EN 50144-1:1998/A1:2002
(Amendment)Safety of hand-held electric motor operated tools - Part 1: General requirements
Safety of hand-held electric motor operated tools - Part 1: General requirements
Combined with AB, AC and AD to form A1 to EN 50144-1 * Superseded by EN 60745-1:2003 * Superseded by EN 50580:2012
Sicherheit handgeführter motorbetriebener Elektrowerkzeuge - Teil 1: Allgemeine Anforderungen
Sécurité des outils électroportatifs à moteur - Partie 1: Règles générales
Varnost električnih ročnih orodij - 1. del: Splošne zahteve
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 50144-1:2000/A1:2002
prva izdaja
STANDARD
september 2002
Varnost električnih ročnih orodij - 1. del: Splošne zahteve
Safety of hand-held electric motor operated tools - Part 1: General requirements
ICS 25.140.20 Referenčna številka
SIST EN 50144-1:2000/A1:2002(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 50144-1/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM January 2002
ICS 25.140.20
English version
Safety of hand-held electric motor operated tools
Part 1: General requirements
Sécurité des outils électroportatifs à Sicherheit handgeführter
moteur motorbetriebener Elektrowerkzeuge
Partie 1: Règles générales Teil 1: Allgemeine Anforderungen
This amendment A1 modifies the European Standard EN 50144-1:1998; it was approved by CENELEC
on 2001-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this amendment the status of a national standard without any
alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands,
Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 50144-1:1998/A1:2002 E
---------------------- Page: 2 ----------------------
EN 50144-1:1998/A1:2002 - 2 -
Foreword
This amendment to the European Standard EN 50144-1 was prepared by the Technical
Committee CENELEC TC 61F, Hand-held and transportable electric motor-operated tools.
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by
CENELEC as amendment A1 to EN 50144-1:1998 on 2001-05-01.
The following dates were fixed:
- latest date by which the amendment has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2002-08-01
- latest date by which the national standards conflicting
with the amendment have to be withdrawn (dow) 2004-08-01
__________
---------------------- Page: 3 ----------------------
- 3 - EN 50144-1:1998/A1:2002
2 Definitions
Add the following definitions:
2.2.35
type X attachment
method of attachment of the supply cord such that it can easily be replaced
NOTE 1 The supply cord may be specially prepared and only available from the manufacturer or its service agent.
NOTE 2 A specially prepared cord may also include a part of the tool.
2.2.36
type Y attachment
method of attachment of the supply cord such that any replacement is intended to be made by
the manufacturer, its service agent or similar qualified person
NOTE Type Y attachment may be used either with an ordinary flexible cord or with a special cord.
7 Marking and information for use
7.9 Delete the whole subclause.
7.13 Add the following subclause:
7.13.3 The instructions shall contain the substance of the following:
- for appliances with type X attachment having a specially prepared cord:
if the supply cord is damaged, it must be replaced by a special cord or assembly available
from the manufacturer or its service agent;
- for appliances with type Y attachment:
if the supply cord is damaged, it must be replaced by the manufacturer or its service agent or
a similarly qualified person in order to avoid hazard.
Compliance is checked by inspection.
11 Heating
2)
Replace in the first row of Table 2 "other material " by:
of Class H material 140
of Class 200 material 160
of Class 220 material 180
of Class 250 material 210
In footnote 1:
- under “Class B" materials, delete “asbestos”,
- under “Class F" materials, delete “and asbestos” and “, varnished asbestos”.
Delete footnote 2.
---------------------- Page: 4 ----------------------
EN 50144-1:1998/A1:2002 - 4 -
13 Environmental requirements
13.2.5 In the formula, under the summation sign, replace "j = 1" with "i = 1".
13.2.6 Read “L is the A weighted sound power level, in decibels .” (not “pressure”)
w
14 Moisture resistance
st nd rd
, 2 and 3 paragraphs by :
14.1 Replace the 1
The enclosure of splash-proof and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.