FprEN IEC 61347-2-13:2024
(Main)Controlgear for electric light sources - Safety - Part 2-13: Particular requirements - Electronic controlgear for LED light sources
Controlgear for electric light sources - Safety - Part 2-13: Particular requirements - Electronic controlgear for LED light sources
IEC 61347-2-13:2024 specifies safety requirements for electronic controlgear for LED light sources for use on DC supplies up to 1 500 V or on AC supplies up to 1 000 V at 50 Hz or 60 Hz. This document is applicable for electronic controlgear for LED light sources with an output voltage (RMS) not higher than 1 000 V. This third edition cancels and replaces the second edition published in 2014 and Amendment 1:2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) alignment with respect to the fourth edition of IEC 61347-1: - introduction of dated references to the fourth edition of IEC 61347-1 as appropriate; - deletion of the clauses and subclauses which are either no longer relevant or now covered in IEC 61347-1; b) update of normative references, introducing dated references where appropriate; c) scope extension to 1 500 V for direct current; d) scope clarification; e) deletion of unused definitions; f) revision of information and marking requirements; g) new marking requirement "electronic controlgear for LED light sources"; h) new requirements for electronic controlgear for LED light sources with constant light output function or programmable current (additions to Clause 3, Clause 6, Clause 16 and Clause 18); i) modification of requirements for the determination of the output working voltage (new Clause 17); j) new requirements for the determination of the rated output characteristics (Clause 18).
Betriebsgeräte für elektrische Lichtquellen - Sicherheit - Teil 2-13: Besondere Anforderungen an elektronische Betriebsgeräte für LED-Lichtquellen
Appareillages de commande pour les sources de lumière électriques - Sécurité - Partie 2-13 : Exigences particulières - Appareillages électroniques pour les sources de lumière à LED
L'IEC 61347-2-13:2024 spécifie des exigences de sécurité pour les appareillages électroniques des sources de lumière électriques à LED qui sont destinés à être utilisés sur des alimentations de courant continu jusqu'à 1 500 V ou sur des alimentations de courant alternatif jusqu'à 1 000 V à 50 Hz ou 60 Hz. Le présent document s'applique aux appareillages électroniques pour les sources de lumière à LED de tension de sortie (valeur efficace) ne dépassant pas 1 000 V. Cette troisième édition annule et remplace la deuxième édition parue en 2014 et son Amendement 1:2016. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) alignement sur la quatrième édition de l’IEC 61347-1: - ajout de références datées à la quatrième édition de l'IEC 61347-1 lorsque cela est approprié; - suppression des articles et paragraphes qui soit ne sont plus pertinents soit ne sont plus couverts par l'IEC 61347-1; b) mise à jour des références normatives, ajout de références normatives lorsque cela est approprié; c) extension du domaine d'application à 1 500 V pour le courant continu; d) clarification du domaine d'application; e) suppression des définitions qui ne sont pas utilisées; f) révision des exigences d'informations et de marquage; g) nouvelle exigence de marquage "appareillage électronique pour sources de lumière à LED"; h) nouvelles exigences pour les appareillages électroniques pour les sources de lumière à LED avec fonction de flux lumineux constant ou à courant programmable (ajouts aux Articles 3, 6, 16 et 18); i) modification des exigences pour la détermination de la tension de service de sortie (nouvel Article 17); j) nouvelles exigences pour la détermination des caractéristiques de sortie assignées (Article 18).
Stikalne naprave za sijalke - Varnost - 2-13. del: Posebne zahteve za elektronske stikalne naprave za LED-svetlobne vire
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN IEC 61347-2-13:2023
01-junij-2023
Stikalne naprave za sijalke - Varnost - 2-13. del: Posebne zahteve za elektronske
stikalne naprave za LED-svetlobne vire
Controlgear for electric light sources - Safety - Part 2-13: Particular requirements for
electronic controlgear for LED light sources
Geräte für Lampen - Teil 2-13: Besondere Anforderungen an gleich- oder
wechselstromversorgte elektronische Betriebsgeräte für LED-Module
Appareillage de lampes - Partie 2-13: Exigences particulières pour les appareillages
électroniques alimentés en courant continu ou en courant alternatif pour modules de
LED
Ta slovenski standard je istoveten z: prEN IEC 61347-2-13:2023
ICS:
29.130.01 Stikalne in krmilne naprave Switchgear and controlgear
na splošno in general
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
oSIST prEN IEC 61347-2-13:2023 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN IEC 61347-2-13:2023
oSIST prEN IEC 61347-2-13:2023
34C/1576/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61347-2-13 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-03-31 2023-06-23
SUPERSEDES DOCUMENTS:
34C/1553/CD, 34C/1561A/CC
IEC SC 34C : AUXILIARIES FOR LAMPS
SECRETARIAT: SECRETARY:
United Kingdom Mr Petar Luzajic
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
A
Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of
• any relevant patent rights of which they are aware and to provide supporting documentation ,
• any relevant “in some countries” clauses to be included should this proposal proceed. Recipients are
reminded that the enquiry stage is the final stage for submitting "in some countries" clauses. See
AC/22/2007.
