EN 61193-3:2013

Quality assessment systems - Part 3: Selection and use of sampling plans for printed board and laminate end-product and in-process auditing

IEC 61193-3:2013 establishes sampling plans for inspection by attributes, including sample plan selection criteria and implementation procedures for printed board and laminate end-product and in-process auditing. The principles established herein permit the use of different sampling plans that may be applied to an individual attribute or set of attributes, according to classification of importance with regard to form, fit and function.

Qualitätsbewertungssysteme - Teil 3: Auswahl und Anwendung von Stichprobenanweisungen für Endprodukte von Leiterplatten und Laminaten und fertigungsbegleitende Auditierung

Système d'assurance de la qualité - Partie 3: Choix et utilisation de plans d'échantillonnage pour cartes imprimées et produits finis stratifiés et audits en cours de fabrication

La CEI 61193-3:2013 établit des plans d'échantillonnage pour le contrôle par attributs, incluant des critères de sélection de plans d'échantillonnage et des procédures de mise en oeuvre pour les cartes imprimées et les produits finis stratifiés et des audits en cours de fabrication. Les principes établis ici permettent d'utiliser différents plans d'échantillonnage qui peuvent être appliqués à un seul attribut ou à un ensemble d'attributs, selon une classification sur l'importance portant sur la forme, le caractère adapté et la fonction.

Sistemi ocenjevanja kakovosti - 3. del: Izbira in uporaba planov vzorčenja za pregledovanje tiskanih plošč in laminatov končnih izdelkov in presojanje med procesom

Ta del standarda IEC 61193 vzpostavlja plane vzorčenja za kontrolo po opisnih spremenljivkah, vključno s kriteriji za izbor plana vzorčenja in postopki izvajanja za tiskane plošče in laminate končnih izdelkov ter presojanje med procesom. Načela, ki so določena tukaj, dovoljujejo uporabo različnih planov vzorčenja, ki se lahko uporabljajo za posamezno lastnost ali nabor lastnosti glede na klasifikacijo pomembnosti, ki upošteva obliko, prileganje in funkcijo.

General Information

• Status: Published
• Publication Date: 25-Apr-2013
• Withdrawal Date: 27-Feb-2016
• ICS: 31.190 - Electronic component assemblies
• Technical Committee: CLC/SR 91 - Electronics assembly technology
• Drafting Committee: IEC/TC 91 - IEC_TC_91
• Parallel Committee: IEC/TC 91 - IEC_TC_91
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 26-Apr-2013
• Completion Date: 26-Apr-2013
• Ref Project: SIST EN 61193-3:2013 - Quality assessment systems - Part 3: Selection and use of sampling plans for printed boards and laminate end-products and in-process auditing

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2013
6LVWHPLRFHQMHYDQMDNDNRYRVWLGHO,]ELUDLQXSRUDEDSODQRYY]RUþHQMD]D
SUHJOHGRYDQMHWLVNDQLKSORãþLQODPLQDWRYNRQþQLKL]GHONRYLQSUHVRMDQMHPHG
SURFHVRP
Quality assessment systems - Part 3: Selection and use of sampling plans for printed
boards and laminate end-products and in-process auditing
Qualitätsbewertungssysteme - Teil 3: Auswahl und Anwendung von
Stichprobenanweisungen für Endprodukte von Leiterplatten und Laminaten und
fertigungsbegleitende Auditierung
Système d'assurance de la qualité - Partie 3: Choix et utilisation de plans
d'échantillonnage pour cartes imprimées et produits finis stratifiés et audits en cours de
fabrication
Ta slovenski standard je istoveten z: EN 61193-3:2013
ICS:
03.120.99 Drugi standardi v zvezi s Other standards related to
kakovostjo quality
31.180 7LVNDQDYH]MD7,9LQWLVNDQH Printed circuits and boards
SORãþH
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61193-3
NORME EUROPÉENNE
April 2013
EUROPÄISCHE NORM
ICS 31.190
English version
Quality assessment systems -
Part 3: Selection and use of sampling plans for printed board and laminate
end-product and in-process auditing
(IEC 61193-3:2013)
Système d'assurance de la qualité -  Qualitätsbewertungssysteme -
Partie 3: Choix et utilisation de plans Teil 3: Auswahl und Anwendung von
d'échantillonnage pour cartes imprimées Stichprobenanweisungen für Endprodukte
et produits finis stratifiés et audits en von Leiterplatten und Laminaten und
cours de fabrication fertigungsbegleitende Auditierung
(CEI 61193-3:2013) (IEC 61193-3:2013)

