SIST EN 60317-0-1:2014
(Main)Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire
EN-IEC 60317 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-1: Allgemeine Anforderungen - Runddrähte aus Kupfer, lackisoliert
Spécifications pour types particuliers de fils de bobinage - Parte 0-1: Prescriptions générales - Fil de section circulaire en cuivre émaillé
La CEI 60317-0-1:2013 spécifie les exigences générales pour les fils de bobinage de section circulaire en cuivre émaillé avec ou sans couche adhérente. La gamme des diamètres nominaux des conducteurs est donnée dans la feuille de spécification appropriée. Cette quatrième édition annule et remplace la troisième édition parue en 2008. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - la révision de la définition de la dimension nominale du conducteur; - un nouveau paragraphe contenant des notes générales sur le fil de bobinage intégrées auparavant au domaine d'application; - révision des exigences d'allongement dans le Tableau 4; - révision de l'Article 13, Tension de claquage, pour inclure de nouvelles exigences pour les diamètres de fils intermédiaires; - révision des exigences de continuité de l'isolant dans le Tableau 13; - révision de l'introduction de l'Annexe A; - révision du B.2 de l'Annexe B; - révision du Tableau C.1 de l'Annexe C. Mots clés: exigences pour les fils de bobinage de section circulaire en cuivre émaillé
Specifikacije za posebne vrste navijalnih žic - 0-1. del: Splošne zahteve - Prevlečena okrogla bakrena žica
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Spécifications pour types particuliers de fils de bobinage - Parte 0-1: Prescriptions générales - Fil de section circulaire en cuivre émailléSpecifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire77.150.30Bakreni izdelkiCopper products29.060.10ŽiceWiresICS:Ta slovenski standard je istoveten z:EN 60317-0-1:2014SIST EN 60317-0-1:2014en01-marec-2014SIST EN 60317-0-1:2014SLOVENSKI
STANDARDSIST EN 60317-0-1:20081DGRPHãþD
SIST EN 60317-0-1:2014
EUROPEAN STANDARD EN 60317-0-1 NORME EUROPÉENNE
EUROPÄISCHE NORM January 2014
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2014 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-1:2014 E
ICS 29.060.10 Supersedes EN 60317-0-1:2008
English version
Specifications for particular types of winding wires -
Part 0-1: General requirements -
Enamelled round copper wire (IEC 60317-0-1:2013)
Spécifications pour types particuliers de fils de bobinage -
Partie 0-1: Exigences générales -
Fil de section circulaire en cuivre émaillé (CEI 60317-0-1:2013)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten -
Teil 0-1: Allgemeine Anforderungen -
Runddrähte aus Kupfer, lackisoliert (IEC 60317-0-1:2013)
This European Standard was approved by CENELEC on 2013-11-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 60317-0-1:2014
EN 60317-0-1:2014 - 2 - Foreword The text of document 55/1409/FDIS, future edition 4 of IEC 60317-0-1, prepared by IEC/TC 55 "Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-1:2014.
The following dates are fixed: • latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-08-11 • latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-11-11
This document supersedes EN 60317-0-1:2008.
EN 60317-0-1:2014 includes the following significant technical changes with respect to EN 60317-0-1:2008: – revision to the definition of nominal conductor dimension; – new subclause containing general notes on winding wire, formerly a part of the scope; – revision to elongation requirements in Table 4; – revisions to Clause 13, Breakdown voltage, to include new requirements for intermediate wire diameters; – revision to continuity of insulation requirements in Table 13; – revision to the introduction of Annex A; – revision to B.2 of Annex B; – revision to Table C.1 of Annex C.
This standard is to be read in conjunction with the EN 60851 series. The clause numbers used in this part of EN 60317 are identical with the respective test numbers of the EN 60851 series.
In case of inconsistencies between EN 60851 and this part of EN 60317, the latter prevails.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.
Endorsement notice The text of the International Standard IEC 60317-0-1:2013 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60264 Series NOTE Harmonized as EN 60264 Series (not modified). IEC 60317 Series NOTE Harmonized as EN 60317 Series (not modified).
