EN 61326-2-5:2006
(Main)Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2
Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2
treats the particular features for EMC testing of field devices with interfaces according to IEC 61784-1, CP 3/2. This part of IEC 61326 covers only the field-bus interface of the equipment. traite les aspects particuliers des essais CEM pour les dispositifs ayant des interfaces conformes à la CEI 61784-1, CP 3/2.
Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen --Teil 2-5: Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte mit Schnittstellen gemäß IEC 61784-1, CP 3/2
Matériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM - Partie 2-5: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les dispositifs en exploitation avec des interfaces conformes à la CEI 61784-1, CP 3/2
traite les aspects particuliers des essais CEM pour les dispositifs ayant des interfaces conformes à la CEI 61784-1, CP 3/2. Cette partie de la CEI 61326 couvre uniquement les interfaces des bus de terrain de l'équipement.
Električna oprema za merjenje, krmiljenje in laboratorijsko uporabo - Zahteve za elektromagnetno združljivost (EMC) - 2-5. del: Posebne zahteve - Preskusne konfiguracije, obratovalni pogoji in merila za lastnosti terenskih naprav z vmesnikom po IEC 61784-1, CP 3/2 (IEC 61326-2-5:2006)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electrical equipment for measurement, control and laboratory use - EMC requirements -- Part 2-5: Particular requirements - Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/23UHVNXVQHMatériel électrique de mesure, de commande et de laboratoire - Exigences relatives à la CEM -- Partie 2-5: Exigences particulières - Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les dispositifs en exploitation avec des interfaces conformes à la CEI 61784-1, CP 3/2Elektrische Mess-, Steuer-, Regel- und Laborgeräte - EMV-Anforderungen --Teil 2-5: Besondere Anforderungen - Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte mit Schnittstellen gemäß IEC 61784-1, CP 3/2Ta slovenski standard je istoveten z:EN 61326-2-5:2006SIST EN 61326-2-5:2007en33.100.0125.040.40ICS:SLOVENSKI
STANDARDSIST EN 61326-2-5:200701-januar-2007
EUROPEAN STANDARD EN 61326-2-5 NORME EUROPÉENNE
EUROPÄISCHE NORM October 2006
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61326-2-5:2006 E
ICS 25.040.40; 33.100 Supersedes EN 61326:1997 + A1:1998 + A2:2001 + A3:2003
English version
Electrical equipment for measurement, control and laboratory use -
EMC requirements -
Part 2-5: Particular requirements -
Test configurations, operational conditions and performance criteria
for field devices with interfaces according to IEC 61784-1, CP 3/2 (IEC 61326-2-5:2006)
Matériel électrique de mesure,
de commande et de laboratoire -
Exigences relatives à la CEM -
Partie 2-5: Exigences particulières -
Configurations d'essai, conditions
de fonctionnement et critères d'aptitude
à la fonction pour les dispositifs
en exploitation avec des interfaces conformes à la CEI 61784-1, CP 3/2 (CEI 61326-2-5:2006)
Elektrische Mess-, Steuer-, Regel-
und Laborgeräte -
EMV-Anforderungen
Teil 2-5: Besondere Anforderungen -
Prüfanordnungen, Betriebsbedingungen und Leistungsmerkmale für Feldgeräte
mit Schnittstellen gemäß IEC 61784-1,
CP 3/2 (IEC 61326-2-5:2006)
This European Standard was approved by CENELEC on 2006-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
- 2 -
Foreword The text of document 65A/474/FDIS, future edition 1 of IEC 61326-2-5, prepared by SC 65A, System aspects, of IEC TC 65, Industrial-process measurement and control, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61326-2-5 on 2006-09-01. The EN 61326 series supersedes EN 61326:1997 + corrigendum September 1998 + A1:1998 + A2:2001 + A3:2003. This part of EN 61326 is to be used in conjunction with EN 61326-1 and follows the same numbering of clauses, subclauses, tables and figures as that standard. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2007-06-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2009-09-01 This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and covers essential requirements of EC Directive 89/336/EEC. See Annex ZZ. Annexes ZA and ZZ have been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 61326-2-5:2006 was approved by CENELEC as a European Standard without any modification. __________
- 3 - EN 61326-2-5:2006 Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year Addition to Annex ZA of EN 61326-1:2006:
IEC 61326-1 2005 Electrical equipment for measurement, control and laboratory use - EMC requirements
Part 1: General requirements EN 61326-1 2006
IEC 61158
Series Digital data communication for measurement and control - Fieldbus for use in industrial control systems EN 61158 Series
IEC 61158-2 - 1) Digital data communications for measurement and control - Fieldbus for use in industrial control systems
Part 2: Physical layer specification and service definition EN 61158-2 2004 2)
IEC 61158-3 - 1) Digital data communication for measurement and control - Fieldbus for use in industrial control systems
Part 3: Data link service definition EN 61158-3 2004 2)
IEC 61158-5
- 1) Digital data communication for measurement and control - Fieldbus for use in industrial control systems
Part 5: Application layer service definition EN 61158-5 2004 2)
IEC 61158-6
- 1) Digital data communication for measurement and control - Fieldbus for use in industrial control systems
Part 6: Application layer protocol specificationEN 61158-6 2004 2)
IEC 61784
Series Digital data communications for measurement and control EN 61784
Series
IEC 61784-1
- 1) Digital data communications for measurement and control
Part 1: Profile sets for continuous and discrete manufacturing relative to fieldbus use in industrial control systems EN 61784-1 + corr. December
2004 2)2004
1) Undated reference.
