Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities - Part 3: E-cores

IEC 63182-3:2021 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of E-cores made of metallic magnetic powder, the essential dimensions of coil formers to be used with them as well as the effective parameter values to be used in calculations involving them, and gives guidelines on allowable limits of surface irregularities applicable to E-cores. This document is a specification useful in the negotiations between magnetic powder core suppliers and users about surface irregularities.

Magnetische Pulverkerne – Leitlinien zu Maßen und Grenzen von Oberflächenbeschädigungen - Teil 3: E-Kerne

Noyaux en poudre magnétique – Lignes directrices concernant les dimensions et les limites des irrégularités de surface – Partie 3: Noyaux E

L’IEC 63182-3:2021 spécifie les dimensions qui sont importantes pour l’interchangeabilité mécanique d’une gamme préférentielle de noyaux E en poudre magnétique métallique, ainsi que les dimensions essentielles des supports de bobinages à employer avec ces noyaux E. Elle spécifie également les valeurs des paramètres effectifs à utiliser dans les calculs concernant ces derniers et donne des lignes directrices relatives aux limites admissibles des irrégularités de surface applicables aux noyaux E. Le présent document est une spécification utile pour les négociations sur les irrégularités de surface entre les fournisseurs et les utilisateurs de noyaux en poudre magnétique.

Jedra iz magnetnega prahu - Smernice o merah in mejnih vrednostih površinskih nepravilnosti - 3. del: E-jedra

Ta del standarda IEC 63182 določa mere, ki so pomembne za mehansko medsebojno zamenljivost prednostnega razpona E-jeder, izdelanih iz kovinskega magnetnega prahu, bistvene mere tuljave, ki se uporablja s temi jedri, in vrednosti efektivnih parametrov, ki se uporabljajo pri izračunih, povezanih z jedri, ter podaja smernice o dovoljenih mejnih vrednostih površinskih nepravilnosti, ki se uporabljajo za E-jedra. Ta dokument je specifikacija, uporabna za sklepanje dogovorov o površinskih nepravilnostih med dobavitelji in uporabniki jeder iz magnetnega prahu. Uporaba »izpeljanih« standardov, ki podajajo podrobnejše specifikacije o delih komponent in hkrati dovoljujejo skladnost s tem dokumentom, je obravnavana v dodatku A.

General Information

Status
Published
Publication Date
10-Feb-2022
Current Stage
6060 - Document made available - Publishing
Start Date
11-Feb-2022
Completion Date
11-Feb-2022

Buy Standard

Standard
EN IEC 63182-3:2022
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2022
Jedra iz magnetnega prahu - Smernice o merah in mejnih vrednostih površinskih
nepravilnosti - 3. del: E-jedra
Magnetic powder cores - Guidelines on dimensions and the limits of surface irregularities
- Part 3: E-cores
Ta slovenski standard je istoveten z: EN IEC 63182-3:2022
ICS:
29.100.10 Magnetne komponente Magnetic components
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 63182-3

NORME EUROPÉENNE
EUROPÄISCHE NORM February 2022
ICS 29.100.10
English Version
Magnetic powder cores - Guidelines on dimensions and the
limits of surface irregularities - Part 3: E-cores
(IEC 63182-3:2021)
Noyaux en poudre magnétique - Lignes directrices Magnetische Pulverkerne - Leitlinien zu Maßen und
concernant les dimensions et les limites des irrégularités de Grenzen von Oberflächenbeschädigungen - Teil 3: E-Kerne
surface - Partie 3: Noyaux E (IEC 63182-3:2021)
(IEC 63182-3:2021)
This European Standard was approved by CENELEC on 2022-01-20. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 63182-3:2022 E

European foreword
The text of document 51/1397/FDIS, future edition 1 of IEC 63182-3, prepared by IEC/TC 51
"Magnetic components, ferrite and magnetic powder materials" was submitted to the IEC-CENELEC
parallel vote and approved by CENELEC as EN IEC 63182-3:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-10-20
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-01-20
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 63182-3:2021 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60205 - Calculation of the effective parameters of EN 60205 -
magnetic piece parts
IEC 63182-1 - Magnetic powder cores - Guidelines on EN IEC 63182-1 -
dimensions and the limits of surface
irregularities - Part 1: General specification

IEC 63182-3 ®
Edition 1.0 2021-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic powder cores – Guidelines on dimensions and the limits of surface

irregularities –
Part 3: E-cores
Noyaux en poudre magnétique – Lignes directrices concernant les dimensions

et les limites des irrégularités de surface –

Partie 3: Noyaux E
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.100.10 ISBN 978-2-8322-1061-3

– 2 – IEC 63182-3:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Primary dimensions . 5
4.1 General . 5
4.2 Dimensions of E-cores . 6
4.2.1 Main dimensions . 6
4.2.2 Effective parameter and A values . 7
min
4.3 Dimensional limits for coil formers . 8
5 Limits of surface irregularities . 8
5.1 General . 8
5.2 Examples of surface irregularities . 9
5.3 Chips and ragged edges . 9
5.3.1 General . 9
5.3.2 Chips and ragged edges on the mating surfaces . 9
5.3.3 Chips and ragged edges on the other surfaces . 9
5.4 Cracks . 10
5.5 Flash . 11
5.6 Rust . 11
5.7 Discoloration . 11
Annex A (normative) Derived standards . 12

Figure 1 – Main dimensions of E-cores . 6
Figure 2 – Main dimensions of coil formers for E-cores . 8
Figure 3 – Examples of surface irregularities . 9
Figure 4 – Locations of chips and ragged edges for E-cores . 10
Figure 5 – Locations of cracks for E-cores . 10
Figure 6 – Locations of flashes for E-cores . 11
Figure 7 – Rust location for E-cores . 11

Table 1 – Main dimensions of E-cores . 6
Table 2 – Effective parameter and A values . 7
min
Table 3 – Dimensional limits for coil formers for E-cores . 8

IEC 63182-3:2021 © IEC 2021 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
MAGNETIC POWDER CORES – GUIDELINES ON DIMENSIONS
AND THE LIMITS OF SURFACE IRREGULARITIES –

Part 3: E-cores
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 63182-3 has been prepared by IEC technical committee 51: Magnetic components, ferrite
and magnetic powder materials. It is an International Standard.
The text of this International Standard is based on the following documents:
Draft Report on voting
51/1397/FDIS 51/1402/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.

– 4 – IEC 63182-3:2021 © IEC 2021
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts in the IEC 63182 series, published under the general title Magnetic powder
cores – Guidelines on dimensions and the limits of surface irregularities can be found on the
IEC website.
The committee has decided that the co
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.