EN 60745-2-20:2003
(Main)Hand-held motor-operated electric tools - Safety - Part 2-20: Particular requirements for band saws
Hand-held motor-operated electric tools - Safety - Part 2-20: Particular requirements for band saws
Deals with the safety of hand held motor operated electric tools, particular requirements for band saws. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three phase a.c. tools.
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-20: Besondere Anforderungen für Bandsägen
Outils électroportatifs à moteur - Sécurité - Partie 2-20: Règles particulières pour les scies à ruban
Deals with the safety of hand held motor operated electric tools, particular requirements for band saws. The rated voltage being not more than 250 V for single-phase a.c. or d.c., and 440 V for three phase a.c. tools.
Ročna električna orodja - Varnost - 2-20. del: Posebne zahteve za tračne žage (IEC 60745-2-20:2003; spremenjen)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60745-2-20:2004
01-marec-2004
5RþQDHOHNWULþQDRURGMD9DUQRVWGHO 3RVHEQH]DKWHYH]DWUDþQHåDJH ,(&
VSUHPHQMHQ
Hand-held motor-operated electric tools - Safety -- Part 2-20: Particular requirements for
band saws
Handgeführte motorbetriebene Elektrowerkzeuge - Sicherheit -- Teil 2-20: Besondere
Anforderungen für Bandsägen
Outils électroportatifs à moteur - Sécurité -- Partie 2-20: Règles particulières pour les
scies à ruban
Ta slovenski standard je istoveten z: EN 60745-2-20:2003
ICS:
25.080.60 Strojne žage Sawing machines
25.140.20 (OHNWULþQDRURGMD Electric tools
SIST EN 60745-2-20:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
NORME CEI
INTERNATIONALE IEC
60745-2-20
INTERNATIONAL
Première édition
STANDARD
First edition
2003-02
Outils électroportatifs à moteur –
Sécurité –
Partie 2-20:
Règles particulières pour les scies à ruban
Hand-held motor-operated electric tools –
Safety –
Part 2-20:
Particular requirements for band saws
IEC 2003 Droits de reproduction réservés Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
G
Commission Electrotechnique Internationale PRICE CODE
International Electrotechnical Commission
Международная Электротехническая Комиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 2 ----------------------
60745-2-20 IEC:2003 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS –
SAFETY –
Part 2-20: Particular requirements for band saws
FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International
Organization for Standardization (ISO) in accordance with conditions determined by agreement between the
two organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical specifications, technical reports or guides and they are accepted by the National
Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.
This part of International Standard IEC 60745 has been prepared by subcommittee 61F:
Safety of hand-held, motor-operated electric tools, of IEC technical committee 61:Safety of
household and similar electrical appliances
This bilingual version (2003-03) replaces the English version.
The text of this standard is based on the following documents:
FDIS Report on voting
61F/508/FDIS 61F/519/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.