iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60265-1:1998

(Main)

High-voltage switches - Part 1: Switches for rated voltages above 1 kV and less than 52 kV

High-voltage switches - Part 1: Switches for rated voltages above 1 kV and less than 52 kV

Is applicable to three-phase, alternating current switches and switch-disconnectors having making and breaking current ratings, for indoor and outdoor installations, for rated voltages above 1 kV and less than 52 kV and for rated frequencies from 16 2/3 Hz up to and including 60 Hz. This standard is also applicable to the operating devices of these switches and to their auxiliary equipment.

Hochspannungs-Lastschalter - Teil 1: Hochspannungs-Lastschalter für Nennspannungen über 1 kV und unter 52 kV

Interrupteurs à haute tension - Partie 1: Interrupteurs pour tensions assignées supérieures à 1 kV et inférieures à 52 kV

Est applicable aux interrupteurs et interrupteurs-sectionneurs à courant alternatif triphasé ayant des pouvoirs de coupure et de fermeture assignés, prévus pour l'installation à l'intérieur ou à l'extérieur, de tension assignée supérieure à 1 kV et inférieure à 52 kV et de fréquences assignées allant de 16 2/3 Hz jusqu'à et y compris 60 Hz. Cette norme est également applicable aux dispositifs de manoeuvre de ces interrupteurs et à leurs équipements auxiliaires.

High-voltage switches - Part 1: Switches for rated voltages above 1 kV and less than 52 kV

General Information

Status
Withdrawn
Publication Date
01-Apr-1998
Withdrawal Date
31-Dec-2000
ICS
29.120.40 - Switches
Technical Committee
CLC/TC 17AC - High-voltage switchgear and controlgear
Drafting Committee
IEC/SC 17A - IEC_SC_17A
Parallel Committee
IEC/SC 17A - IEC_SC_17A
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
21-Jul-2014
Completion Date
21-Jul-2014
Directive
2004/108/EC - Directive 2004/108/EC of the European Parliament and of the Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
2004/108/EU - DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC
89/336/EEC - Electromagnetic compatibility (EMC)
Ref Project
SIST EN 60265-1:2001 - High-voltage switches -- Part 1: Switches for rated voltages above 1 kV and less than 52 kV

Relations

Replaced By
EN 62271-103:2011 - High-voltage switchgear and controlgear - Part 103: Switches for rated voltages above 1 kV up to and including 52 kV
Effective Date
28-Jan-2023

Buy Standard

EN 60265-1:2001EN 60265-1:2001
PreviousNext
Standard
EN 60265-1:2001
English language
55 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60265-1:2001
01-marec-2001
High-voltage switches - Part 1: Switches for rated voltages above 1 kV and less
than 52 kV
High-voltage switches -- Part 1: Switches for rated voltages above 1 kV and less than 52
kV
Hochspannungs-Lastschalter -- Teil 1: Hochspannungs-Lastschalter für
Nennspannungen über 1 kV und unter 52 kV
Interrupteurs à haute tension -- Partie 1: Interrupteurs pour tensions assignées
supérieures à 1 kV et inférieures à 52 kV
Ta slovenski standard je istoveten z: EN 60265-1:1998
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 60265-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 2 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 3 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 4 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 5 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 6 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 7 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 8 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 9 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 10 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 11 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 12 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 13 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 14 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 15 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 16 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 17 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 18 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 19 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 20 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 21 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 22 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 23 ----------------------

SIST EN 60265-1:2001

---------------------- Page: 24 ----------------------

SIST EN 60265-1:2001

-------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60669-2-1:2022/AC:2024-01(Corrigendum)
Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices
SIST EN IEC 60669-2-1:2023/AC:2024
  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-2:2023/AC:2023-07(Corrigendum)
Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
SIST EN IEC 60947-6-2:2023/AC:2023
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-1:2023(Main)
Low-voltage switchgear and controlgear - Part 6-1: Multiple function equipment - Transfer switching equipment
SIST EN IEC 60947-6-1:2023

This part of EN 60947applies to transfer switching equipment (TSE) to be used in power systems with interruption of the supply to the load during transfer, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-6-2:2023(Main)
Low-voltage switchgear and controlgear - Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
SIST EN IEC 60947-6-2:2023

Applies to control and protective switching devices (or equipment) (CPS), the main contacts of which are intended to be connected to circuits of rated voltage not exceeding 1 000 V a.c. or 1 500 V d.c. CPSs are intended to provide both protective and control functions for circuits and are operated otherwise than by hand. They may also fulfil additional functions, such as isolation.

  • Standard
    116 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60669-2-1:2022/A11:2022(Amendment)
Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices
SIST EN IEC 60669-2-1:2023/A11:2023

To give requirements and tests for electronic control devices, a general term to cover electronic switches, HBES/BACS switches and electronic extension units. It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors. It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC. This Part of IEC 60669 also applies to electronic control devices which include integrated radio receivers and transmitters.

