iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60512-16-14:2008

(Main)

Connectors for electronic equipment - Tests and measurements - Part 16-14: Mechanical tests on contacts and terminations - Test 16n: Bending strength, fixed male tabs

Connectors for electronic equipment - Tests and measurements - Part 16-14: Mechanical tests on contacts and terminations - Test 16n: Bending strength, fixed male tabs

IEC 60512-16-14:2008 details a standard test method to determine the ability of a fixed male tab and its fixing to withstand a specified bending stress. If so specified in the detail specification, forces other than bending may be applied.

Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 16-14: Mechanische Prüfungen an Kontakten und Anschlüssen - Prüfung 16n: Biegefestigkeit von Flachsteckern

Connecteurs pour équipements électroniques - Essais et mesures - Partie 16-14: Essais mécaniques des contacts et des sorties - Essai 16n: Résistance à la flexion des languettes fixes

La CEI 60512-16-14:2008 détaille une méthode d'essai normalisée pour déterminer l'aptitude d'une patte fixe et de sa fixation à résister à une contrainte de flexion spécifiée. Si la spécification particulière le prescrit, des forces autres que la force de flexion peuvent être appliquées.

Konektorji za elektronsko opremo - Preskusi in meritve - 16-14. del: Mehanski preskusi na kontaktih in priključkih - Preskus 16n: Upogibna trdnost, fiksni moški jezički (IEC 60512-16-14:2008)

General Information

Status
Published
Publication Date
18-Sep-2008
Withdrawal Date
31-Jul-2011
ICS
31.220.10 - Plug-and-socket devices. Connectors
Technical Committee
CLC/SR 48B - Connectors
Drafting Committee
IEC/SC 48B - IEC_SC_48B
Parallel Committee
IEC/SC 48B - IEC_SC_48B
Current Stage
6060 - Document made available - Publishing
Start Date
19-Sep-2008
Completion Date
19-Sep-2008
Ref Project
SIST EN 60512-16-14:2008 - Connectors for electronic equipment - Tests and measurements - Part 16-14: Mechanical tests on contacts and terminations - Test 16n: Bending strength, fixed male tabs (IEC 60512-16-14:2008)

Buy Standard

EN 60512-16-14:2008EN 60512-16-14:2008
PreviousNext
Standard
EN 60512-16-14:2008
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60512-16-14:2008
01-december-2008
.RQHNWRUML]DHOHNWURQVNRRSUHPR3UHVNXVLLQPHULWYHGHO0HKDQVNL
SUHVNXVLQDNRQWDNWLKLQSULNOMXþNLK3UHVNXVQ8SRJLEQDWUGQRVWILNVQLPRãNL
MH]LþNL ,(&
Connectors for electronic equipment - Tests and measurements - Part 16-14: Mechanical
tests on contacts and terminations - Test 16n: Bending strength, fixed male tabs (IEC
60512-16-14:2008)
Steckverbinder für elektronische Einrichtungen - Mess- und Prüfverfahren - Teil 16-14:
Mechanische Prüfungen an Kontakten und Anschlüssen - Prüfung 16n: Biegefestigkeit
von Flachsteckern (IEC 60512-16-14:2008)
Connecteurs pour équipements électroniques - Essais et mesures - Partie 16-14: Essais
mécaniques des contacts et des sorties - Essai 16n: Résistance à la flexion des
languettes fixes (CEI 60512-16-14:2008)
Ta slovenski standard je istoveten z: EN 60512-16-14:2008
ICS:
19.060 Mehansko preskušanje Mechanical testing
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60512-16-14:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60512-16-14:2008

---------------------- Page: 2 ----------------------

SIST EN 60512-16-14:2008

EUROPEAN STANDARD
EN 60512-16-14

NORME EUROPÉENNE
September 2008
EUROPÄISCHE NORM

ICS 31.220.10


English version


Connectors for electronic equipment -
Tests and measurements -
Part 16-14: Mechanical tests on contacts and terminations -
Test 16n: Bending strength, fixed male tabs
(IEC 60512-16-14:2008)


Connecteurs  Steckverbinder
pour équipements électroniques - für elektronische Einrichtungen -
Essais et mesures - Mess- und Prüfverfahren -
Partie 16-14: Essais mécaniques Teil 16-14: Mechanische Prüfungen
des contacts et des sorties - an Kontakten und Anschlüssen -
Essai 16n: Résistance à la flexion Prüfung 16n: Biegefestigkeit von
des languettes fixes Flachsteckern
(CEI 60512-16-14:2008) (IEC 60512-16-14:2008)



This European Standard was approved by CENELEC on 2008-08-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60512-16-14:2008 E

