EN 60384-17-1:2005

Fixed capacitors for use in electronic equipment - Part 17-1: Blank detail specification - Fixed metallized polypropylene film dielectric a.c. and pulse capacitors - Assessment levels E and EZ

blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of details specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they be so described.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 17-1: Vordruck für Bauartspezifikation - Festkondensatoren mit metallisierter Polypropylen-Folie als Dielektrikum für Wechselspannungs- und Impulsbetrieb - Qualitätsbewertungsstufen E und EZ

Condensateurs fixes utilisés dans les équipements électroniques - Partie 17-1: Spécification particulière cadre: Condensateurs fixes pour tension alternative et pour impulsions à diélectrique en film de polypropylène métallisé - Niveaux d'assurances E et EZ

Nespremenljivi kondenzatorji za uporabo v elektronski opremi – 17-1. del: Okvirna podrobna specifikacija – Nespremenljivi kondenzatorji z dielektrikom iz metalizirane polipropilenske folije za izmenične napetosti in impulzni kondenzatorji – Ocenjevalna nivoja E in EZ (IEC 60384-17-1:2005)

General Information

• Status: Published
• Publication Date: 08-Dec-2005
• Withdrawal Date: 31-Oct-2008
• ICS: 31.060.30 - Paper and plastics capacitors
• Technical Committee: CLC/TC 40XA - CLC/TC 40XA
• Drafting Committee: IEC/TC 40 - IEC_TC_40
• Parallel Committee: IEC/TC 40 - IEC_TC_40
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 09-Dec-2005
• Completion Date: 09-Dec-2005
• Ref Project: SIST EN 60384-17-1:2006 - Fixed capacitors for use in electronic equipment -- Part 17-1: Blank detail specification - Fixed metallized polypropylene film dielectric a.c. and pulse capacitors - Assessment levels E and EZ

Standards Content (Sample)

SLOVENSKI SIST EN 60384-17-1:2006

STANDARD
februar 2006
Nespremenljivi kondenzatorji za uporabo v elektronski opremi – 17-1. del:
Okvirna podrobna specifikacija – Nespremenljivi kondenzatorji z dielektrikom
iz metalizirane polipropilenske folije za izmenične napetosti in impulzni
kondenzatorji – Ocenjevalna nivoja E in EZ (IEC 60384-17-1:2005)
Fixed capacitors for use in electronic equipment – Part 17-1: Blank detail
specification – Fixed metallized polypropylene film dielectric a.c. and pulse
capacitors – Assessment levels E and EZ (IEC 60384-17-1:2005)
ICS 31.060.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 60384-17-1
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2005

ICS 31.060.30
English version
Fixed capacitors for use in electronic equipment
Part 17-1: Blank detail specification:
Fixed metallized polypropylene film dielectric a.c. and pulse capacitors -
Assessment levels E and EZ
(IEC 60384-17-1:2005)
Condensateurs fixes utilisés  Festkondensatoren zur Verwendung in
dans les équipements électroniques Geräten der Elektronik
Partie 17-1: Spécification particulière Teil 17-1: Vordruck für Bauartspezifikation:
cadre: Condensateurs fixes pour tension Festkondensatoren mit metallisierter
alternative et pour impulsions à Polypropylen-Folie als Dielektrikum für
diélectrique en film de polypropylène Wechselspannungs- und Impulsbetrieb -
métallisé – Qualitätsbewertungsstufen E und EZ
Niveaux d'assurances E et EZ (IEC 60384-17-1:2005)
(CEI 60384-17-1:2005)
This European Standard was approved by CENELEC on 2005-11-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60384-17-1:2005 E
Foreword
The text of document 40/1598/FDIS, future edition 2 of IEC 60384-17-1, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 60384-17-1 on 2005-11-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-08-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-11-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60384-17-1:2005 was approved by CENELEC as a
European Standard without any modification.
__________
- 3 - EN 60384-17-1:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 60384-1 - Fixed capacitors for use in electronic EN 60384-1 2001
(mod) equipment + corr. October 2001
Part 1: Generic specification
1) 2)
IEC 60384-17 - Part 17: Sectional specification: Fixed EN 60384-17 2005
metallized polypropylene film dielectric
a.c. and pulse capacitors
1)
Undated reference.
2)
Valid edition at date of issue.

INTERNATIONAL IEC
STANDARD
60384-17-1
QC 301301
Second edition
2005-11
Fixed capacitors for use in electronic equipment –
Part 17-1:
Blank detail specification:
Fixed metallized polypropylene film
dielectric a.c. and pulse capacitors –
Assessment levels E and EZ
 IEC 2005  Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale P
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
For price, see current catalogue

– 2 – 60384-17-1  IEC:2005(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 17-1: Blank detail specification: Fixed metallized polypropylene
film dielectric a.c. and pulse capacitors –
Assessment levels E and EZ
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-17-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This second edition cancels and replaces the first edition published in 1987 and constitutes
minor revisions related to tables, figures and references.
The text of this standard is based on the following documents:
FDIS Report on voting
40/1598/FDIS 40/1631/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

60384-17-1  IEC:20205(E) – 3 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
IEC 60384 consists of the following parts, under the (new) general title Fixed capacitors for
use in electronic equipment:
Part 1: Generic specification
Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
d.c. capacitors
Part 3: Sectional specification: Fixed tantalum chip capacitors
Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid
electrolyte
Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage
not exceeding 3000 V – Selection of methods of test and general requirements
Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c.
capacitors
Part 7: Sectional specification: Fixed polystyrene film dielectric metal foil d.c. capacitors
Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1
Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil
d.c. capacitors
Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c.
capacitors
Part 13:  Sectional specification: Fixed polypropylene film dielectric metal foil d.c.
capacitors
Part 14: Sectional specification: Fixed capacitors for electromagnetic interference
suppression and connection to the supply mains
Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid
electrolyte
Part 16: Sectional specification: Fixed metallized polypropylene film dielectric d.c.
capacitors
Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and
pulse capacitors
Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and
non-solid electrolyte
Part 19: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric
chip d.c. capacitors
Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric chip
d.c. capacitors
Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 1
Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic
dielectric, Class 2
Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate
film dielectric d.c. capacitors
Part 24: Sectional specification – Surface mount fixed tantalum electrolytic capacitors with
conductive polymer solid electrolyte (under consideration)
Part 25: Sectional specification – Surface mount fixed aluminium electrolytic capacitors
with conductive polymer solid electrolyte (under consideration)
All sectional specifications mentioned above do have one or more blank detail specifications
being a supplementary document, containing requirements for style, layout and minimum
content of detail specifications.

– 4 – 60384-17-1  IEC:2005(E)
The QC 301301 number that appears on the front cover of this publication is the specification
number in the IECQ Quality Assessment System for Electronic Components.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

60384-17-1  IEC:20205(E) – 5 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 17-1: Blank detail specification: Fixed metallized polypropylene
film dielectric a.c. and pulse capacitors –
Assessment levels E and EZ
INTRODUCTION
Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style and layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they be so described.
In the preparation of detail specifications the content of 1.4 of the sectional specification shall
be taken into account.
The numbers between brackets on the first page correspond to the following information
which shall be inserted in the position indicated:
Identification of the detail specification
[1] The "International Electrotechnical Commission" or the National Standards
...