This European Standard was approved by CENELEC on 2013-02-28. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61193-3:2013 E
Foreword
The text of document 91/1061/FDIS, future edition 1 of IEC 61193-3, prepared by IEC TC 91 "Electronics
assembly technology" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has (dop) 2013-11-28
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2016-02-28
• latest date by which the national
standards conflicting with the

document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61193-3:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-2-20 NOTE  Harmonized as EN 60068-2-20.
IEC 60068-2-38 NOTE  Harmonized as EN 60068-2-38.
IEC 61189-2 NOTE  Harmonized as EN 61189-2.
IEC 61189-3 NOTE  Harmonized as EN 61189-3.
IEC 61193-1 NOTE  Harmonized as EN 61193-1.
IEC 61193-2 NOTE  Harmonized as EN 61193-2.
IEC 62326-1 NOTE  Harmonized as EN 62326-1.
IEC 62326-4-1 NOTE  Harmonized as EN 62326-4-1.
ISO 14001 NOTE  Harmonized as EN ISO 14001.

- 3 - EN 61193-3:2013
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60194 2006 Printed board design, manufacture and EN 60194 2006
assembly - Terms and definitions

IEC 62326-4 1996 Printed boards - EN 62326-4 1997
Part 4: Rigid multilayer printed boards with
interlayer connections - Sectional specification

ISO 9000 2005 Quality management systems - Fundamentals EN ISO 9000 2005
and vocabulary
ISO 14560 2004 Acceptance sampling procedures - -
by attributes - Specified quality levels in
nonconforming items per million

IEC 61193-3 ®
Edition 1.0 2013-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Quality assessment systems –
Part 3: Selection and use of sampling plans for printed board and laminate end-

product and in-process auditing

Système d'assurance de la qualité –

Partie 3: Choix et utilisation de plans d'échantillonnage pour cartes imprimées et

produits finis stratifiés et audits en cours de fabrication

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX XB
ICS 31.190 ISBN 978-2-83220-585-3

– 2 – 61193-3 © IEC:2013
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references. 7
3 Terms and definitions . 7
4 Sampling methodologies . 9
4.1 General . 9
4.2 Attribute sampling plans. 10
4.2.1 General . 10
4.2.2 Continuous sampling. 10
4.2.3 Production lot attributes . 10
4.2.4 Production lot variables . 10
4.3 Non-statistical sampling plans . 11
4.4 Defining c = 0 plans . 11
5 Classification of attributes . 16
5.1 General . 16
5.2 Classification assignment . 17
5.3 Classification and adjustment of sampling plan criteria . 18
5.4 Process control . 18
6 Defects and process deviation indicator (PDI) evaluation . 19
6.1 General . 19
6.2 Process control and process improvement requirements . 19
7 Inspection plans . 19
7.1 General . 19
7.2 Zero acceptance number-based sampling plans . 20
7.3 Responsible authority . 20
7.4 Application. 20
7.5 Sampling plan specification . 20
7.6 Submission of product . 21
8 Classification of defects . 23
8.1 General . 23
8.2 Customers detail specification (CDS) data . 23
9 Percent defectives per million opportunities . 23
9.1 General . 23
9.2 Classes of DPMO . 24
9.2.1 General . 24
9.2.2 DPMO-1 – Functional non-conformances only . 24
9.2.3 DPMO-2 – Electrical non-conformances . 24
9.2.4 DPMO-3 – Visual/mechanical non-conformances . 24
9.2.5 DPMO-4 – hermetic non-conformances . 24
9.2.6 DPMO-5 – all non-conformances . 24
9.3 Estimation of DPMO . 24
9.3.1 General . 24
9.3.2 DPMO reporting . 24
9.4 DPMO calculations . 25

61193-3 © IEC:2013 – 3 –
9.4.1 General . 25
9.4.2 Sampling requirements . 25
10 Use of sampling plans . 25
10.1 General . 25
10.2 Grouping of tests . 25
10.3 Categorization . 26
10.4 In-process testing and control . 26
10.5 Indirect measuring methods . 27
Annex A (informative) Example of consensus sampling plan for three levels of
conformance to requirements of IEC 62326-4 multilayer printed boards . 28
Annex B (informative) Example of consensus sampling plan . 49
Annex C (informative) Operating characteristics curves and values . 52
Bibliography . 60

Figure 1 – Typical OC curve for c ≥ 0 plan . 13
Figure 2 – OC curve comparisons between c ≥ 0 and c = 0 plans . 14
Figure 3 – Systematic path for implementing process control . 19
Figure
...