SIST EN 60317-0-1:2014
- 3 - EN 60317-0-1:2014 Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60172 - Test procedure for the determination of the temperature index of enamelled winding wires EN 60172 -
IEC 60851 Series Winding wires - Test methods EN 60851 Series
ISO 3 - Preferred numbers - Series of preferred numbers - -
SIST EN 60317-0-1:2014
SIST EN 60317-0-1:2014
IEC 60317-0-1 Edition 4.0 2013-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires –
Part 0-1: General requirements – Enamelled round copper wire
Spécifications pour types particuliers de fils de bobinage –
Partie 0-1: Exigences générales – Fil de section circulaire en cuivre émaillé
INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE V ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1150-2
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale ®
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé. SIST EN 60317-0-1:2014
– 2 – 60317-0-1 © IEC:2013
CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions, general notes and appearance . 7 3.1 Terms and definitions . 7 3.2 General notes . 8 3.2.1 Methods of test . 8 3.2.2 Winding wire . 9 3.3 Appearance . 9 4 Dimensions . 9 4.1 Conductor diameter . 9 4.2 Out of roundness of conductor (nominal conductor diameters over 0,063 mm). 13 4.3 Minimum increase in diameter due to the insulation and the bonding layer (nominal conductor diameters over 0,063 mm) . 13 4.3.1 Enamelled wires without a bonding layer . 13 4.3.2 Enamelled wires with a bonding layer . 13 4.3.3 Intermediate nominal conductor diameters . 13 4.4 Maximum overall diameter . 13 4.4.1 Enamelled wires without a bonding layer . 13 4.4.2 Enamelled wires with a bonding layer . 14 5 Electrical resistance . 14 6 Elongation . 15 7 Springiness . 15 7.1 Nominal conductor diameters from 0,080 mm up to and including 1,600 mm . 15 7.2 Nominal conductor diameters over 1,600 mm . 15 8 Flexibility and adherence . 17 8.1 Mandrel winding test (nominal conductor diameters up to and including 1,600 mm) . 17 8.2 Stretching test (nominal conductor diameters over 1,600 mm) . 17 8.3 Jerk test (nominal conductor diameters up to and including 1,000 mm) . 17 8.4 Peel test (nominal conductor diameters over 1,000 mm) . 17 9 Heat shock . 18 9.1 Nominal conductor diameters up to and including 1,600 mm. 18 9.2 Nominal conductor diameters over 1,600 mm . 18 10 Cut-through . 19 11 Resistance to abrasion . 19 12 Resistance to solvents . 19 13 Breakdown voltage . 19 13.1 General . 19 13.2 Nominal conductor diameters up to and including 0,100 mm. 19 13.3 Nominal conductor diameters over 0,100 mm up to and including 2,500 mm . 21 13.4 Nominal conductor diameters over 2,500 mm . 23 14 Continuity of insulation (nominal conductor diameters up to and including 1,600 mm) . 24 15 Temperature index . 24 SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 3 –
16 Resistance to refrigerants . 24 17 Solderability . 24 18 Heat or solvent bonding . 24 19 Dielectric dissipation factor . 24 20 Resistance to transformer oil . 24 21 Loss of mass . 24 23 Pin hole test . 25 30 Packaging. 25 Annex A (informative)
Dimensions for intermediate nominal conductor diameters (R 40) . 26 Annex B (informative)
Method for the calculation of linear resistance . 30 Annex C (informative)
Resistance. 32 Bibliography . 34
Table 1 – Dimensions of enamelled wires (R 20) – Preferred nominal conductor diameters (1 of 2) . 10 Table 2 – Dimensions of enamelled wires with a bonding layer (R 20) –
Preferred nominal conductor diameters (1 of 2) . 12 Table 3 – Electrical resistance . 14 Table 4 – Elongation . 15 Table 5 – Springiness . 16 Table 6 – Mandrel winding . 17 Table 7 – Heat shock . 18 Table 8 – Breakdown voltage – Preferred nominal conductor diameters (R 20) (0,018 mm up to and including 0,100 mm) . 20 Table 9 – Breakdown voltage – Intermediate nominal conductor diameters (R 40) (0,019 mm up to and including 0,095 mm) . 21 Table 10 – Breakdown voltage – Preferred nominal conductor diameters (R 20) (0,112 mm up to and including 2,500 mm) . 22 Table 11 – Breakdown voltage – Intermediate nominal conductor diameters (R 40) (0,106 mm up to and including 0,950 mm) . 23 Table 12 – Breakdown voltage – Nominal conductor diameters over 2,500 mm . 23 Table 13 – Continuity of insulation . 24 Table 14 – Maximum number of pin holes . 25 Table A.1 – Dimensions of enamelled wires (R 40) – Intermediate nominal conductor diameters (1 of 2) . 26 Table A.2 – Dimensions of enamelled wires with a bonding layer (R 40) – Intermediate nominal conductor diameters (1 of 2) . 28 Table B.1 – Ratios. 31 Table C.1 – Electrical resistances – Nominal conductor diameters
over 0,063 mm up to and including 1,000 mm (1 of 2) . 32
SIST EN 60317-0-1:2014
– 4 – 60317-0-1 © IEC:2013
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 0-1: General requirements –
Enamelled round copper wire
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-0-1 has been prepared by IEC technical committee 55: Winding wires.
