EN IEC 60317-0-4:2020
(Main)Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
Specifications for particular types of winding wires - Part 0-4: General requirements - Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire
IEC 60317-0-4:2020 is available as IEC 60317-0-4:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60317-0-4:2020 specifies general requirements of glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper wire.The range of nominal conductor dimensions is given in 4.1 and the relevant specification sheet. This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - addition of dimensional requirements for grade 1 enamelled wire in Table 4; - addition of dielectric breakdown requirements for grade 1 enamelled wire in Table 7. - addition of requirement for the adherence test in 8.2.1 and 8.2.2.
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-4: Allgemeine Anforderungen - Flachdrähte aus Kupfer, umsponnen mit Glas-Fasergewebe, blank oder lackisoliert, imprägniert mit Harz oder Lack
Spécifications pour types particuliers de fils de bobinage - Partie 0-4: Exigences générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre imprégnées de vernis ou de résine
IEC 60317-0-4:2020 est disponible sous forme de IEC 60317-0-4:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.IEC 60317-0-4:2020 spécifie les exigences générales relatives aux fils de section rectangulaire en cuivre nus ou émaillés, guipés de fibres de verre imprégnées de vernis ou de résine. La gamme des dimensions nominales des conducteurs est indiquée en 4.1 et dans la feuille de spécifications correspondante. Cette quatrième édition annule et remplace la troisième édition parue en 2015. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: - ajout des exigences dimensionnelles pour le fil émaillé de grade 1 dans le Tableau 4; - ajout des exigences de claquage diélectrique pour le fil émaillé de grade 1 dans le Tableau 7; - ajout des exigences pour l'essai d'adhérence en 8.2.1 et en 8.2.2.
Specifikacije za posebne vrste navijalnih žic - 0-4. del: Splošne zahteve - Bakrena žica s pravokotnim prerezom, gola ali emajlirana, ovita z optičnimi vlakni in impregnirana s smolo ali lakom (IEC 60317-0-4:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 60317-0-4:2020
01-oktober-2020
Nadomešča:
SIST EN 60317-0-4:2016
Specifikacije za posebne vrste navijalnih žic - 0-4. del: Splošne zahteve - Bakrena
žica s pravokotnim prerezom, gola ali emajlirana, ovita z optičnimi vlakni in
impregnirana s smolo ali lakom (IEC 60317-0-4:2020)
Specifications for particular types of winding wires - Part 0-4: General requirements -
Glass-fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper
wire (IEC 60317-0-4:2020)
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-4:
Allgemeine Anforderungen - Flachdrähte aus Kupfer, blank oder lackisoliert und umhüllt
mit Glasgewebe, imprägniert mit Harz oder Lack (IEC 60317-0-4:2020)
Spécifications pour types particuliers de fils de bobinage - Partie 0-4: Exigences
générales - Fil de section rectangulaire en cuivre nu ou émaillé, guipé de fibres de verre
imprégnées de vernis ou de résine (IEC 60317-0-4:2020)
Ta slovenski standard je istoveten z: EN IEC 60317-0-4:2020
ICS:
29.060.10 Žice Wires
77.150.30 Bakreni izdelki Copper products
SIST EN IEC 60317-0-4:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 60317-0-4:2020
---------------------- Page: 2 ----------------------
SIST EN IEC 60317-0-4:2020
EUROPEAN STANDARD EN IEC 60317-0-4
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2020
ICS 29.060.10 Supersedes EN 60317-0-4:2016 and all of its
amendments and corrigenda (if any)
English Version
Specifications for particular types of winding wires - Part 0-4:
General requirements - Glass-fibre wound, resin or varnish
impregnated, bare or enamelled rectangular copper wire
(IEC 60317-0-4:2020)
Spécifications pour types particuliers de fils de bobinage - Technische Lieferbedingungen für bestimmte Typen von
Partie 0-4: Exigences générales - Fil de section Wickeldrähten - Teil 0-4: Allgemeine Anforderungen -
rectangulaire en cuivre nu ou émaillé, guipé de fibres de Flachdrähte aus Kupfer, umsponnen mit Glasgewebe, blank
verre imprégnées de vernis ou de résine oder lackisoliert, imprägniert mit Harz oder Lack
(IEC 60317-0-4:2020) (IEC 60317-0-4:2020)
This European Standard was approved by CENELEC on 2020-06-01. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 60317-0-4:2020 E
---------------------- Page: 3 ----------------------
SIST EN IEC 60317-0-4:2020
EN IEC 60317-0-4:2020 (E)
European foreword
The text of document 55/1835A/FDIS, future edition 4 of IEC 60317-0-4, prepared by IEC/TC 55
"Winding wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN IEC 60317-0-4:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-03-01
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-06-01
document have to be withdrawn
This document supersedes EN 60317-0-4:2016 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 60317-0-4:2020 was approved by CENELEC as a
European Standard without any modification.
In the official version, fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.