---------------------- Page: 3 ----------------------

SIST EN 60512-16-14:2008
EN 60512-16-14:2008 - 2 -
Foreword
The text of document 48B/1889/FDIS, future edition 1 of IEC 60512-16-14, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60512-16-14 on 2008-08-01.
This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the
structure of the EN 60512 series.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2009-05-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2011-08-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60512-16-14:2008 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60512-16-14:2008
- 3 - EN 60512-16-14:2008
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced docume
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60352-9:2024(Main)
Solderless connections - Part 9: Ultrasonically welded connections - General requirements, test methods and practical guidance
SIST EN IEC 60352-9:2024

IEC 60352-9:2024 provides guidelines for welding and testing of ultrasonically welded connections and includes requirements, tests and practical guidance information. Ultrasonic welding is a form of cold friction welding that is becoming increasingly popular in many industries. This type of welding uses ultrasonic vibration to join materials together, creating a bond that is both strong and reliable. Ultrasonic welding has been identified as a process in ISO 4063-41 by the International Organization for Standardization (ISO). The process of ultrasonic welding relies on high frequency ultrasound waves being used to create frictional heat at the connection point. High temperature is not required for this special method of welding, making it one of the most cost-effective ways to join two materials together. It also requires fewer steps than traditional methods, meaning it can be completed quickly and with minimal resources. Ultrasonic welding has been around for decades but only recently has become more widely utilized due to advances in technology and its availability at lower cost. It can be used on many different materials including plastics, rubbers, metals, textiles, and composites. Due to its precision and strong bonds it creates, it has become extremely popular in manufacturing processes such as automotive industry, electronics industry, furniture production and even medical device production. This document covers ultrasonically welded connections made with stranded or flexible wires (class 2, 5 or 6 per IEC 60228) of copper or copper alloy, as well as of aluminium or aluminium alloy. These welded metal-to-metal connections shall employ wires with cross-sectional area of 0,08 mm2 to 160 mm2 and shall not exceed a total cross-sectional area, in case of wire bundle, of 200 mm2. For aluminium or aluminium alloy wires, the minimum required cross-sectional area is 2,5 mm2. Additionally, information on materials, data from industrial experience and test procedures are included to ensure electrically stable connections under prescribed environmental conditions. Lastly, this document aims to achieve comparable results when using ultrasonic welding equipment with similar performance and specifications as specified by the termination manufacturer.

  • Draft
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-3-106:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 3-106: Rectangular connectors - Detail specification for protective housings for use with 8-way shielded and unshielded connectors for industrial environments incorporating the IEC 60603-7 series interface
SIST EN IEC 61076-3-106:2023

IEC 61076-3-106:2023 constitutes a detail product specification for 8-way connectors for data transmission with frequencies up to 600 MHz. It covers protective housings for upgrading existing 8-way shielded and unshielded connectors utilizing the interface described in the IEC 60603-7 series to IP65/IP67 rating according to IEC 60529, for use in industrial environments. The housings cover a variety of different locking mechanisms according to this document and a variety of different mounting configurations and termination types which are detailed in the IEC 60603-7 series. Common mating configurations for all variants are defined in IEC 60603-7. The mating dimensions for the housings under Clause 3 allow the mating conditions under IEC 60603-7 to be fulfilled. The fully assembled variants (connectors) described in this document incorporate fully compliant IEC 60603-7 series fixed and free connectors.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-2-115:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-115: Circular connectors - Detail specification for 12-pole shielded connectors with 2 A rated current and IP65/IP67 metal housing with push-pull locking
SIST EN IEC 61076-2-115:2023

IEC 61076-2-115:2023 describes free and fixed 12P shielded circular connectors with 2 A rated current, rated voltage up to and including 50 V AC/DC, IP65/IP67 metal housing with push-pull locking (hereinafter referred to as a connectors) for use in electrical and electronic equipment. It includes overall dimensions, interface dimensions, technical characteristics, performance requirements and test methods.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-2-116:2023(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2 -116: Detail specification for circular connectors size 15 with up to 3+PE power contacts and auxiliary contacts, with bayonet-locking
SIST EN IEC 61076-2-116:2023

IEC 61076-2-116:2022 specifies circular connectors size 15 with bayonet-locking, with up to 3 power contacts with rated insulation voltage up to 630 V AC/DC and rated current up to 20 A, plus PE, and up to 3 auxiliary contacts with rated insulation voltage up to 63 V AC/DC and rated current up to 10 A, that are typically used for industrial power supply and power applications, such as the feeding and control of 3-phase asynchronous motors. These connectors consist of both fixed and free connectors either rewireable or non-rewireable, with bayonet-locking. Male connectors have round contacts, either power or signal, Ø1,6 mm.

