iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 60695-5-1:2003

(Main)

Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance

Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance

Provides guidance on the following: a) general aspects of corrosion damage test methods; b) methods of measurement of corrosion damage; c) consideration of test methods; d) relevance of corrosion damage data to hazard assessment. The structure of this second edition remains essentially the same as the first edition with the following additions: - Information on fire scenarios and fire models has been added along with an update on the latest advances in the analysis of the fire effluent. - The general classification of fires from ISO TR 9122-1 has been added. - A new clause on the general aspects of the corrosivity of fire effluent which describes the types of corrosion damage effects and the factors affecting corrosivity. - A new clause on the principles of corrosion damage measurement has been added describing the assessment of the corrosive potential and the consideration of the corrosivity test methods. - A new table describing a summary of corrosion test methods. - A new flowchart detailing the evaluation and consideration of corrosion damage test methods. - The bibliography has been expanded. Has the status of a basic safety publication in accordance with IEC guide 104.

Prüfungen zur Beurteilung der Brandgefahr - Teil 5-1: Korrosionsschädigung durch Rauch und/oder Brandgase - Allgemeiner Leitfaden

Essais relatifs aux risques du feu - Partie 5-1: Effets des dommages de corrosion des effluents du feu - Guide général

Fournit un guide concernant: a) les aspects généraux des méthodes d'essai des dommages provoqués par la corrosion; b) les méthodes de mesure des dommages provoqués par la corrosion; c) la prise en compte des méthodes d'essai; d) la pertinence des données concernant les dommages de corrosion pour l'évaluation des risques. La structure de la deuxième édition demeure pratiquement inchangée, à l'exception des éléments importants suivants qui ont été ajoutés: - Information relative aux scénarios et aux modèles de feu ainsi qu'une mise à jour des dernières avancées réalisées dans l'analyse des effluents du feu. - Classification générale des feux selon l'ISO TR 9122-1. - Nouvel article relatif aux aspects généraux de la corrosivité des effluents du feu, décrivant les types d'effets des dommages de la corrosion et les facteurs affectant la corrosivité. - Nouvel article relatif aux principes de mesure des dommages de la corrosion, décrivant l'évolution du potentiel corrosif et la prise en compte des méthodes d'essai de la corrosivité. - Nouveau tableau résumant les méthodes d'essai de la corrosivité. - Nouvel organigramme présentant en détail l'évaluation et la prise en compte des méthodes d'essai des dommages de la corrosion. - Elargissement de la bibliographie. A le statut d'une publication fondamentale de sécurité conformément au Guide 104 de la CEI.

Preskušanje požarne ogroženosti - 5-1. del: Poškodbe zaradi korozijskega učinka izžarevanja ognja - Splošno navodilo

General Information

Status
Published
Publication Date
13-Feb-2003
Withdrawal Date
31-Jan-2006
ICS
29.020 - Electrical engineering in general
Technical Committee
CLC/SR 89 - Fire hazard testing
Drafting Committee
IEC/TC 89 - IEC_TC_89
Parallel Committee
IEC/TC 89 - IEC_TC_89
Current Stage
6060 - Document made available - Publishing
Start Date
14-Feb-2003
Completion Date
14-Feb-2003
Ref Project
SIST EN 60695-5-1:2003 - Fire hazard testing -- Part 5-1: Corrosion damage effects of fire effluent - General guidance

Relations

Replaces
EN 60695-5-1:1993 - Fire hazard testing - Part 5: Assessment of potential corrosion damage by fire effluent - Section 1: General guidance
Effective Date
28-Jan-2023
Replaced By
EN IEC 60695-5-1:2021 - Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance
Effective Date
23-Jan-2023

Buy Standard

EN 60695-5-1:2003EN 60695-5-1:2003
PreviousNext
Standard
EN 60695-5-1:2003
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60695-5-1:2003
01-julij-2003
1DGRPHãþD
SIST EN 60695-5-1:2001
3UHVNXãDQMHSRåDUQHRJURåHQRVWLGHO3RãNRGEH]DUDGLNRUR]LMVNHJDXþLQND
L]åDUHYDQMDRJQMD6SORãQRQDYRGLOR
Fire hazard testing -- Part 5-1: Corrosion damage effects of fire effluent - General
guidance
Prüfungen zur Beurteilung der Brandgefahr -- Teil 5-1: Korrosionsschädigung durch
Rauch und/oder Brandgase - Allgemeiner Leitfaden
Essais relatifs aux risques du feu -- Partie 5-1: Effets des dommages de corrosion des
effluents du feu - Guide général
Ta slovenski standard je istoveten z: EN 60695-5-1:2003
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
SIST EN 60695-5-1:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60695-5-1:2003

---------------------- Page: 2 ----------------------

SIST EN 60695-5-1:2003
EUROPEAN STANDARD EN 60695-5-1
NORME EUROPÉENNE
EUROPÄISCHE NORM February 2003

ICS 29.020 Supersedes EN 60695-5-1:1993


English version


Fire hazard testing
Part 5-1: Corrosion damage effects of fire effluent -
General guidance
(IEC 60695-5-1:2002)


