Connectors for electronic equipment - Tests and measurements - Part 17-2: Cable clamping tests - Test 17b: Cable clamp resistance to cable rotation

IEC 60512-17-2:2011 when required by the detail specification, is used for testing connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this standard is to detail a standard method to assess the ability of a cable-clamping device to allow rotary movement of the cable/wire bundle without damage to the external surface of the cable/wire bundle, the cable-clamping device, the connector or the sub-assembly. This standard cancels and replaces Test 17b of IEC 60512-5, issued in 1992, and constitutes a technical revision. This publication is to be read in conjunction with  IEC 60512-1:2001 and IEC 60512-1-100:2006.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 17-2: Prüfungen der Kabelabfangung - Prüfung 17b: Kabelabfangung, Sicherheit gegen Einschneiden des Kabelmantels

Connecteurs pour équipements électroniques – Essais et mesures – Partie 17-2: Essais de pincement de câble – Essai 17b: Résistance des pinces de maintien des câbles à la rotation des câbles

La CEI 60512-17-2:2011 lorsque la spécification particulière l'exige, est utilisée pour les essais des connecteurs qui entrent dans le domaine d'application du Comité d'Etudes 48 de la CEI. Ces essais peuvent aussi être utilisés sur des composants similaires lorsqu'une spécification particulière le précise. L'objet du présent norme est de définir une méthode normalisée pour évaluer l'aptitude d'un dispositif de pincement de câble à permettre un mouvement de rotation du faisceau de câbles/fils sans endommager la surface externe du faisceau de câbles/fils, le dispositif de pincement, le connecteur ou le sous-ensemble. La présente norme annule et remplace l'Essai 17b de la CEI 60512-9, publiée en 1992. Elle constitue une révision technique. Cette publication doit être lue conjointement avec la CEI 60512-1:2001 et la CEI 60512-1-100:2006.

Konektorji za elektronsko opremo - Preskusi in meritve - 17-2. del: Preskušanje kabelskih objemk - Preskus 17b: Odpornost kabelskih objemk proti obračanju kabla

Ta del IEC 60512 se, kadar ga zahteva podrobna specifikacija, uporablja za preskušanje konektorjev v okviru tehničnega odbora 48. Lahko se uporablja tudi za podobne naprave, kadar ga določa podrobna specifikacija.
Cilj tega standarda je podrobno opisati standardno metodo za ocenitev zmožnosti naprave s kabelskimi objemkami, da omogoča rotacijsko gibanje snopa kablov/žic brez poškodbe zunanje površine snopa kablov/žic, naprave s kabelskimi objemkami, konektorja ali podsklopa.

General Information

Status
Published
Publication Date
09-Jun-2011
Withdrawal Date
11-May-2014
Technical Committee
Drafting Committee
Parallel Committee
Current Stage
6060 - Document made available - Publishing
Start Date
10-Jun-2011
Completion Date
10-Jun-2011

Buy Standard

Standard
EN 60512-17-2:2011
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2011
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO3UHVNXãDQMH
NDEHOVNLKREMHPN3UHVNXVE2GSRUQRVWNDEHOVNLKREMHPNSURWLREUDþDQMX
NDEOD
Connectors for electronic equipment - Tests and measurements - Part 17-2: Cable
clamping tests - Test 17b: Cable clamp resistance to cable rotation
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren -- Teil 17-2:
Prüfungen der Kabelabfangung - Prüfung 17b: Kabelabfangung, Sicherheit gegen
Einschneiden des Kabelmantels
&RQQHFWHXUVSRXUpTXLSHPHQWVpOHFWURQLTXHV±(VVDLVHWPHVXUHV±3DUWLH(VVDLV
GHSLQFHPHQWGHFkEOH±(VVDLE5pVLVWDQFHGHVSLQFHV
GHPDLQWLHQGHVFkEOHVjODURWDWLRQGHVFkEOHV
Ta slovenski standard je istoveten z: EN 60512-17-2:2011
ICS:
21.060.70 Sponke in skobe Clamps and staples
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60512-17-2
NORME EUROPÉENNE
June 2011
EUROPÄISCHE NORM
ICS 31.220.01
English version
Connectors for electronic equipment -
Tests and measurements -
Part 17-2: Cable clamping tests -
Test 17b: Cable clamp resistance to cable rotation
(IEC 60512-17-2:2011)
Connecteurs pour équipements Steckverbinder für elektronische
électroniques – Essais et mesures – Einrichtungen -
Partie 17-2: Essais de pincement de câble Mess- und Prüfverfahren -
– Essai 17b: Résistance des pinces de Teil 17-2: Prüfungen der Kabelabfangung
maintien des câbles à la rotation des -
câbles Prüfung 17b: Kabelabfangung, Sicherheit
(CEI 60512-17-2:2011) gegen Einschneiden des Kabelmantels
(IEC 60512-17-2:2011)
This European Standard was approved by CENELEC on 2011-05-12. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-17-2:2011 E
Foreword
The text of document 48B/2124/CDV, future edition 1 of IEC 60512-17-2, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-17-2 on 2011-05-12.
This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100, which explains the
structure of the EN 60512 series.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2012-02-12
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2014-05-12
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-17-2:2011 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 60512-17-2:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60512-1 - Connectors for electronic equipment - Tests EN 60512-1 -
and measurements -
Part 1: General
IEC 60512-1-1 - Connectors for electronic equipment - Tests EN 60512-1-1 -
and measurements -
Part 1-1: General examination - Test 1a:
Visual examination
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 -
and measurements -
Part 1-100: General - Applicable publications

IEC 60512-17-2 ®
Edition 1.0 2011-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Connectors for electronic equipment – Tests and measurements –
Part 17-2: Cable clamping tests – Test 17b: Cable clamp resistance to cable
rotation
Connecteurs pour équipements électroniques – Essais et mesures –
Partie 17-2: Essais de pincement de câble – Essai 17b: Résistance des pinces
de maintien des câbles à la rotation des câbles
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX F
ICS 31.220.01 ISBN 978-2-88912-448-0

– 2 – 60512-17-2  IEC:2011
CONTENTS
FOREWORD . 3
1 Scope and object . 5
2 Normative references . 5
3 Preparation of the specimen . 5
4 Test method . 5
5 Final measurements . 6
6 Requirements . 6
7 Details to be specified . 6

Figure 1 – Cable test set-up . 6

60512-17-2  IEC
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.