EN 50632-2-22:2015/A1:2021

Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular requirements for cut-off machines and wall chasers

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for cut-off machines and wall chasers.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-22: Besondere Anforderungen für Trennschleifmaschinen und Wandschlitzfräsen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-22: Exigences particulières pour les tronçonneuses

Elektromotorna orodja - Postopek meritve prahu - 2-22. del: Posebne zahteve za rezalne stroje in rezalnike zidnih utorov - Dopolnilo A1

Ta točka 1. dela se ne uporablja v naslednjih primerih: ta del standarda EN 50632 velja za rezalnike in zidne rezkarje.

General Information

• Status: Published
• Publication Date: 23-Dec-2021
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: CLC/TC 116/WG 04 - Dust
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 24-Dec-2021
• Due Date: 09-Aug-2022
• Completion Date: 24-Dec-2021
• Ref Project: SIST EN 50632-2-22:2015/A1:2022 - Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular requirements for cut-off machines and wall chasers

Relations

• Amends: EN 50632-2-22:2015 - Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular requirements for cut-off machines and wall chasers
• Effective Date: 25-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2022
Elektromotorna orodja - Postopek meritve prahu - 2-22. del: Posebne zahteve za
rezalne stroje in rezalnike zidnih utorov - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-22: Particular
requirements for cut-off machines and wall chasers
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-22: Besondere
Anforderungen für Trennschleifmaschinen und Wandschlitzfräsen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-22:
Exigences particulières pour les tronçonneuses
Ta slovenski standard je istoveten z: EN 50632-2-22:2015/A1:2021
ICS:
25.100.01 Rezalna orodja na splošno Cutting tools in general
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-22:2015/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2021
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-22: Particular requirements for cut-off machines and wall
chasers
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-22: Exigences particulières pour les Teil 2-22: Besondere Anforderungen für
tronçonneuses Trennschleifmaschinen und Wandschlitzfräsen
This amendment A1 modifies the European Standard EN 50632-2-22:2015; it was approved by CENELEC on 2021-12-07. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-22:2015/A1:2021 E

Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modifications to 4.3, “Operating conditions” . 4
3 Modifications to Figures 101 and 102 . 6

European foreword
This document (EN 50632-2-22:2015/A1:2021) has been prepared by CLC/TC 116 “Safety and environmental
aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-12-07
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-12-07
conflicting with this document have to be
withdrawn
This amendment was developed to include improvements and clarifications suggested by practical tests.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found on the CENELEC website.
1 Modification to the European foreword
th
Replace the 5 paragraph with the following:
“This Part 2 is to be used in conjunction with EN 50632-1:2015 and its amendments.”
2 Modifications to 4.3, “Operating conditions”
Replace the existing Table 101 with the following:
“
Table 101 — Operating conditions for cut-off machines
Material and set- Concrete slabs with minimum dimensions of 400 mm x 400 mm, maximum
up dimensions of 600 mm x 600 mm and a thickness of (50 ± 5) mm according to
EN 1339:2003. The concrete slabs shall be stored for at least six weeks with the last
three weeks under dry conditions. During storing, the distance between the slabs shall
be at least one slab thickness. The slabs shall have the following specificati
...