FprEN IEC 62841-3-16:2025
(Main)Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-16: Particular requirements for transportable belt sanders, disc sanders and belt/disc sanders
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 3-16: Particular requirements for transportable belt sanders, disc sanders and belt/disc sanders
Elektrische motorbetriebene handgeführte Werkzeuge, transportable Werkzeuge und Rasen- und Gartenmaschinen - Sicherheit - Teil 3-16: Besondere Anforderungen für transportable Bandschleifmaschinen, Scheibenschleifmaschinen und Band-/Scheibenschleifmaschinen
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses - Sécurité - Partie 3-16: Exigences particulières pour les ponceuses à bande, les ponceuses à disque et les ponceuses à bande/disque portables
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-16. del: Posebne zahteve za prenosne tračne brusilnike, diskovne brusilnike in tračne/diskovne brusilnike
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 62841-3-16:2024
01-november-2024
Elektromotorna ročna orodja, prenosna orodja ter stroji za trato in vrt - Varnost - 3-
16. del: Posebne zahteve za prenosne tračne brusilnike, diskovne brusilnike in
tračne/diskovne brusilnike
Electric motor-operated hand-held tools, transportable tools and lawn and garden
machinery - Safety - Part 3-16: Particular requirements for transportable belt sanders,
disc sanders and belt/disc sanders
Outils électroportatifs à moteur, outils portables et machines pour jardins et pelouses -
Sécurité - Partie 3-16: Exigences particulières pour les ponceuses à bande, les
ponceuses à disque et les ponceuses à bande/disque portables
Ta slovenski standard je istoveten z: prEN IEC 62841-3-16:2024
ICS:
25.140.20 Električna orodja Electric tools
oSIST prEN IEC 62841-3-16:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 62841-3-16:2024
oSIST prEN IEC 62841-3-16:2024
116/825/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62841-3-16 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2024-09-27 2024-12-20
SUPERSEDES DOCUMENTS:
116/766/NP, 116/817/RVN
IEC TC 116 : SAFETY OF MOTOR-OPERATED ELECTRIC TOOLS
SECRETARIAT: SECRETARY:
United States of America Mr Joseph Harding
OF INTEREST TO THE FOLLOWING COMMITTEES: HORIZONTAL FUNCTION(S):
ASPECTS CONCERNED:
Safety
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).
TITLE:
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery -
Safety - Part 3-16: Particular requirements for transportable belt sanders, disc sanders and
belt/disc sanders
PROPOSED STABILITY DATE: 2031
NOTE FROM TC/SC OFFICERS:
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
oSIST prEN IEC 62841-3-16:2024
IEC CDV 62841-3-16 ED1 © IEC 2024 2 116/825/CDV
1 CONTENTS
2 FOREWORD . 2
3 1 Scope . 4
4 2 Normative references . 4
5 3 Terms and definitions . 4
6 4 General requirements . 6
7 5 General conditions for the tests . 6
8 6 Radiation, toxicity and similar hazards . 7
9 7 Classification . 7
10 8 Marking and instructions . 7
11 9 Protection against access to live parts . 8
12 10 Starting . 8
13 11 Input and current . 8
14 12 Heating . 9
15 13 Resistance to heat and fire . 9
16 14 Moisture resistance . 9
17 15 Resistance to rusting . 9
18 16 Overload protection of transformers and associated circuits . 9
19 17 Endurance . 9
20 18 Abnormal operation . 9
21 19 Mechanical hazards . 10
22 20 Mechanical strength . 13
23 21 Construction . 13
24 22 Internal wiring . 13
25 23 Components . 14
26 24 Supply connection and external flexible cables and cords . 14
27 25 Terminals for external conductors . 14
28 26 Provision for earthing . 14
29 27 Screws and connections . 14
30 28 Creepage distances, clearances and distances through insulation . 14
31 Annexes . 15
32 Annex I (informative) Measurement of noise and vibration emissions . 15
33 Annex K (normative) Battery tools and battery packs . 16
34 Annex L (normative) Battery tools and battery packs provided with mains connection
35 or non-isolated sources . 17
36 Bibliography . 18
38 Figure 101 – Example of a belt disc sander. 6
39 Figure 102 – Rod test and ball for the in-feed nip between the belt and roller . 11
40 Figure 103 – Steel ball test . 12
42 Table 4 – Required performance levels . 9
oSIST prEN IEC 62841-3-16:2024
IEC CDV 62841-3-16 ED1 © IEC 2024 2 116/825/CDV
44 INTERNATIONAL ELECTROTECHNICAL COMMISSION
45 ____________
47 ELECTRIC MOTOR-OPERATED HAND-HELD TOOLS, TRANSPORTABLE
48 TOOLS AND LAWN AND GARDEN MACHINERY – SAFETY –
50 Part 3-16: Particular requirements for transportable belt sanders, disc
51 sanders and belt/disc sanders
53 FOREWORD
54 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
55 all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
56 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
57 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
58 Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
59 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
60 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
61 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
62 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
63 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
64 consensus of opinion on the relevant subjects since each technical committee has representation from all
65 interested IEC National Committees.
66 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
67 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of
68 IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
69 misinterpretation by any end user.
70 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
71 transparently to the maximum extent possible in their national and regional publications. Any divergence between
72 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
73 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
74 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
75 services carried out by independent certification bodies.
76 6) All users should ensure that they have the latest edition of this publication.
77 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
78 members of its technical committees and IEC National Committees for any personal injury, property damage or
79 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
80 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other
81 IEC Publications.
82 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
83 indispensable for the correct application of this publication.
84 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
85 rights. IEC shall not be held responsible for identifying any or all such patent rights.
86 IEC 62841-3-16 has been prepared by IEC technical committee 116: Safety of motor-operated
87 electric tools. It is an International Standard.
88 The text of this International Standard is based on the following documents:
Draft Report on voting
116/XX/FDIS 116/XX/RVD
90 Full information on the voting for its approval can be found in the report on voting indicated in
91 the above table.
92 The language used for the development of this International Standard is English.
93 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
94 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
oSIST prEN IEC 62841-3-16:2024
IEC CDV 62841-3-16 ED1 © IEC 2024 3 116/825/CDV
95 at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
96 described in greater detail at www.iec.ch/standardsdev/publications.
97 This Part 3-16 is to be used in conjunction with the first edition of IEC 62841-1 (2014).
98 This Part 3-16 supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as
99 to convert it into the IEC Standard: Particular requirements for transportable belt sanders, disc
100 sanders and belt/disc sanders.
101 Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-16, that
102 subclause applies as far as relevant. Where this document states "addition", "modification" or
103 "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly.
104 The following print types are used:
105 – requirements: in roman type;
106 – test specifications: in italic type;
107 – notes: in small roman type.
108 The terms defined in Clause 3 are printed in bold typeface.
109 Subclauses, notes, tables and figures which are additional to those in IEC 62841-1:2014,
110 except as described for Annex K and Annex L below, are numbered starting from 101.
111 Subclauses, notes, tables and figures in Annex K and Annex L which are additional to those in
112 the main body of this document are numbered starting from 301.
113 A list of all parts of the IEC 62841 series, under the general title: Electric motor-operated hand-
114 held tools, transportable tools and lawn and garden machinery – Safety, can be found on the
115 IEC website.
116 The committee has decided that the contents of this document will remain unchanged until the
117 stability date indicated on the IEC website under webstore.iec.ch in the data related to the
118 specific document. At this date, the document will be
119 • reconfirmed,
120 • withdrawn,
121 • replaced by a revised edition, or
122 • amended.
123 NOTE The attention of National Committees is drawn to the fact that equipment manufacturers
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.