  • Standard
    48 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 63171-5:2022(Main)
Connectors for electrical and electronic equipment - Part 5: Detail specification for 2-way M8 and M12 circular connectors, shielded or unshielded, free and fixed - Mechanical mating information, pin assignment and additional requirements for Type 5
SIST EN IEC 63171-5:2022

This part of IEC 63171 describes shielded or unshielded circular connectors with 2 ways and M8 or M12 Styles, typically used for data transmission up to 600 MHz and with current carrying capacity up to 4 A, for use in areas with harsh environmental conditions. These connectors consist of fixed and free connectors either rewirable or non-rewirable. Male connectors have square cross- section contacts, for data and power transmission. M12 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-101 of this size of circular connectors. M8 describes the dimensions of the styles and thread of the screw-locking mechanism according IEC 61076-2-104. The use of alternative locking mechanisms according to IEC 61076-2-010 or IEC 61076-2-011 are possible. The coding provided by this standard prevents the mating of accordingly coded male or female connectors to other similarly sized interfaces covered by this or other standards. These Type 5 connectors are interoperable with Type 2 connectors according IEC 63171-2, except the locking and sealing system provided by the outer shell. The shielded and unshielded connectors are interoperable for their internal transmission performance and can be exchanged. The shielded version has improved EMC and coupling properties. This part of IEC 63171 covers Type 5 connectors. Each part of this series has the associated type number equal to the number of the part in the series. All connectors in the IEC 63171 series are deemed to provide the same functions as defined in IEC 63171:2021, using different mechanical interfaces.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-27-200:2022(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 27-200: Additional specifications for signal integrity tests up to 2 000 MHz on IEC 60603-7 series connectors - Tests 27a to 27g
SIST EN IEC 60512-27-200:2022

IEC 60512-27-200:2022 is primarily intended for use in signal integrity and transmission performance testing up to 2 000 MHz of IEC 60603-7 series 8-way connector type IEC 60603‑7‑81, according to connector test method IEC 60512‑28‑100. This part of IEC 60512 covers additional, supplemental test method specifications to extend the upper frequency for the test connectors and associated indirect-reference test fixtures used in the signal integrity and transmission performance tests specified in IEC 60512‑27‑100. In support of de-embedded crosstalk and related transmission requirements specified in IEC 60603‑7‑81, for frequencies up to 2 000 MHz, these supplemental specifications extend the upper test frequency from IEC 60512‑27‑100 up to 500 MHz to the upper test frequency of IEC 60512‑28‑100 up to 2 000 MHz. This document covers measurements of connector signal integrity and transmission performance of 8-way connector types defined in these published connector series standards: - IEC 60603‑7‑2 - IEC 60603‑7‑3 - IEC 60603‑7‑4 - IEC 60603‑7‑5 - IEC 60603‑7‑41 - IEC 60603‑7‑51 - IEC 60603‑7‑81. This document covers respective performance test procedures of connector signal integrity and transmission performance defined in these published connector test method series standards: - IEC 60512‑26‑100 - IEC 60512‑27‑100 - IEC 60512‑28‑100.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60512-99-002:2022(Main)
Connectors for electrical and electronic equipment - Tests and measurements - Part 99-002: Endurance test schedules - Test 99b: Test schedule for unmating under electrical load
SIST EN IEC 60512-99-002:2022

This part of IEC 60512 is used for the assessment of connectors within the scope of SC 48B that are used in twisted pair communication cabling with remote power, such as ISO/IEC 11801-1 Class D, or better, balanced cabling in support of IEEE 802.3btTM (Power over Ethernet, supporting up to 90 W from the power sourcing equipment). The object of this document is to detail a test schedule to determine the ability of sets of connectors to withstand a minimum of 100 mechanical operations with electrical load, where an electrical current is being passed through the connectors in accordance with IEC 60512-9-3 during the separation (unmating) step.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-2-011:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-011: Circular connectors - Detail specification for B12 bayonet coupling connectors based on mating interfaces according to IEC 61076-2-101 and IEC 61076-2-109
SIST EN IEC 61076-2-011:2021

