EN 60239:2005
(Main)Graphite electrodes for electric arc furnaces - Dimensions and designation
Graphite electrodes for electric arc furnaces - Dimensions and designation
Specifies the dimensions of turned and threaded cylindrical graphite arc furnace electrodes and graphite electrode pins for use as full graphite electrode columns on arc furnaces. Is essential for the interchangeability of electrodes from different sources.
Graphitelektroden für Lichtbogenöfen - Maße und Kennzeichnung
Electrodes en graphite pour les fours à arc - Dimensions et dénomination
Spécifie les dimensions des électrodes en graphite cylindriques tournées avec logements filetés pour les fours à arc et des raccords des électrodes en graphite employés sur les fours à arc sous la forme de colonnes d'électrodes en graphite. Est essentielle pour assurer l'interchangeabilité entre électrodes d'origines différentes.
Grafitne elektrode za električne obločne peči - Mere in označbe (IEC 60239:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI SIST EN 60239:2005
STANDARD
december 2005
Grafitne elektrode za električne obločne peči – Mere in označbe (IEC
60239:2005)
Graphite electrodes for electric arc furnaces – Dimensions and designation (IEC
60239:2005)
ICS 25.180.10 Referenčna številka
SIST EN 60239:2005(en)
© Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD EN 60239
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2005
ICS 25.180.10 Supersedes EN 60239:1997
English version
Graphite electrodes for electric arc furnaces –
Dimensions and designation
(IEC 60239:2005)
Electrodes en graphite pour les fours Graphitelektroden für Lichtbogenöfen -
à arc – Maße und Kennzeichnung
Dimensions et dénomination (IEC 60239:2005)
(CEI 60239:2005)
This European Standard was approved by CENELEC on 2005-07-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60239:2005 E
---------------------- Page: 2 ----------------------
EN 60239:2005 - 2 -
Foreword
The text of document 27/464/FDIS, future edition 4 of IEC 60239, prepared by IEC TC 27, Industrial
electroheating equipment, was submitted to the IEC-CENELEC parallel vote and was approved by
CENELEC as EN 60239 on 2005-07-01.
This European Standard supersedes EN 60239:1997.
Significant technical changes with respect to EN 60239:1997 are as follows:
– addition of 750 mm nominal diameter electrodes;
– revision of electrode diameter and length tolerances;
– revision of nominal lengths and diameters;
– introduction of socket and pin tolerances;
– revision of Annex A on male-female electrodes;
– addition of Annex B on handling and jointing.
This new edition also aims at a better compatibility between EN 60239 and other technical standards
that cover the same subject, as well as better compliance with standards for figures, tables and
symbols – in that respect, and in addition to the content, the format and the title of this standard have
been modified.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-04-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-07-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60239:2005 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 3 ----------------------
- 3 - EN 60239:2005
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60050-841 2004 International electrotechnical vocabulary - -
Part 841: Industrial electroheat
---------------------- Page: 4 ----------------------
NORME CEI
INTERNATIONALE
IEC
60239
INTERNATIONAL
Quatrième édition
STANDARD
Fourth edition
2005-06
Electrodes en graphite pour les fours à arc –
Dimensions et dénomination
Graphite electrodes for electric arc furnaces
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.