TITLE:
Controlgear for electric light sources - Safety - Part 2-13: Particular requirements for electronic
controlgear for LED light sources
PROPOSED STABILITY DATE: 2027
NOTE FROM TC/SC OFFICERS:
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it, for
any other purpose without permission in writing from IEC.
oSIST prEN IEC 61347-2-13:2023
IEC CDV 61347-2-13 © IEC 2023 2 34C/1576/CDV
1 CONTENTS
2 CONTENTS . 2
3 FOREWORD . 3
4 1 Scope . 6
5 2 Normative references. 6
6 3 Terms and definitions . 6
7 4 General requirements . 7
8 5 General notes on tests . 8
9 6 Information and marking . 8
10 6.1 Marking and information . 8
11 6.1.1 Mandatory markings . 8
12 6.1.2 Information to be provided . 8
13 6.2 Durability and legibility of marking . 8
14 6.3 Built-in and integral controlgear . 9
15 7 Terminals . 9
16 8 Earthing . 9
17 9 Protection against accidental contact with hazardous live parts . 9
18 10 Insulation resistance and electric strength . 9
19 11 Fault Conditions . 9
20 12 Construction . 9
21 13 Creepage distances, clearances and distances through insulation . 9
22 14 Screws, current-carrying parts and connections . 9
23 15 Resistance to heat, fire and tracking . 9
24 16 Thermal requirements for controlgear . 10
25 16.1 General . 10
26 16.2 Normal operation . 10
27 16.3 Abnormal operation . 10
28 17 Output working voltage (Uout) . 10
29 18 Rated output characteristics . 11
30 Annex A (normative) Additional requirements for centrally supplied controlgear for
31 emergency lighting . 12
32 A.1 Marking and information . 12
33 A.2 General notes on tests . 12
34 A.3 Operating condition . 12
35 A.4 Supply current . 12
36 A.5 EMC immunity . 13
37 A.6 Pulse voltage from central battery systems . 13
38 A.7 Tests for abnormal conditions . 13
39 A.8 Temperature cycling test and endurance test . 13
40 A.9 Functional safety (EOF ) . 13
x
41 Annex B (informative) Schedule of more onerous requirements . 15
42 Bibliography . 16
44 Table A.1 – Pulse voltages . 13
oSIST prEN IEC 61347-2-13:2023
IEC CDV 61347-2-13 © IEC 2023 3 34C/1576/CDV
46 INTERNATIONAL ELECTROTECHNICAL COMMISSION
47 ____________
49 CONTROLGEAR FOR ELECTRIC LIGHT SOURCES – SAFETY
51 Part 2-13: Particular requirements for
52 electronic controlgear for LED light sources
54 FOREWORD
55 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
56 all national electrotechnical committees (IEC National Committees). The object of IEC i s to promote international
57 co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
58 in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
59 Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
60 preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
61 may participate in this preparatory work. International, governmental and non-governmental organizations liaising
62 with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
63 Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
64 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
65 consensus of opinion on the relevant subjects since each technical committee has representatio n from all
66 interested IEC National Committees.
67 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
68 Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
69 Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
70 misinterpretation by any end user.
71 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
72 transparently to the maximum extent possible in their national and regional publications. Any divergence between
73 any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
74 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
75 assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
76 services carried out by independent certification bodies.
77 6) All users should ensure that they have the latest edition of this publication.
78 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
79 members of its technical committees and IEC National Committees for any personal injury, property damage or
80 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
81 expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
82 Publications.
83 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
84 indispensable for the correct application of this publication.
85 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
86 rights. IEC shall not be held responsible for identifying any or all such patent rights.
87 IEC 61347-2-13 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC
88 technical committee 34: Lighting.
89 This third edition cancels and replaces the second edition published in 2014 and Amendment 1
90 (2016). This edition constitutes a technical revision.
oSIST prEN IEC 61347-2-13:2023
IEC CDV 61347-2-13 © IEC 2023 4 34C/1576/CDV
92 This edition includes the following significant technical changes with respect to the previous
93 edition:
94 a) changes in IEC 61347-1 (see ED 4 of IEC 61347-1)
95 b) alignment with respect to edition 4 of IEC 61347-1:
96 – introduction of dated references as appropriate
97 – deletion of the clauses/subclauses which are either no longer relevant or now covered
98 in part 1
99 c) update of normative references, introducing dated references where appropriate
100 d) scope extension to 1 500 V for DC
101 e) scope clarification
102 f) deletion of unused definitions
103 g) revision of information and marking requirements
104 h) new Marking requirement “LED controlgear”
105 i) new requirements for LED controlgear with constant light output function or programmable
106 current (additions to clauses 3, 6, 13 and 19)
107 j) additional touch current requirements under fault conditions (clause 12)
108 k) addition of requirements for the determination of the output working voltage (new Clause 18)
109 This document is intended to be used in conjunction with IEC 61347-1. Where the requirements
110 of any of the clauses of IEC 61347-1 are referred to in this document by the phrase
111 "IEC 61347-1, Clause n applies", this phrase is interpreted as meaning that all requirements of
112 the clause in question of IEC 61347-1 apply, except any which are clearly inapplicable to the
113 specific type of controlgear covered by this document.
114 A list of all parts in the IEC 61347, published under the general title Controlgear for electric light
115 sources can be found on the IEC website.
116 The text of this International Standard is based on the following documents:
FDIS Report on voting
34C/____/FDIS 34C/____/RVD
118 Full information on the voting for the approval of this standard can be found in the report on
119 voting indicated in the above table.
120 The language used for the development of this International Standard is English.
121 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
122 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
123 at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.