This fourth edition cancels and replaces the third edition published in 2008. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: – revision to the definition of nominal conductor dimension; – new subclause containing general notes on winding wire, formerly a part of the scope; – revision to elongation requirements in Table 4; – revisions to Clause 13, Breakdown voltage, to include new requirements for intermediate wire diameters; SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 5 –
– revision to continuity of insulation requirements in Table 13; – revision to the introduction of Annex A; – revision to B.2 of Annex B; – revision to Table C.1 of Annex C. This standard is to be read in conjunction with the IEC 60851 series. The clause numbers used in this part of IEC 60317 are identical with the respective test numbers of the IEC 60851 series. In case of inconsistencies between IEC 60851 and this part of IEC 60317, the latter prevails. The text of this standard is based on the following documents: FDIS Report on voting 55/1409/FDIS 55/1430/RVD
Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended.
SIST EN 60317-0-1:2014
– 6 – 60317-0-1 © IEC:2013
INTRODUCTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires – Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wires (IEC 60264).
SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 7 –
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 0-1: General requirements –
Enamelled round copper wire
1 Scope This part of IEC 60317 specifies general requirements of enamelled round copper winding wires with or without bonding layer. The range of nominal conductor diameters is given in the relevant specification sheet.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60172, Test procedure for the determination of the temperature index of enamelled winding wires IEC 60851 (all parts), Winding wires – Test methods
ISO 3, Preferred numbers – Series of preferred numbers 3 Terms, definitions, general notes and appearance For the purposes of this document, the following terms and definitions apply. 3.1 Terms and definitions
3.1.1
bonding layer material which is deposited on an enamelled wire and which has the specific function of bonding wires together 3.1.2
class thermal performance of a wire expressed by the temperature index and the heat shock temperature 3.1.3
coating material which is deposited on a conductor or wire by a suitable means and then dried and/or cured 3.1.4
conductor bare metal after removal of the insulation SIST EN 60317-0-1:2014
– 8 – 60317-0-1 © IEC:2013
3.1.5
crack opening in the insulation which exposes the conductor to view at the stated magnification 3.1.6
dual coating insulation composed of two different materials, an underlying and a superimposed coating 3.1.7
enamelled wire wire coated with an insulation of cured resin 3.1.8
grade range of thickness of the insulation of a wire 3.1.9
insulation coating or covering on the conductor with the specific function of withstanding voltage 3.1.10
nominal conductor dimension designation of the conductor size in accordance with the IEC 60317 series
3.1.11
normal vision 20/20 vision, with corrective lenses, if necessary 3.1.12
sole coating insulation composed of one material 3.1.13
winding wire wire used for winding a coil to provide a magnetic field 3.1.14
wire conductor coated or covered with an insulation 3.2 General notes 3.2.1 Methods of test All methods of test to be used for this part of IEC 60317 are given in the IEC 60851 series.
The clause numbers used in this standard are identical to the corresponding test numbers in the IEC 60851 series of standards. In case of inconsistencies between the publication on methods of test and this standard, IEC 60317-0-1 shall prevail.
Where no specific range of nominal conductor diameters is given for a test, the test applies to all nominal conductor diameters covered by the specification sheet.
Unless otherwise specified, all tests shall be carried out at a temperature from 15 °C to 35 °C and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 9 –
shall be preconditioned under these atmospheric conditions for a time sufficient to allow the specimens to reach stability.
The wire to be tested shall be removed from the packaging in such a way that the wire will not be subjected to tension or unnecessary bends. Before each test, sufficient wire should be discarded to ensure that any damaged wire is not included in the test specimens. 3.2.2 Winding wire See the relevant specification sheet. In addition, when reference is made to a winding wire according to a standard of the IEC 60317 series mentioned under Clause 2, the following information is given in the description: – reference to IEC specification; – nominal conductor diameter in millimetres; – grade. EXAMPLE IEC 60317-1 – 0,500 Grade 2 3.3 Appearance The film coating shall be essentially smooth and continuous, free from streaks, blisters and foreign material when examined with normal vision, as wound on the original spool or reel. When agreed upon between the user and supplier, examination using 6× to 10× magnification shall be used for wires with a nominal diameter less than 0,1 mm. 4 Dimensions
4.1 Conductor diameter
The series of preferred nominal conductor diameters shall correspond to series R 20 according to ISO 3. The actual values and their tolerances are given in Tables 1 and 2.
The series of intermediate diameters from which the user may select intermediate nominal conductor diameters, when required for technical reasons, shall correspond to series R 40 according to ISO 3. The actual values and their tolerances are given in Annex A. The conductor diameter shall not differ from the nominal diameter by more than the limit given in Tables 1 or 2.