  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60669-2-1:2022(Main)
Switches for household and similar fixed electrical installations - Part 2-1: Particular requirements - Electronic control devices
SIST EN IEC 60669-2-1:2023

This clause of Part 1 is completely replaced by the following: This part of IEC 60669 applies to electronic control devices, a general term to cover electronic switches, home and building electronic systems (HBES) / building automation and control systems (BACS) switches and electronic extension units. It applies to electronic switches and to HBES/BACS switches, for alternating current (AC) only with a rated switching voltage not exceeding 250 V and a rated current not exceeding 16 A, intended for household and similar fixed electrical installations, either indoors or outdoors. It also applies to electronic extension units with a rated supply voltage not exceeding 250 V AC and 120 V DC, such as sensors and push buttons. This document also applies to electronic remote control switches (RCS) and electronic time delay switches (TDS). Particular requirements are given in Annex FF. Switches including only passive components such as resistors, capacitors, inductors, positive temperature coefficient (PTC) and negative temperature coefficient (NTC) components, varistors, printed wiring boards and connectors are not considered as electronic control devices. This document also applies to electronic switches and HBES/BACS switches for the operation of lighting equipment circuits and the control of the brightness of lighting equipment (dimmers) as well as the control of the speed of motors (for example, those used in ventilating fans) and for other purposes (for example, heating controls). The operation and/or control as mentioned above can be transmitted by an electronic signal via several media, for example, powerline (mains), twisted pair, optical fibre, radio frequency, infrared, etc. and are performed: - intentionally by a person via an actuating member, a key, a card, etc., via a sensing surface or a sensing unit, by means of touch, proximity, turn, optical, acoustic, thermal; - by physical means, for example, light, temperature, humidity, time, wind velocity, presence of people; - by any other influence. This document also applies to electronic control devices which include integrated radio receivers and transmitters. This document covers only those requirements for mounting boxes which are necessary for the tests on the electronic control devices. Requirements for general purpose mounting boxes are given in the relevant part, if any, of IEC 60670. This document is not intended to cover devices falling within the scope of IEC 60730 (all parts). Electronic control devices complying with this document are suitable for use at ambient temperature not normally exceeding 25 °C but occasionally reaching 35 °C with a lower limit of the ambient air temperature of −5 °C. NOTE 1 For lower temperatures, see Annex E. Functional safety aspects are not covered by this document. Functional safety requirements are covered by the standards of the controlled devices. In locations where special conditions prevail, such as in ships, vehicles and the like and in hazardous locations, for example where explosions are liable to occur, special construction and/or additional requirements may be required. This document is not intended to cover devices which are designed to be incorporated in appliances or are intended to be delivered together with a specific appliance and which are within the scope of IEC 60730 (all parts) or IEC 61058-1. Examples of designs of electronic switches and HBES/BACS switches and functions are shown in Annex AA. Additional requirements for electronic control devices using DLT-technology in accordance with IEC 62756-1 are given in Annex CC. Electrical interface specification for phase-cut dimmer used in phase-cut dimmed lighting systems are given for information only in Annex EE. NOTE 2 Electronic switches and HBES/BACS switches without a mechanical switch in the main circuit do not provide a "full off-state". Therefore, the circuit on the load side are to be considered to be live.

  • Standard
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-5-2:2020/A11:2022(Amendment)
Low-voltage switchgear and controlgear - Part 5-2: Control circuit devices and switching elements - Proximity switches
SIST EN IEC 60947-5-2:2020/A11:2022

EN-IEC 60947-5-2 applies to inductive and capacitive proximity switches that sense the presence of metallic and/or non-metallic objects, ultrasonic proximity switches that sense the presence of sound reflecting objects, photoelectric proximity switches that sense the presence of objects and non-mechanical magnetic proximity switches that sense the presence of objects with a magnetic field. Products covered by the scope of this document are not subjected to defined behaviours under fault conditions. Proximity switches with defined behaviour are covered by IEC 60947-5-3 and have to fulfil additional requirements. These proximity switches are self-contained, have semiconductor switching element(s) and are intended to be connected to circuits, the rated voltage of which does not exceed 250 V 50 Hz/60 Hz AC RMS or 300 V DC. Examples of typical applications for in-scope products: - factory automation and machinery industry; - logistic and packaging industry; - conveyor belts, lifts; - process industry; - power plants. Special applications (e.g. corrosive atmosphere) can cause additional requirements. This document is not intended to cover proximity switches with analogue outputs. The object of this document is to state for proximity switches: - definitions; - classification; - characteristics; - product information; - normal service, mounting and transport conditions; - constructional and performance requirements; - tests to verify rated characteristics. Products covered by the scope of this document are expected to be selected, installed, and maintained by skilled personnel only.

  • Amendment
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-3:2021/AC:2021-11(Corrigendum)
Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
SIST EN IEC 60947-3:2021/AC:2022

IEC corrected version

  • Corrigendum
    3 pages
    English and French language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60947-3:2021(Main)
Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
SIST EN IEC 60947-3:2021

IEC 60947-3:2020 applies to switches, disconnectors, switch-disconnectors and fuse-combination units and their dedicated accessories to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2008, Amendment 1:2012 and Amendment 2:2015. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:  
addition of critical load current tests for DC switches (see 9.3.9);
addition of requirements for a conditional short-circuit rating for disconnectors, switches, and switch-disconnectors protected by circuit-breakers (see 9.3.7.2);
addition of new categories for high-efficiency motors switching (see Annex A);
addition of new Annex E for connection to aluminium conductors;
addition of new Annex F for power losses measurement.

  • Standard
    99 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    99 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 61058-2-5:2021(Main)
Switches for appliances - Part 2-5: Particular requirements for change-over selectors
SIST EN IEC 61058-2-5:2021

IEC 61058-2-5:2018 is available as IEC 61058-2-5:2018 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61058-2-5:2018 applies to change-over selectors (mechanical or electronic) for appliances actuated by hand, by foot or by other human activity, to operate or control electrical appliances and other equipment for household or similar purposes with a rated voltage not exceeding 480 V and a rated current not exceeding 63 A. This third edition cancels and replaces the second edition published in 2010 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - updated references due to new structure of IEC 61058-1; - changes on conducting the heating test due to the corresponding changes in IEC 61058-1.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day