EN 50632-2-5:2016/A1:2021
(Amendment)Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular saws
Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular requirements for circular saws
This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected. This part of EN 50632 sets particular requirements for circular saws.
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-5: Besondere Anforderungen für Kreissägen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-5: Exigences particulières pour les scies circulaires
No scope available
Elektromotorna orodja - Postopek meritve prahu - 2-5. del: Posebne zahteve za krožne žage - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 50632-2-5:2016/A1:2021
01-november-2021
Elektromotorna orodja - Postopek meritve prahu - 2-5. del: Posebne zahteve za
krožne žage - Dopolnilo A1
Electric motor-operated tools - Dust measurement procedure - Part 2-5: Particular
requirements for circular saws
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 2-5: Besondere
Anforderungen für Kreissägen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 2-5:
Exigences particulières pour les scies circulaires
Ta slovenski standard je istoveten z: EN 50632-2-5:2016/A1:2021
ICS:
25.100.40 Žagni listi Saws
25.140.20 Električna orodja Electric tools
SIST EN 50632-2-5:2016/A1:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 50632-2-5:2016/A1:2021
---------------------- Page: 2 ----------------------
SIST EN 50632-2-5:2016/A1:2021
EUROPEAN STANDARD EN 50632-2-5:2016/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2021
ICS 13.040.40; 25.140.20
English Version
Electric motor-operated tools - Dust measurement procedure -
Part 2-5: Particular requirements for circular saws
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 2-5: Exigences particulières pour les Teil 2-5: Besondere Anforderungen für Kreissägen
scies circulaires
This amendment A1 modifies the European Standard EN 50632-2-5:2016; it was approved by CENELEC on 2021-08-09. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-2-5:2016/A1:2021 E
---------------------- Page: 3 ----------------------
SIST EN 50632-2-5:2016/A1:2021
EN 50632-2-5:2016/A1:2021 (E)
Contents Page
European foreword . 3
1 Modification to the European foreword . 4
2 Modification to 4.3, “Operating conditions” . 4
3 Addition of Figure 101 . 5
2
---------------------- Page: 4 ----------------------
SIST EN 50632-2-5:2016/A1:2021
EN 50632-2-5:2016/A1:2021 (E)
European foreword
This document (EN 50632-2-5:2016/A1:2021) has been prepared by CLC/TC 116 “Safety and environmental
aspects of motor-operated electric tools”.
The following dates are fixed:
• latest date by which this document has to be (dop) 2022-08-09
implemented at national level by publication of
an identical national standard or by
endorsement
• latest date by which the national standards (dow) 2024-08-09
conflicting with this document have to be
withdrawn
This amendment was developed to include improvements and clarifications suggested by practical tests.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A complete
listing of these bodies can be found on the CENELEC website.
3
---------------------- Page: 5 ----------------------
SIST EN 50632-2-5:2016/A1:2021
EN 50632-2-5:2016/A1:2021 (E)
1 Modification to th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.