Magnetic materials - Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip

Defines a measurement method for the determination of the characteristics of surface insulation resistance of magnetic sheet and strip. Applicable to magnetic sheet and strip insulated on one or both surfaces and is suitable for manufacturing control in the application of insulation coatings. This consolidated version consists of the first edition (1991) and its amendment 1 (1998). Therefore, no need to order amendment in addition to this publication.

Matériaux magnétiques - Partie 11: Méthode d'essai pour la détermination de la résistance d'isolement superficiel des tôles et feuillards magnétiques

Définit une méthode de mesure pour la détermination des caractéristiques de résistance d'isolement superficiel des tôles et feuillards magnétiques. S'applique aux tôles ou feuillards magnétiques isolés sur une ou deux faces et est adaptée au contrôle de fabrication dans le cas d'application de revêtements isolants.  Cette version consolidée comprend la première édition (1991) et son amendement 1 (1998). Il n'est donc pas nécessaire de commander l'amendement avec cette publication.

General Information

Status
Published
Publication Date
20-Jan-1999
Current Stage
DELPUB - Deleted Publication
Completion Date
08-Jul-2021
Ref Project

Buy Standard

Standard
IEC 60404-11:1991+AMD1:1998 CSV - Magnetic materials - Part 11: Method of test for the determination of surface insulation resistance of magnetic sheet and strip
English and French language
17 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

IEC 60404-11
Edition 1.1 1999-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic materials –
Part 11: Method of test for the determination of surface insulation resistance of
magnetic sheet and strip

Matériaux magnétiques –
Partie 11: Méthode d'essai pour la détermination de la résistance d'isolement
superficiel des tôles et feuillards magnétiques
IEC 60404-11:1991+A1:1998

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 1999 IEC, Geneva, Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by
any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or
IEC's member National Committee in the country of the requester.
If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication,
please contact the address below or your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite
ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie
et les microfilms, sans l'accord écrit de la CEI ou du Comité national de la CEI du pays du demandeur.
Si vous avez des questions sur le copyright de la CEI ou si vous désirez obtenir des droits supplémentaires sur cette
publication, utilisez les coordonnées ci-après ou contactez le Comité national de la CEI de votre pays de résidence.

IEC Central Office
3, rue de Varembé
CH-1211 Geneva 20
Switzerland
Email: inmail@iec.ch
Web: www.iec.ch

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
ƒ Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
ƒ IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
ƒ Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
ƒ Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
Fax: +41 22 919 03 00


A propos de la CEI
La Commission Electrotechnique Internationale (CEI) est la première organisation mondiale qui élabore et publie des
normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications CEI
Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possédez
l’édition la plus récente, un corrigendum ou amendement peut avoir été publié.
ƒ Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm
Le Catalogue en-ligne de la CEI vous permet d’effectuer des recherches en utilisant différents critères (numéro de référence,
texte, comité d’études,…). Il donne aussi des informations sur les projets et les publications retirées ou remplacées.
ƒ Just Published CEI: www.iec.ch/online_news/justpub
Restez informé sur les nouvelles publications de la CEI. Just Published détaille deux fois par mois les nouvelles
publications parues. Disponible en-ligne et aussi par email.
ƒ Electropedia: www.electropedia.org
Le premier dictionnaire en ligne au monde de termes électroniques et électriques. Il contient plus de 20 000 termes et
définitions en anglais et en français, ainsi que les termes équivalents dans les langues additionnelles. Egalement appelé
Vocabulaire Electrotechnique International en ligne.
ƒ Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm
Si vous désirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du
Service clients ou contactez-nous:
Email: csc@iec.ch
Tél.: +41 22 919 02 11
Fax: +41 22 919 03 00

---------------------- Page: 2 ----------------------
IEC 60404-11
Edition 1.1 1999-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Magnetic materials –
Part 11: Method of test for the determination of surface insulation resistance of
magnetic sheet and strip

Matériaux magnétiques –
Partie 11: Méthode d'essai pour la détermination de la résistance d'isolement
superficiel des tôles et feuillards magnétiques

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CB
CODE PRIX
ICS 17.220.01; 29.030 ISBN 2-8318-4599-8

---------------------- Page: 3 ----------------------
– 2 – 60404-11 © CEI:1991+A.1:1998
SOMMAIRE
Pages
AVANT-PROPOS . 4
Articles
1 Objet et domaine d'application. 6
2 Principe de mesure . 6
3 Eprouvette . 8
4 Appareillage. 8
4.1 Ensemble des contacts . 8
4.2 Source de courant. 10
4.3 Mesurage du courant . 10
4.4 Détermination de la force appliquée . 12
5 Calibrage . 12
6 Mode opératoire . 14
7 Evaluation de la résistance d'isolement superficiel. 14
8 Rapport d'essai . 16

