EN IEC 62841-3-7:2021
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
IEC 62841-3-7:2020 This document applies to transportable wall saws guided by a track guiding system intended for dry cutting or to be connected to a liquid system for cutting concrete, stone or similar material by means of a diamond wheel. The rated speed of the diamond wheel does not exceed a peripheral speed of 100 m/s at rated capacity. The rated voltage is not more than 250 V for single-phase a.c. or d.c. tools, and 480 V for three-phase a.c. tools. This document does not apply to transportable wall saws that are intended to be left unattended while performing an operation. This document does not apply to transportable wall saws that employ hydraulic systems. This document does not apply to hand-held cut-off machines.
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-7: Besondere Anforderungen für transportable Wandsägen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-7: Exigences particulières pour les scies murales portables
IEC 62841-3-7:2020 Le présent document s'applique aux scies murales portables guidées par un système de guidage de piste, destinées à couper à sec ou à être raccordées à un système liquide pour couper du béton, de la pierre ou un matériau similaire au moyen d'une meule diamant. La vitesse assignée de la meule diamant ne dépasse pas une vitesse périphérique de 100 m/s à la capacité assignée. La tension assignée est inférieure à 250 V pour les outils à courant monophasé alternatif ou continu, et inférieure à 480 V pour les outils à courant alternatif triphasé. Le présent document ne s’applique pas aux scies murales portables qui sont destinées à être laissées sans surveillance pendant l’exécution d’une manœuvre. Le présent document ne s’applique pas aux scies murales portables qui utilisent des systèmes hydrauliques. Le présent document ne s'applique pas aux machines à tronçonner portatives.
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-7. del: Posebne zahteve za premične stenske žage
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2021
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
7. del: Posebne zahteve za premične stenske žage
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-7: Particular requirements for transportable wall saws
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und
Rasen- und Gartenmaschinen – Sicherheit – Teil 3-7: Besondere Anforderungen für
transportable Wandsägen
Ta slovenski standard je istoveten z: EN IEC 62841-3-7:2021
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 62841-3-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2021
ICS 25.140.20
English Version
Electric motor-operated hand-held tools, transportable tools and
lawn and garden machinery - Safety - Part 3-7: Particular
requirements for transportable wall saws
(IEC 62841-3-7:2020)
Outils électroportatifs à moteur, outils portables et machines Elektrische motorbetriebene handgeführte Werkzeuge,
pour jardins et pelouses - Sécurité - Partie 3-7: Exigences transportable Werkzeuge und Rasen- und
particulières pour les scies murales portables Gartenmaschinen - Sicherheit - Teil 3-7: Besondere
(IEC 62841-3-7:2020) Anforderungen für transportable Wandsägen
(IEC 62841-3-7:2020)
This European Standard was approved by CENELEC on 2020-07-16. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62841-3-7:2021 E
European foreword
The text of document 116/455/FDIS, future edition 1 of IEC 62841-3-7, prepared by IEC/TC 116
"Safety of motor-operated electric tools" was submitted to the IEC-CENELEC parallel vote and
approved by CENELEC as EN IEC 62841-3-7:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-04-26
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-04-26
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CENELEC by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of
Endorsement notice
The text of the International Standard IEC 62841-3-7:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
ISO 11203:1995 NOTE Harmonized as EN ISO 11203:2009 (not modified)
IEC 62841-3-7 ®
Edition 1.0 2020-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric motor-operated hand-held tools, transportable tools and lawn and
garden machinery – Safety –
Part 3-7: Particular requirements for transportable wall saws
Outils électroportatifs à moteur, outils portables et machines pour jardins et
pelouses – Sécurité –
Partie 3-7: Exigences particulières pour les scies murales portables
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.140.20 ISBN 978-2-8322-8443-8
– 2 – IEC 62841-3-7:2020 © IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 7
4 General requirements . 9
5 General conditions for the tests . 9
6 Radiation, toxicity and similar hazards . 9
7 Classification . 9
8 Marking and instructions . 10
9 Protection against access to live parts . 12
10 Starting . 12
11 Input and current . 12
12 Heating . 12
13 Resistance to heat and fire . 12
14 Moisture resistance . 12
15 Resistance to rusting . 15
16 Overload protection of transformers and associated circuits . 15
17 Endurance . 15
18 Abnormal operation . 15
19 Mechanical hazards . 16
20 Mechanical strength . 18
21 Construction . 19
22 Internal wiring . 20
23 Components . 20
24 Supply connection and external flexible cords . 21
25 Terminals for external conductors . 22
26 Provision for earthing . 22
27 Screws and connections . 22
28 Creepage distances, clearances and distances through insulation . 22
Annexes . 23
Annex C (normative) Leakage current . 23
Annex I (informative) Measurement of noise and vibration emissions . 24
Annex K (normative) Battery tools and battery packs . 28
Bibliography . 29
Figure 101 – Wall saw . 8
Figure 102 – Wall saw with wheel guard removed . 9
Figure 103 – Safety sign illustrating – "WARNING – Always wear eye protection" . 10
Figure I.101 – Wall saw setup for noise measurement (wheel guard not shown) . 25
IEC 62841-3-7:2020 © IEC 2020 – 3 –
Table 4 – Required performance levels . 16
Table 101 – Material properties and minimum thickness of the wheel guard . 18
Table 8 – Minimum cross-sectional area and AWG sizes of supply cords . 21
Table I.101 – Expected uncertainty values . 27
– 4 – IEC 62841-3-7:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
TOOLS AND LAWN AND GARDEN MACHINERY –
SAFETY –
Part 3-7: Particular requirements for transportable wall saws
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.