EN 50632-2-11:2016/A1:2021

Electric motor-operated tools - Dust measurement procedure - Part 2-11: Particular requirements for jig and sabre saws

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for jig and sabre saws.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-11: Besondere Anforderungen für Stich- und Säbelsägen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-11: Exigences particulières pour les scies sauteuses et les scies sabres

Elektromotorna orodja - Postopek meritve prahu - 2-11. del: Posebne zahteve za vbodne in sabljaste žage - Dopolnilo A1

Ta evropski standard se uporablja za ročna elektromotorna orodja ter obravnava postopek merjenja za vbodne in sabljaste žage za izvajanje meritev emisije prahu.

General Information

• Status: Published
• Publication Date: 23-Dec-2021
• ICS: 13.040.40 - Stationary source emissions
• ICS: 25.140.20 - Electric tools
• Technical Committee: CLC/TC 116 - Safety of hand-held motor-operated electric tools
• Drafting Committee: CLC/TC 116/WG 04 - Dust
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 24-Dec-2021
• Due Date: 09-Aug-2022
• Completion Date: 24-Dec-2021
• Ref Project: SIST EN 50632-2-11:2016/A1:2022 - Electric motor-operated tools - Dust measurement procedure - Part 2-11: Particular requirements for jig and sabre saws

Relations

• Amends: EN 50632-2-11:2016 - Electric motor-operated tools - Dust measurement procedure - Part 2-11: Particular requirements for jig and sabre saws
• Effective Date: 08-Sep-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2022
Elektromotorna orodja - Postopek meritve prahu - 2-11. del: Posebne zahteve za
vbodne in sabljaste žage - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-11: Particular
requirements for jig and sabre saws
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-11: Besondere
Anforderungen für Stich- und Säbelsägen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-11:
Exigences particulières pour les scies sauteuses et les scies sabres
Ta slovenski standard je istoveten z: EN 50632-2-11:2016/A1:2021
ICS:
25.100.40 Žagni listi Saws
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-2-11:2016/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2021
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-11: Particular requirements for jig and sabre saws
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-11: Exigences particulières pour les Teil 2-11: Besondere Anforderungen für Stich- und
scies sauteuses et les scies sabres Säbelsägen
This amendment A1 modifies the European Standard EN 50632-2-11:2016; it was approved by CENELEC on 2021-12-07. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-11:2016/A1:2021 E

Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modifications to 4.3, “Operating conditions” . 4
3 Addition of Figures 101, 102 and 103 . 6
European foreword
This document (EN 50632-2-11:2016/A1:2021) has been prepared by CLC/TC 116 “Safety and environmental
aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-12-07
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-12-07
conflicting with this document have to be
withdrawn
This amendment was developed to include improvements and clarifications suggested by practical tests.
Attention is drawn to the possibility that some of the el
...