Specifications for particular types of winding wires - Part 89: Polyesterimide enamelled round aluminum wire, class 200

IEC 60317-89:2023 specifies the requirements of enamelled round aluminium winding wire of class 200 with a sole coating based on polyesterimide resin, which can be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one or more additives to enhance certain performance or application characteristics. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,250 mm up to and including 1,600 mm; grade 2: 0,250 mm up to and including 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3:2008 and IEC 60317-0-3:2008/AMD1:2013. This International Standard is to be used in conjunction with IEC 60317-0-3:2008, its Amendment 1 (2013) and its Amendment 2 (2019).

Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten Teil 89: Runddrähte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 200

Spécifications pour types particuliers de fils de bobinage - Partie 89: Fil de section circulaire en aluminium émaillé au polyestérimide, classe 200

IEC 60317-89-2023 spécifie les exigences relatives aux fils de bobinage de section circulaire en aluminium émaillé de classe 200, avec un revêtement simple à base de résine polyestérimide, qui peut être modifiée sous réserve qu'elle conserve l'identité chimique de la résine initiale et respecte l'ensemble des exigences spécifiées du fil. NOTE Une résine modifiée est une résine dont les propriétés chimiques ont été modifiées, ou qui contient un ou plusieurs additifs visant à améliorer certaines performances ou caractéristiques d’application. La gamme des diamètres nominaux des conducteurs couverte par la présente norme est: grade 1: de 0,250 mm jusqu’à 1,600 mm (inclus); grade 2: de 0,250 mm jusqu’à 5,000 mm (inclus). Les diamètres nominaux des conducteurs sont spécifiés à l’Article 4 de l’IEC 60317-0-3:2008 et de l’IEC 60317-0-3:2008/AMD1:2013. La présente Norme internationale doit être utilisée conjointement avec l'IEC 60317-0-3:2008, son Amendement 1 (2013) et son Amendement 2 (2019).

Specifikacije za posebne vrste navijalnih žic - 89. del: Okrogla aluminijeva žica, lakirana s poliesterimidnim lakom, razred 200 (IEC 60317-89:2023)

General Information

Status
Published
Publication Date
14-Sep-2023
Technical Committee
Drafting Committee
Current Stage
6060 - Document made available - Publishing
Start Date
15-Sep-2023
Due Date
28-Jul-2023
Completion Date
15-Sep-2023

Buy Standard

Draft
prEN IEC 60317-89:2023
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN IEC 60317-89:2023
01-marec-2023
Specifikacije za posebne vrste navijalnih žic - 89. del: Okrogla aluminijeva žica,
lakirana s poliesterimidnim lakom, razred 200
Specifications for particular types of winding wires - Part 89: Polyesterimide enameled
round aluminum wire, class 200
Ta slovenski standard je istoveten z: prEN IEC 60317-89:2023
ICS:
29.060.10 Žice Wires
77.150.10 Aluminijski izdelki Aluminium products
oSIST prEN IEC 60317-89:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 60317-89:2023

---------------------- Page: 2 ----------------------
oSIST prEN IEC 60317-89:2023
55/1939/CDV
COMMITTEE DRAFT FOR VOTE (CDV)

PROJECT NUMBER:
IEC 60317-89 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-01-20 2023-04-14
SUPERSEDES DOCUMENTS:
55/1925/CD, 55/1934/CC

IEC TC 55 : WINDING WIRES
SECRETARIAT: SECRETARY:
United States of America Mr Mike Leibowitz
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:

TC 2
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of
• any relevant patent rights of which they are aware and to provide supporting documentation,
• any relevant “in some countries” clauses to be included should this proposal proceed. Recipients are
reminded that the enquiry stage is the final stage for submitting "in some countries" clauses. See
AC/22/2007.

TITLE:
Specifications for particular types of winding wires - Part 89: Polyesterimide enameled round
aluminum wire, class 200

PROPOSED STABILITY DATE: 2025

NOTE FROM TC/SC OFFICERS:


Copyright © 2022 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it, for
any other purpose without permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN IEC 60317-89:2023
IEC CDV 60317-89/Ed1 © IEC:2023 – 2 – 55/1939/CDV
1 CONTENTS
2 FOREWORD .3
3 INTRODUCTION .5
4 1 Scope . 6
5 2 Normative references . 6
6 3 Terms, definitions and general notes on methods of test and appearance . 6
7 3.1 Terms and definitions . 6
8 3.2 General notes . 7
9 3.2.1 Methods of test . 7
10 3.2.2 Winding wire . 7
11 3.3 Appearance . 7
12 4 Dimensions . 7
13 5 Electrical resistance . 7
14 6 Elongation . 7
15 7 Springiness . 7
16 8 Flexibility and adherence . 7
17 9 Heat shock .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.