EN 60332-3-10:2009
(Main)Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus
Tests on electric and optical fibre cables under fire conditions - Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or cables - Apparatus
IEC 60332-3-10:2000 Specifies method of test for the assessment of vertical flame spread of vertically-mounted bunched wires or cables, electrical or optical, under defined conditions. Gives details of the apparatus and its arrangement and calibration. It has the status of a horizontal standard in accordance with IEC Guide 104
Prüfungen an Kabeln, isolierten Leitungen und Glasfaserkabeln im Brandfall - Teil 3-10: Prüfung der vertikalen Flammenausbreitung von vertikal angeordneten Bündeln von Kabeln und isolierten Leitungen - Prüfvorrichtung
Essais des câbles électriques et des câbles à fibres optiques soumis au feu - Partie 3-10: Essai de propagation verticale de la flamme des fils ou câbles montés en nappes en position verticale - Appareillage
Preskusi na električnih kablih in kablih iz optičnih vlaken v požarnih razmerah - 3-10. del: Preskus navpičnega širjenja ognja po navpično pritrjenih snopih žic ali kablov - Preskuševalna naprava (IEC 60332-3-10:2000 + A1:2008 )
Ta serija mednarodnega standarda, zajeta v 3-10., 3-21., 3-22. 3-23., 3-24. in 3-25. delu IEC 60332, določa preskusne metode za ocenjevanje navpičnega širjenja ognja po navpično pritrjenih snopih žic ali kablov, električnih ali optičnih, pod določenimi pogoji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2010
1DGRPHãþD
SIST EN 50266-1:2002
3UHVNXVLQDHOHNWULþQLKNDEOLKLQNDEOLKL]RSWLþQLKYODNHQYSRåDUQLKUD]PHUDK
GHO 3UHVNXVQDYSLþQHJDãLUMHQMDRJQMDSRQDYSLþQRSULWUMHQLKVQRSLKåLFDOL
NDEORY3UHVNXãHYDOQDQDSUDYD ,(& $
Tests on electric and optical fibre cables under fire conditions -- Part 3-10: Test for
vertical flame spread of vertically-mounted bunched wires or cables - Apparatus
Prüfungen an Kabeln, isolierten Leitungen und Glasfaserkabeln im Brandfall -- Teil 3-10:
Prüfung der vertikalen Flammenausbreitung von vertikal angeordneten Bündeln von
Kabeln und isolierten Leitungen - Prüfvorrichtung
Essais des câbles électriques et des câbles à fibres optiques soumis au feu -- Partie 3-
10: Essai de propagation verticale de la flamme des fils ou câbles montés en nappes en
position verticale - Appareillage
Ta slovenski standard je istoveten z: EN 60332-3-10:2009
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.060.20 Kabli Cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60332-3-10
NORME EUROPÉENNE
October 2009
EUROPÄISCHE NORM
ICS 29.060.20, 13.220.40; 29.020 Supersedes EN 50266-1:2001 + corr. March 2002
English version
Tests on electric and optical fibre cables under fire conditions -
Part 3-10: Test for vertical flame spread
of vertically-mounted bunched wires or cables -
Apparatus
(IEC 60332-3-10:2000 + A1:2008)
Essais des câbles électriques Prüfungen an Kabeln, isolierten Leitungen
et des câbles à fibres optiques und Glasfaserkabeln im Brandfall -
soumis au feu - Teil 3-10: Prüfung der vertikalen
Partie 3-10: Essai de propagation verticale Flammenausbreitung von vertikal
de la flamme des fils ou câbles angeordneten Bündeln von Kabeln
montés en nappes en position verticale - und isolierten Leitungen -
Appareillage Prüfvorrichtung
(CEI 60332-3-10:2000 + A1:2008) (IEC 60332-3-10:2000 + A1:2008)
This European Standard was approved by CENELEC on 2009-08-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60332-3-10:2009 E
Foreword
The text of the International Standard IEC 60332-3-10:2000 and its amendment A1:2008, prepared by
IEC TC 20, Electric cables, was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as EN 60332-3-10 on 2009-08-01 without any modification.
This European Standard supersedes EN 50266-1:2001 + corrigendum March 2002.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-08-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60332-3-10:2000 and its amendment A1:2008 was
approved by CENELEC as a European Standard without any modification.
__________
– 3 – EN 60332-3-10:2009
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60695-4 - Fire hazard testing - EN 60695-4 2006
Part 4: Terminology concerning fire tests
1)
IEC Guide 104 - The preparation of safety publications and - -
the use of basic safety publications and
group safety publications
———————
1)
Undated reference.
2)
Valid edition at date of issue.
IEC 60332-3-10 ®
Edition 1.1 2009-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
GROUP SAFETY PUBLICATION
PUBLICATION GROUPÉE DE SÉCURITÉ
Tests on electric and optical fibre cables under fire conditions –
Part 3-10: Test for vertical flame spread of vertically-mounted bunched wires or
cables – Apparatus
Essais des câbles électriques et des câbles à fibres optiques soumis au feu –
Partie 3-10: Essai de propagation verticale de la flamme des fils ou câbles
montés en nappes en position verticale – Appareillage
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CE
CODE PRIX
ICS 29.060.20;13.220.40; 29.020 ISBN 2-8318-1029-4
– 2 – 60332-3-10 © IEC:2000+A1:2008
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references.6
3 Definitions .6
4 Test environment.6
5 Test apparatus .7
5.1 Test chamber .7
5.2 Air supply .7
5.3 Ladder types.7
5.4 Effluent cleaning attachment.7
6 Ignition source .8
6.1 Type.8
6.2 Positioning.9
Annex A (informative) Details of recommended burner .18
Annex B (informative) Flowmeter calibration correction factors .19
Figure 1 – Test chamber .11
Figure 2 – Thermal insulation of back and sides of the test chamber.12
Figure 3 – Positioning of burner and typical arrangement of test sample on ladder .13
Figure 4 – Tubular steel ladders for cable test .14
Figure 5 – Burner configurations.15
Figure 6 – Arrangement of holes for burners.16
Figure 7 – Schematic diagram of an example of a burner control system using rotameters.17
60332-3-10 © IEC:2000+A1:2008 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES
UNDER FIRE CONDITIONS –
Part 3-10: Test for vertical flame spread of vertically-mounted bunched
wires or cables – Apparatus
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60332-3-10 has been prepared by IEC technical committee 20:
Electric cables.
It has the status of a group safety publication in accordance with IEC Guide 104.
IEC 60332-3-10 forms one of a series of publications dealing with tests on electric cables
under fire conditions; the series supersedes IEC 60332-3 published in 1992. The parts of the
series are described in the introduction.
All pre-existing categories of test are retained and updated. A new category (category D) has
been added to cater for testing at very low non-metallic volumes.
– 4 – 60332-3-10 © IEC:2000+A1:2008
This consolidated version of IEC 60332-3-10 consists of the first edition (2000) [documents
20/402/FDIS and 20/426/RVD] and its amendment 1 (2008) [documents 20/933/CDV and
20/982A/RVC].
The technical content is therefore identical to the base edition and its amendment and has
been prepared for user convenience.
It bears the edition number 1.1.
A vertical line in the margin shows where the base publication has been modified by
amendment 1.
Annexes A and B are for information only.
The committee has decided that the contents of the base publication and its amendments will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date,
the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
60332-3-10 © IEC:2000+A1:2008 – 5 –
I
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.