EN 60172:1994/A2:2010
(Amendment)Test procedure for the determination of the temperature index of enamelled winding wires
Test procedure for the determination of the temperature index of enamelled winding wires
Prüfverfahren zur Bestimmung des Temperaturindex von Lackdrähten
Méthode d'essai pour la détermination de l'indice de température des fils de bobinage émaillés
Preskusni postopek za določanje temperaturnega indeksa emajlirane žice za navitja (IEC 60172:1987/A2:2010)
Amandma A2:2010 je dodatek k standardu SIST EN 60172:2001
Ta preskusni postopek v skladu z določbami objave IEC 216-1 določa metodo za vrednotenje temperaturnega indeksa okrogle emajlirane žice za navitja. Ne velja za žico za navitja pravokotnega prereza ali z vlakni izolirano žico za navitja. Izkušnje so pokazale, da se nepotrebni krhkosti preskusnih vzorcev izognemo z velikostmi med 0,8 mm in 1,5 mm, ki so v splošnem primerne za delo in preskušanje.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2010
3UHVNXVQLSRVWRSHN]DGRORþDQMHWHPSHUDWXUQHJDLQGHNVDHPDMOLUDQHåLFH]D
QDYLWMD ,(& $
Test procedure for the determination of the temperature index of enamelled winding
wires (IEC 60172:1987/A2:2010)
Prüfverfahren zur Bestimmung des Temperaturindex von Lackdrähten (IEC
60172:1987/A2:2010)
Méthode d'essai pour la détermination de l'indice de température des fils de bobinage
émaillés (CEI 60172:1987/A2:2010)
Ta slovenski standard je istoveten z: EN 60172:1994/A2:2010
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 60172/A2
NORME EUROPÉENNE
February 2010
EUROPÄISCHE NORM
ICS 29.060.10
English version
Test procedure for the determination of the temperature index
of enamelled winding wires
(IEC 60172:1987/A2:2010)
Méthode d'essai pour la détermination Prüfverfahren zur Bestimmung
de l'indice de température des fils des Temperaturindex von Lackdrähten
de bobinage émaillés (IEC 60172:1987/A2:2010)
(CEI 60172:1987/A2:2010)
This amendment A2 modifies the European Standard EN 60172:1994; it was approved by CENELEC on 2010-
02-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate
the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: Avenue Marnix 17, B - 1000 Brussels
© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60172:1994/A2:2010 E
Foreword
The text of document 55/1140/CDV, future amendment 2 to IEC 60172:1987, prepared by IEC TC 55,
Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
amendment A2 to EN 60172:1994 on 2010-02-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
an identical national standard or by endorsement (dop) 2010-11-01
– latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2013-02-01
__________
Endorsement notice
The text of amendment 2:2010 to the International Standard IEC 60172:1987 was approved by
CENELEC as an amendment to the European Standard without any modification.
__________
IEC 60172 ®
Edition 3.0 2010-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Test procedure for the determination of the temperature index of enamelled
winding wires
Méthode d'essai pour la détermination de l'indice de température des fils de
bobinage émaillés
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
F
CODE PRIX
ICS 29.060.10 ISBN 2-8318-1074-7
– 2 – 60172 Amend. 2 © IEC:2010
FOREWORD
This amendment has been prepared by IEC technical committee 55: Winding wires.
The text of this amendment is based on the following documents:
CDV Report on voting
55/1140/CDV 55/1174/RVC
Full information on the voting for the approval of this amendment can be found in the report on
voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the maintenance result date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
5 Test specimens
5.1.1 Enamelled round wire with a nominal conductor diameter of 0,800 mm up to and
including 1,500 mm
Replace the title and text of this subclause by the following:
5.1.1 Enamelled round wire with a nominal conductor diameter of 0,224 mm up to and
including 2,65 mm
The grade of insulation used for determining the thermal index shall be grade 2 or grade 2B for
self-bonding winding wires.
Wire sizes 0,315 mm and 0,28 mm are permitte
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.