EN 60512-8-1:2010
(Main)Connectors for electronic equipment - Tests and measurements - Part 8-1: Static load tests (fixed connectors) - Test 8a: Static load, transverse
Connectors for electronic equipment - Tests and measurements - Part 8-1: Static load tests (fixed connectors) - Test 8a: Static load, transverse
IEC 60512-8-1:2010 when required by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard test method to assess the suitability of a fixed connector for use in applications where it may be subject to transverse stresses.
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 8-1: Prüfungen mit statischer Last (feste Steckverbinder) - Prüfung 8a: Statische Querlast
Connecteurs pour équipements électroniques - Essais et mesures - Partie 8-1: Essais sous charge statique (embases) - Essai 8a: Charge statique transversale
La CEI 60512-8-1:2010 est utilisée pour les essais des connecteurs du domaine d'activité du comité d'études 48, lorsque la spécification particulière l'exige. Elle peut également être utilisée pour des dispositifs similaires lorsqu'une spécification particulière le stipule. L'objet de cette norme est de définir une méthode d'essai normalisée pour évaluer l'aptitude d'une embase à être utilisée dans des applications dans lesquelles elle est susceptible de subir des contraintes transversales.
Konektorji za elektronsko opremo - Preskusi in meritve - 8-1. del: Preskusi statične obremenitve (fiksni konektorji) - Preskus 8a: Statična obremenitev, prečna (IEC 60512-8-1:2010)
Ta del IEC 60512 se, kadar ga zahteva podrobna specifikacija, uporablja za preskušanje konektorjev v okviru tehničnega odbora 48. Lahko se uporablja tudi za podobne naprave, kadar ga določa podrobna specifikacija. Cilj tega standarda je podrobno opisati standardno preskusno metodo za ocenjevanje primernosti fiksnega konektorja za uporabo v aplikacijah, pri katerih je lahko izpostavljen prečnim obremenitvam.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2010
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO3UHVNXVLVWDWLþQH
REUHPHQLWYHILNVQLNRQHNWRUML3UHVNXVD6WDWLþQDREUHPHQLWHYSUHþQD,(&
Connectors for electronic equipment - Tests and measurements - Part 8-1: Static load
tests (fixed connectors) - Test 8a: Static load, transverse (IEC 60512-8-1:2010)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 8-1:
Prüfungen mit statischer Last (feste Steckverbinder) - Prüfung 8a: Statische Querlast
(IEC 60512-8-1:2010)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 8-1: Essais
sous charge statique (embases) - Essai 8a: Charge statique transversale (CEI 60512-8-
1:2010)
Ta slovenski standard je istoveten z: EN 60512-8-1:2010
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60512-8-1
NORME EUROPÉENNE
September 2010
EUROPÄISCHE NORM
ICS 31.220.01
English version
Connectors for electronic equipment -
Tests and measurements -
Part 8-1: Static load tests (fixed connectors) -
Test 8a: Static load, transverse
(IEC 60512-8-1:2010)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Essais et mesures - Einrichtungen - Mess- und Prüfverfahren -
Partie 8-1: Essais sous charge statique Teil 8-1: Prüfungen mit statischer Last
(embases) - (feste Steckverbinder) -
Essai 8a: Charge statique transversale Prüfung 8a: Statische Querlast
(CEI 60512-8-1:2010) (IEC 60512-8-1:2010)
This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-8-1:2010 E
Foreword
The text of document 48B/2154/FDIS, future edition 1 of IEC 60512-8-1, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-8-1 on 2010-09-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-8-1:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60512-8-1:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60512-1-1 - Connectors for electronic equipment - Tests EN 60512-1-1 -
and measurements -
Part 1-1: General examination - Test 1a:
Visual examination
IEC 60512-8-1 ®
Edition 1.0 2010-06
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Tests and measurements –
Part 8-1: Static load tests (fixed connectors) – Test 8a: Static load, transverse
Connecteurs pour équipements électroniques – Essais et mesures –
Partie 8-1: Essais sous charge statique (embases) – Essai 8a: Charge statique
transversale
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
E
CODE PRIX
ICS 31.220.01 ISBN 978-2-88910-951-7
– 2 – 60512-8-1 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
CONNECTORS FOR ELECTRONIC EQUIPMENT –
TESTS AND MEASUREMENTS –
Part 8-1: Static load tests (fixed connectors) –
Test 8a: Static load, transverse
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Availab
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.