EN 61029-2-1:2012
(Main)Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saw benches
Safety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saw benches
Applies to transportable circular saws intended for cutting wood and similar materials with a blade diameter not exceeding 260 mm.
Sicherheit transportabler motorbetriebener Elektrowerkzeuge - Teil 2-1: Besondere Anforderungen an Tischkreissägen
Sécurité des machines-outils électriques semi-fixes - Partie 2-1: Règles particulières pour les scies circulaires à table
S'applique aux scies circulaires semi-fixes, destinées à couper du bois et des matériaux similaires et ayant un diamètre de lame maximal de 260 mm.
Varnost premičnih električnih orodij - 2-1. del: Posebne zahteve za krožne žage z delovno mizo
Ta mednarodni standard se uporablja za premične krožne žage, namenjene rezanju lesa in podobnih materialov, katerih premer rezila je manjši od 260 mm, kot je določeno v točki 2.101.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Sicherheit transportabler motorbetriebener Elektrowerkzeuge - Teil 2-1: Besondere Anforderungen an TischkreissägenSécurité des machines outils électrique semi-fixes - Partie 2-1: Règles particulières pour les scies circulaires à tableSafety of transportable motor-operated electric tools - Part 2-1: Particular requirements for circular saw benches25.140.20Electric tools25.080.60Strojne žageSawing machinesICS:Ta slovenski standard je istoveten z:EN 61029-2-1:2012SIST EN 61029-2-1:2013en01-marec-2013SIST EN 61029-2-1:2013SLOVENSKI
STANDARD
EUROPEAN STANDARD EN 61029-2-1 NORME EUROPÉENNE
EUROPÄISCHE NORM October 2012
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2012 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61029-2-1:2012 E
ICS 25.140.20 Supersedes EN 61029-2-1:2010
English version
Safety of transportable motor-operated electric tools -
Part 2-1: Particular requirements for circular saw benches (IEC 61029-2-1:1993, modified + A1:1999 + A2:2001)
Sécurité des machines-outils électriques semi-fixes -
Partie 2-1: Règles particulières pour les scies circulaires à table (CEI 61029-2-1:1993, modifiée + A1:1999 + A2:2001)
Sicherheit transportabler motorbetriebener Elektrowerkzeuge -
Teil 2-1: Besondere Anforderungen an Tischkreissägen (IEC 61029-2-1:1993, modifiziert + A1:1999 + A2:2001)
This European Standard was approved by CENELEC on 2012-09-03. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Normative references . 28Annex ZD (informative)
Dust measurement . 29Annex ZZ (informative)
Coverage of Essential Requirements of Directive 2006/42/EC . 31
– 3 – EN 61029-2-1:2012 Figures Figure Z101 – Example of circular saw bench . 17Figure Z102 – Riving knife mounted guard . 17Figure Z103 – Example of ribbing on guard side walls . 18Figure Z104 – Saw blade guard − Stability test
.................................................................... 19Figure Z105 – Test probe ...................................................................................................... 21Figure Z106 – Riving knife adjustment ................................................................................... 21Figure Z107 – Riving knife testing – Strength of riving knife mounting .................................... 22Figure Z108 – Riving knife testing – Resiliency of riving knife ................................................ 23Figure Z109 – Dimensions of the saw table ........................................................................... 24Figure Z110 – Dimension of the slot in the table .................................................................... 25Figure Z111 – Guiding surfaces of the rip fence ..................................................................... 25Figure Z112 – Flange characteristics ..................................................................................... 26Figure Z113 – Examples for push-stick and push block handle .............................................. 27Figure ZD.101 – Orientation of tool and operator ................................................................... 30 Tables Table Z101 – Noise test conditions for circular saw benches.................................................... 9Table ZD.101 – Conditions for dust measurements ................................................................ 29 SIST EN 61029-2-1:2013
– change of Subclause 13.1 into Annex ZD. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights. This European Standard is divided into two parts: Part 1 General requirements, which are common to most transportable motor, operated tools (for the purpose of this European Standard referred to simply as tools) which could come within the scope of this European Standard. Part 2 Requirements for particular types of tool which either supplement or modify the requirements given in Part 1 to account for the particular hazards and characteristics of these specific tools. Compliance with the relevant clauses of Part 1 together with this Part 2 provides one means of conforming to the specified essential health and safety requirements of the Directive. This European Standard follows the overall requirements of EN ISO 12100. For noise and vibration, this European Standard covers the requirements for their measurement, the provision of information arising from these measurements and the provision of information about the personal protective equipment required. Specific requirements for the reduction of the risk arising from noise and vibration through the design of the tool are not given as this reflects the current state of the art.
Warning: Other requirements arising from other EU Directives can be applicable to the products falling within the scope of this standard. SIST EN 61029-2-1:2013
– 5 – EN 61029-2-1:2012 This Part 2-1 is to be used in conjunction with EN 61029-1:2009. This Part 2-1 supplements or modifies the corresponding clauses of EN 61029-1, so as to convert it into the European Standard: “Safety requirements for transportable circular saw benches". Where a particular subclause of Part 1 is not mentioned in this Part 2-1, that subclause applies as far as is reasonable. Where this Part 2-1 states "addition", "modification" or "replacement", the relevant text of Part 1 is to be adapted accordingly. Clauses, subclauses, notes, tables and figures which are additional to those in Part 1 are numbered starting from 101. Clauses, subclauses, notes, tables and figures which are additional to those in IEC 61029-2-1 are prefixed “Z”. NOTE In this European Standard, the following print types are used: - requirements proper: in roman type;
- test specifications: in italic type;
- explanatory matter: in smaller roman type. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive. For the relationship with EU Directive 2006/42/EC, see informative Annex ZZ, which is an integral part of this document. Endorsement notice The text of the International Standard IEC 61029-2-1:1993 was approved by CENELEC as a European Standard with agreed common modifications. SIST EN 61029-2-1:2013
– 7 – EN 61029-2-1:2012 7 Marking and information for use This clause of Part 1 is applicable except as follows: 7.1 Addition: Circular saw benches shall be marked with – maximum and minimum saw blade diameter; – rated no-load speed; – thickness of riving knife; – maximum cutting capa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.