SIST EN 60317-0-1:2014
– 10 – 60317-0-1 © IEC:2013
Table 1 – Dimensions of enamelled wires (R 20) – Preferred nominal conductor diameters (1 of 2) Nominal conductor diameter Conductor tolerance ± Minimum increase due to the insulation mm Maximum overall diameter mm mm mm Grade 1 Grade 2 Grade 3 Grade 1 Grade 2 Grade 3 0,018 0,020 0,022 0,025 0,028
0,002 0,002 0,002 0,003 0,003 0,004 0,004 0,005 0,005 0,006 0,006 0,007 0,008 0,008 0,009 0,022 0,024 0,027 0,031 0,034 0,024 0,027 0,030 0,034 0,038 0,026 0,030 0,033 0,037 0,042 0,032 0,036 0,040 0,045 0,050
0,003 0,004 0,004 0,005 0,005 0,007 0,008 0,008 0,009 0,010 0,010 0,011 0,012 0,013 0,014
0,039 0,044 0,049 0,055 0,060 0,043 0,049 0,054 0,061 0,066 0,047 0,053 0,058 0,066 0,072 0,056 0,063 0,071 0,080 0,090
0,003 0,003 0,003 0,006 0,006 0,007 0,007 0,008 0,011 0,012 0,012 0,014 0,015 0,015 0,017 0,018 0,020 0,022 0,067 0,076 0,084 0,094 0,105 0,074 0,083 0,091 0,101 0,113 0,081 0,090 0,098 0,108 0,120 0,100 0,112 0,125 0,140 0,160
0,003 0,003 0,003 0,003 0,003 0,008 0,009 0,010 0,011 0,012 0,016 0,017 0,019 0,021 0,023 0,023 0,026 0,028 0,030 0,033 0,117 0,130 0,144 0,160 0,182 0,125 0,139 0,154 0,171 0,194 0,132 0,147 0,163 0,181 0,205 0,180 0,200 0,224 0,250 0,280
0,003 0,003 0,003 0,004 0,004 0,013 0,014 0,015 0,017 0,018 0,025 0,027 0,029 0,032 0,033 0,036 0,039 0,043 0,048 0,050 0,204 0,226 0,252 0,281 0,312 0,217 0,239 0,266 0,297 0,329 0,229 0,252 0,280 0,312 0,345 0,315 0,355 0,400 0,450 0,500
0,004 0,004 0,005 0,005 0,005 0,019 0,020 0,021 0,022 0,024 0,035 0,038 0,040 0,042 0,045 0,053 0,057 0,060 0,064 0,067 0,349 0,392 0,439 0,491 0,544 0,367 0,411 0,459 0,513 0,566 0,384 0,428 0,478 0,533 0,587
SIST EN 60317-0-1:2014
60317-0-1 © IEC:2013 – 11 –
Table 1 (2 of 2) Nominal conductor diameter Conductor tolerance ± Minimum increase due to the insulation mm Maximum overall diameter mm mm mm Grade 1 Grade 2 Grade 3 Grade 1 Grade 2 Grade 3 0,560 0,630 0,710 0,800 0,900
0,006 0,006 0,007 0,008 0,009 0,025 0,027 0,028 0,030 0,032 0,047 0,050 0,053 0,056 0,060 0,071 0,075 0,080 0,085 0,090 0,606 0,679 0,762 0,855 0,959 0,630 0,704 0,789 0,884 0,989 0,653 0,728 0,814 0,911 1,018 1,000 1,120 1,250 1,400 1,600 0,010 0,011 0,013 0,014 0,016 0,034 0,034 0,035 0,036 0,038 0,063 0,065 0,067 0,069 0,071 0,095 0,098 0,100 0,103 0,107 1,062 1,184 1,316 1,468 1,670 1,094 1,217 1,349 1,502 1,706 1,124 1,248 1,381 1,535 1,740
1,800 2,000 2,240 2,500 2,800
0,018 0,020 0,022 0,025 0,028 0,039 0,040 0,041 0,042 0,043 0,073 0,075 0,077 0,079 0,081 0,110 0,113 0,116 0,119 0,123 1,872 2,074 2,316 2,578 2,880 1,909 2,112 2,355 2,618 2,922 1,944 2,148 2,392 2,656 2,961 3,150 3,550 4,000 4,500 5,000
0,032 0,036 0,040 0,045 0,050 0,045 0,046 0,047 0,049 0,050 0,084 0,086 0,089 0,092 0,094 0,127 0,130 0,134 0,138 0,142 3,233 3,635 4,088 4,591 5,093 3,276 3,679 4,133 4,637 5,141 3,316 3,721 4,176 4,681 5,186 NOTE Minimum overall diameter up to and in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.