Essais relatifs aux risques du feu Prüfungen zur Beurteilung
Partie 5-1: Effets des dommages der Brandgefahr
de corrosion des effluents du feu - Teil 5-1: Korrosionsschädigung
Guide général durch Rauch und/oder Brandgase -
(CEI 60695-5-1:2002) Allgemeiner Leitfaden
(IEC 60695-5-1:2002)





This European Standard was approved by CENELEC on 2003-02-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta,
Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60695-5-1:2003 E

---------------------- Page: 3 ----------------------

SIST EN 60695-5-1:2003
EN 60695-5-1:2003 - 2 -
Foreword

The text of document 89/556/FDIS, future edition 2 of IEC 60695-5-1, prepared by IEC TC 89, Fire
hazard testing, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60695-5-1 on 2003-02-01.

This European Standard supersedes EN 60695-5-1:1993

The following dates were fixed:

– latest date by which the EN has to be implemented
 at national level by publication of an identical
 national standard or by endorsement (dop) 2003-11-01

– latest date by which the national standards conflicting
 with the EN have to be withdrawn (dow) 2006-02-01

This European Standard should be read in conjunction with IEC 60695-5-2 and IEC 60695-5-3.

Annexes designated "normative" are part of the body of the standard.
In this standard, annex ZA is normative.
Annex ZA has been added by CENELEC.
__________

Endorsement notice

The text of the International Standard IEC 60695-5-1:2002 was approved by CENELEC as a
European Standard without any modification.

In the official version, for Bibliography, the following note has to be added for the standard indicated:

ISO 7384 NOTE Harmonized as EN ISO 7384:1995 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60695-5-1:2003
- 3 - EN 60695-5-1:2003
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of any
of these publications apply to this European Standard o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN IEC 60695-2-10:2021/AC:2024-01(Corrigendum)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
SIST EN IEC 60695-2-10:2022/AC:2024
  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-7-2:2021(Main)
Fire hazard testing - Part 7-2: Toxicity of fire effluent - Summary and relevance of test methods
SIST EN IEC 60695-7-2:2022

IEC 60695-7-2:2021 gives a brief summary of the test methods that are in common use in the assessment of the toxicity of fire effluent. It includes special observations on their relevance to real fire scenarios and gives recommendations on their use. It advises which tests provide toxic potency data that are relevant to real fire scenarios, and which are suitable for use in fire hazard assessment and fire safety engineering. The list of test methods is not to be considered exhaustive. This summary cannot be used in place of published standards which are the only valid reference documents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This second edition cancels and replaces the first edition published in 2011. This edition constitutes a technical revision. The main changes with respect to the previous edition are listed below: – New text in the introduction; – New text in the scope; – Clause 2 has been updated; – Many terms and definitions in Clause 3 reproduced from ISO 13943 have been deleted. Other terms and definitions have been added. – New text in Subclauses 4.3 and 4.4; – New text in Subclause 6.1; – References to IEC 60695-7-50 and -51 (now withdrawn) have been removed; – Reference to DEF STAN 07-247 has been added; – Details of ISO/TS 19021 have been added; – Details of EN 17084 have been added; – New text added concerning ISO/TS 19700; – New text added concerning the IMO FTP toxicity test; – New Subclause 7.1 has been added; – The Annex in Edition1 has been replaced by new Clause 8; – The bibliography has been updated.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-5-1:2021(Main)
Fire hazard testing - Part 5-1: Corrosion damage effects of fire effluent - General guidance
SIST EN IEC 60695-5-1:2022

This part of IEC 60695 provides guidance on the following: a) general aspects of corrosion damage test methods; b) methods of measurement of corrosion damage; c) consideration of test methods; d) relevance of corrosion damage data to hazard assessment. This basic safety publication is primarily intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. It is not intended for use by manufacturers or certification bodies. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-11:2021(Main)
Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end products (GWEPT)
SIST EN IEC 60695-2-11:2022

This part of IEC 60695 specifies a test method on an end product. It is intended to simulate the effects of thermal stresses produced by an electrically heated source to represent a fire hazard. This test method is used to check that, under defined test conditions, an end product exposed to an electrically heated source has either a limited ability to ignite or, if it ignites, a limited ability to propagate flame. However, the fire hazard analysis, the flammability aspects and the flame spreading to other products are not covered by this document. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-10:2021(Main)
Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure
SIST EN IEC 60695-2-10:2022

This part of IEC 60695 specifies the glow-wire apparatus and common test procedure to simulate the effects of thermal stresses which may be produced by heat sources such as glowing elements or overloaded resistors, for short periods, in order to assess the fire hazard by a simulation technique. The test procedure described in this document is a common test procedure intended for the small-scale tests in which a standardized electrically heated wire is used as a source of ignition. It is a common part of the test procedures applied to end products and to solid electrical insulating materials or other solid combustible materials. A detailed description of each particular test procedure is given in IEC 60695-2-11, IEC 60695-2-12 and IEC 60695-2-13. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-12:2021(Main)
Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials
SIST EN IEC 60695-2-12:2022

