9 Lubrication. 9
10 Ordering requirements. 9
11 Designation. 9
Annex A (normative) Special requirements for bolts, screws and nuts with thread sizes M8 and
M10 . 11
Annex B (normative) Limits of sizes for hot dip galvanized internal and external screw thread M8 . 13
Annex C (informative) Calculation of minimum ultimate tensile loads and proof loads for bolts
and screws M8 and M10 with threads undersized to tolerance class 6az . 15
Annex D (informative) Surface areas of bolts, screws and nuts . 16
Annex E (normative) Adherence of hot-dip galvanized coating. 19
Annex F (informative) Strength of hot dip galvanized bolt or screw and nut assemblies. 20
ISO 10684:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10684 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 1, Mechanical
properties of fasteners.
iv © ISO 2004 – All rights reserved
INTERNATIONAL STANDARD ISO 10684:2004(E)
Fasteners — Hot dip galvanized coatings
1 Scope
This International Standard specifies material, process, dimensional and some performance requirements for
hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64
and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not
recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below
1,25 mm.
NOTE Attention is drawn to the fact that the proof loads and stresses under proof load of oversize tapped nuts with
threads M8 and M10 and the ultimate tensile loads and proof loads of undersize threaded bolts and screws with threads
M8 and M10 are reduced as compared to the values specified in ISO 898-2 and ISO 898-1 respectively and are specified
in Annex A.
It primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to
other threaded steel parts.
The specifications given in this International Standard may also be applied to non-threaded steel parts such
as washers.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs
ISO 898-2, Mechanical properties of fasteners — Part 2: Nuts with specified proof load values — Coarse
thread
ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data
ISO 965-2, ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general
purpose external and internal screw threads — Medium quality
ISO 965-3, ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional
screw threads
ISO 965-4, ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip
galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G
after galvanizing
ISO 965-5, ISO general purpose metric screw threads
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.