IEC 61076-2-011:2021 describes the bayonet coupling interface of circular connectors that are typically used for industrial process measurement and control. These connectors consist of fixed and free connectors either rewireable or non-rewireable, with bayonet-coupling. These connectors may have glass to metal seal inserts. They have male or female contacts and are deemed to be intermateable with corresponding free connectors produced according to this document. Male connectors have round contacts Ø 0,6 mm, Ø 0,76 mm, Ø 0,8 mm and Ø 1,0 mm. Different codings prevent the mating of these individually coded fixed connectors (and consequently of individually coded free connectors deemed to couple with them) to other interfaces and cross-mating between the different codings. However, the styles and interface dimensions, except for the coupling mechanism, are as given in 4.3 of IEC 61076-2- 101:2012 and 4.3.1 of IEC 61076-2-109:2014. The male type B12 circular connectors are interoperable with the female type B12 connector of the same coding and ways. The female type B12 connectors are interoperable with the male type B12 and M12 (threaded screw coupling) connector of the same coding and ways.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-2-010:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 2-010: Circular connectors - Detail specification for connectors with outer or inner push-pull locking mechanism, based on mating interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 and IEC 61076-2-113
SIST EN IEC 61076-2-010:2021

IEC 61076-2-010:2021 specifies circular connectors with a push-pull locking mechanism of a size derived from, and thus being compatible with M12 screw-locking connectors (free connectors with screw-locking according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 or IEC 61076-2-113 are compatible with push‑pull fixed interfaces according to this document) and with mating interfaces according to IEC 61076-2-101, IEC 61076-2-109, IEC 61076-2-111 (except codings E in general and coding F for inner push-pull) or IEC 61076-2-113. A fixed connector with push-pull locking according to this document is intermateable with a correspondingly coded free connector with M12 screw-locking according to any of the above mentioned standards. M12 is the dimension of the thread of the screw-locking mechanism of circular connectors with M12 screw-locking. IEC 61076-2-012 defines another inner push-pull for fixed female connectors which is however not compatible to the inner push-pull defined in this document. Annex C shows the different styles of female free connectors to extend male free connectors. This document covers both: a) power connectors with current ratings up to 16 A and voltage ratings up to 630 V, typically used for power supply and power applications in industrial premises, and b) connectors for data and signal transmission with frequencies up to 500 MHz. These connectors consist of both, fixed and free connectors, either rewirable or non-rewirable, with M12 push-pull locking as explained above. Male connectors have round contacts from Ø 0,6 mm up to Ø 1,5 mm. In addition, the push-pull mechanisms consist of 2 different push-pull designs: c) An outer push-pull for male and female fixed connector, where the locking groove is placed onto the outer cylindric surface of the housing. The outer push-pull for female fixed connectors is made for 2 different types of male connectors. It has locking means for both types on its outer surface. For design and dimensions see 5.3.2 and 5.3.3. d) An inner push-pull for female fixed connectors and for male free connectors, where the locking means are placed onto the inner cylindric surface of the housing. For design and dimensions see 5.3.4. The different codings provided by IEC 61076-2 series detail specifications mentioned within this document prevent the mating of accordingly coded male or female connectors to any other similarly sized interfaces, covered by other standards and the cross-mating between the different codings provided by any other IEC 61076-2 series detail specification mentioned within this document.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61076-3-122:2021(Main)
Connectors for electrical and electronic equipment - Product requirements - Part 3-122: Detail specification for 8-way, shielded, free and fixed connectors for I/O and data transmission with frequencies up to 500 MHz and current-carrying capacity in industrial environments
SIST EN IEC 61076-3-122:2021

IEC 61076-3-122:2021 covers 8-way, shielded, free and fixed rectangular connectors for I/O and data transmission with frequencies up to 500 MHz. It is intended to specify the common dimensions, mechanical, electrical and environmental characteristics and tests for this family of connectors. Connectors complying with this document provide an ingress protection level of IP20; however, they are particularly suited for industrial environments with a high level of vibration. There are two classes of connectors defined in this document, indicated by "class A" and "class B" which are distinguished by some electrical and mechanical characteristics to meet the particular sets of requirements of some industrial applications. Class A meets the requirements defined in Ed.1 of this document. With the two classes A and B, the two codings Type I and II, and the two sets of transmission requirements according to the component categories Cat 5 and Cat 6A as defined in ISO/IEC 11801-1, this document specifies 2 × 2 × 2 = 8 variants. All connectors covered by this document feature a current-carrying capacity beyond the minimum requirement of 0,75 A per pin for an ambient temperature of 60° C as defined in ISO/IEC 11801 1. This second edition cancels and replaces the first edition published in 2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Title modified. b) Introduction of two sets of requirements for connectors of "class A" and "class B" where class A matches the requirements defined in the previous edition. c) Definition of new performance requirements for frequencies up to 500 MHz in addition to the performance requirements up to 100 MHz provided with the previous edition. d) Re-structuring to reflect the commonalities of and differences between connector Type I and Type II. e) Revision of drawings to clarify some dimensions. e) The derating diagram has been corrected to align it with the upper limiting temperature in the climatic category, with no reduction of performance for the target applications.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day