2) Valid edition at date of issue.
- 4 - Annex ZZ (informative)
Coverage of Essential Requirements of EC Directives This European Standard has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association and within its scope the standard covers all relevant essential requirements as given in Article 4 of the EC Directive 89/336/EEC. Compliance with this standard provides one means of conformity with the specified essential requirements of the Directive concerned. WARNING: Other requirements and other EC Directives may be applicable to the products falling within the scope of this standard. ___________
NORME INTERNATIONALECEIIEC INTERNATIONAL STANDARD 61326-2-5Première éditionFirst edition2006-06 Matériel électrique de mesure, de commande et de laboratoire – Exigences relatives à la CEM – Partie 2-5: Exigences particulières – Configurations d'essai, conditions de fonctionnement et critères d'aptitude à la fonction pour les dispositifs en exploitation avec des interfaces conformes à la CEI 61784-1, CP 3/2
Electrical equipment for measurement, control
and laboratory use – EMC requirements – Part 2-5: Particular requirements – Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2
Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2006
Droits de reproduction réservés
Copyright - all rights reserved Aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l'éditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch CODE PRIX PRICE CODE J Commission Electrotechnique InternationaleInternational Electrotechnical Commission
61326-2-5 IEC:2006 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
ELECTRICAL EQUIPMENT FOR MEASUREMENT,
CONTROL AND LABORATORY USE – EMC REQUIREMENTS –
Part 2-5: Particular requirements – Test configurations,
operational conditions and performance criteria for field devices
with interfaces according to IEC 61784-1, CP 3/2
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61326-2-5 has been prepared by subcommittee 65A: System aspects, of IEC technical committee 65: Industrial-process measurement and control. The IEC 61326 series cancels and replaces IEC 61326:2002 and constitutes a technical revision.
61326-2-5 IEC:2006 – 5 –
The text of this standard is based on the following documents: FDIS Report on voting 65A/474/FDIS 645A/479/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part of IEC 61326 is to be used in conjunction with IEC 61326-1 and follows the same numbering of clauses, subclauses, tables and figures as that standard. IEC 61326 consists of the following parts, under the general title Electrical equipment for measurement, control and laboratory use – EMC requirements: Part 1:
General requirements
Part 2-1:
Particular requirements – Test configurations, operational conditions and performance criteria for sensitive test and measurement equipment for EMC unprotected applications
Part 2-2:
Particular requirements – Test configurations, operational conditions and performance criteria for portable test, measuring and monitoring equipment used in low-voltage distribution systems
Part 2-3:
Particular requirements – Test configuration, operational conditions and performance criteria for transducers with integrated or remote signal conditioning
Part 2-4:
Particular requirements – Test configurations, operational conditions and performance criteria for insulation monitoring devices according to IEC 61557-8 and for equipment for insulation fault location according to IEC 61557-9 Part 2-5:
Particular requirements – Test configurations, operational conditions and performance criteria for field devices with interfaces according to IEC 61784-1, CP 3/2 Part 2-6:
Particular requirements – In vitro diagnostic (IVD) medical equipment Part 3-1:
Immunity requirements for equipment performing or intended to perform safety-related functions (functional safety) – General industrial applications The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed; • withdrawn; • replaced by a revised edition, or • amended.
61326-2-5 IEC:2006 – 7 –
E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.