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for flammability testing to determine the glow-wire flammability index (GWFI). GWFI is the highest temperature, determined during this standardized procedure, at which the tested material does not ignite or, if it does, extinguishes within 30 s after removal of the glow-wire and is not totally consumed; and molten drips, if they occur, do not ignite the wrapping tissue. This test method is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire ignition temperature (GWIT) test method for materials, IEC 60695-2-13, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests can allow a reduction of end product testing. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-9-2:2021(Main)
Fire hazard testing - Part 9-2: Surface spread of flame - Summary and relevance of test methods
SIST EN IEC 60695-9-2:2021

IEC 60695-9-2:2021 presents a summary of published test methods that are used to determine the surface spread of flame of electrotechnical products or materials from which they are formed. It represents the current state of the art of the test methods and, where available, includes special observations on their relevance and use. The list of test methods is not to be considered exhaustive, and test methods that were not developed by the IEC are not to be considered as endorsed by the IEC unless this is specifically stated. This summary cannot be used in place of published standards which are the only valid reference documents. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This International Standard is to be used in conjunction with IEC 60695-1. This second edition cancels and replaces the first edition of IEC 60695-9-2 published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) Updated introduction b) Updated normative references c) Updated terms and definitions d) New Subclauses 4.1 and 4.2 e) Reference to fire stages as defined in ISO 19706 (Table 1) f) New sub-division of tests into the following subclauses: 4.3 Small-scale fire tests 4.4 Medium and intermediate-scale fire tests 4.5 Intermediate and large-scale fire tests for cables 4.6 Real-scale fire tests for cables g) Updated text in parts of Clause 4 h) Addition of the following test methods: IEC TS 60695-11-21 IEC 60684-2:2011, Clause 26 ISO 3582 ISO 9772 ISO 9773 ISO 12992 ISO 21367 i) New Clause 5 and Table 4 giving an overview of test methods j) Deletion of all the Annexes k) Updated bibliography

  • Standard
    44 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-2-13:2021(Main)
Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials
SIST EN IEC 60695-2-13:2021

This part of IEC 60695 specifies the details of the glow-wire test to be applied to test specimens of solid electrical insulating materials or other solid materials for ignitability testing to determine the glow-wire ignition temperature (GWIT). The GWIT is the temperature which is 25 K (or 30 K) higher than the maximum test temperature, determined during this standardized procedure, at which the tested material does not ignite, or sustained flaming combustion does not occur for a time longer than 5 s for any single flame event and the specimen is not totally consumed. This test is a materials test carried out on a series of standard test specimens. The data obtained, along with data from the glow-wire flammability index (GWFI) test method for materials, IEC 60695-2-12, can then be used in a preselection process in accordance with IEC 60695-1-30 [4] to judge the ability of materials to meet the requirements of IEC 60695-2-11. NOTE As an outcome of conducting a fire hazard assessment, an appropriate series of preselection flammability and ignition tests can allow a reduction of end product testing. This basic safety publication focusing on safety test method(s) is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-6-1:2021(Main)
Fire hazard testing - Part 6-1: Smoke obscuration - General guidance
SIST EN IEC 60695-6-1:2021

IEC 60695-6-1:2021 is available as IEC 60695-6-1:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60695-6-1:2021 gives guidance on: a) the optical measurement of obscuration of smoke; b) general aspects of optical smoke test methods; c) consideration of test methods; d) expression of smoke test data; e) the relevance of optical smoke data to hazard assessment. This basic safety publication focusing on safety guidance is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. This third edition cancels and replaces the second edition of IEC 60695-6-1 published in 2005 and Amendment 1:2010. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: - References to IEC TS 60695-6-30 (withdrawn in 2016) have been removed. - References to IEC TS 60695-6-31 (withdrawn in 2016) have been removed. - References to ISO 5659-2 have been inserted. - The scope contains some additional text. - Terms and definitions have been updated. - Subclause 3.2 has been updated. - Subclause 7.1 has been updated. It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51. This International Standard is to be used in conjunction with IEC 60695-6-2.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN IEC 60695-4:2021(Main)
Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products
SIST EN IEC 60695-4:2021

IEC 60695-4:2021 is available as IEC 60695-4:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 60695-4:2021 The terms and definitions in this part of IEC 60695 are applicable to fire tests for electrotechnical products. This basic safety publication focusing on safety guidance is primarily intended for use by technical committees in the preparation of safety publications in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications. This fifth edition cancels and replaces the fourth edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) The terms and definitions that are not specifically electrotechnical and that are either identical or equivalent to those in ISO 13943:2017 have been deleted. b) The terms and definitions that are specifically electrotechnical and that are in ISO 13943:2017 have been included for the convenience of the user. It has the status of a basic safety publication in accordance with IEC Guide 104 and ISO/IEC Guide 51.

  • Standard
    11 pages
    English language
    sale 10% off
    e-Library read for
    1 day