---------------------- Page: 4 ----------------------
60404-11 © IEC:1991+A.1:1998 – 3 –
CONTENTS
Page
FOREWORD . 5
Clause
1 Scope and field of application. 7
2 Principle of measurement. 7
3 Test specimen.9
4 Apparatus . 9
4.1 Contact assembly. 9
4.2 Power supply . 11
4.3 Current measurement . 11
4.4 Determination of applied force. 13
5 Calibration . 13
6 Measuring procedure. 15
7 Evaluation of surface insulation resistance . 15
8 Test report . 17

---------------------- Page: 5 ----------------------
– 4 – 60404-11 © CEI:1991+A.1:1998
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
–––––––––––––
MATÉRIAUX MAGNÉTIQUES –
Partie 11: Méthode d'essai pour la détermination
de la résistance d'isolement superficiel
des tôles et feuillards magnétiques

AVANT-PROPOS
1) La CEI (Commission Electrotechnique Internationale) est une organisation mondiale de normalisation composée
de l'ensemble des comités électrotechniques nationaux (Comités nationaux de la CEI). La CEI a pour objet de
favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines de
l'électricité et de l'électronique. A cet effet, la CEI, entre autres activités, publie des Normes internationales.
Leur élaboration est confiée à des comités d'études, aux travaux desquels tout Comité national intéressé par le
sujet traité peut participer. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec la CEI, participent également aux travaux. La CEI collabore étroitement avec l'Organisation
Internationale de Normalisation (ISO), selon des conditions fixées par accord entre les deux organisations.
2) Les décisions ou accords officiels de la CEI concernant les questions techniques représentent, dans la mesure
du possible un accord international sur les sujets étudiés, étant donné que les Comités nationaux intéressés
sont représentés dans chaque comité d’études.
3) Les documents produits se présentent sous la forme de recommandations internationales. Ils sont publiés
comme normes, rapports techniques ou guides et agréés comme tels par les Comités nationaux.
4) Dans le but d'encourager l'unification internationale, les Comités nationaux de la CEI s'engagent à appliquer de
façon transparente, dans toute la mesure possible, les Normes internationales de la CEI dans leurs normes
nationales et régionales. Toute divergence entre la norme de la CEI et la norme nationale ou régionale
correspondante doit être indiquée en termes clairs dans cette dernière.
5) La CEI n’a fixé aucune procédure concernant le marquage comme indication d’approbation et sa responsabilité
n’est pas engagée quand un matériel est déclaré conforme à l’une de ses normes.
6) L’attention est attirée sur le fait que certains des éléments de la présente Norme internationale peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. La CEI ne saurait être tenue pour
responsable de ne pas avoir identifié de tels droits de propriété et de ne pas avoir signalé leur existence.

La présente Norme internationale a été établie par le comité d'études 68 de la CEI: Matériaux
magnétiques tels qu'alliages et aciers.
La présente version consolidée de la CEI 60404-11 comprend la première édition (1991)
[documents 68(BC)69 et 68(BC)76] et son amendement 1 (1998) [documents 68/181/FDIS et
68/186/RVD].
Le contenu technique de cette version consolidée est donc identique à celui de l'édition de
base et à son amendement; cette version a été préparée par commodité pour l'utilisateur.
Elle porte le numéro d'édition 1.1.
Une ligne verticale dans la marge indique où la publication de base a été modifiée par
l'amendement 1.

---------------------- Page: 6 ----------------------
60404-11 © IEC:1991+A.1:1998 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
–––––––––––
MAGNETIC MATERIALS –
Part 11: Method of test for the determination
of surface insulation resistance of
magnetic sheet and strip

FOREWORD
1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, the IEC publishes International Standards. Their preparation is
entrusted to technical committees; any IEC National Committee interested in the subject dealt with may
participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization
for Standardization (ISO) in accordance with conditions determined by agreement between the two
organizations.
2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has representation
from all interested National Committees.
3) The documents produced have the form of recommendations for international use and are published in the form
of standards, technical reports or guides and they are accepted by the National Committees in that sense.
4) In order to promote international unification, IEC National Committees undertake to apply IEC International
Standards transparently to the maximum extent possible in their national and regional standards. Any
divergence between the IEC Standard and the corresponding national or regional standard shall be clearly
indicated in the latter.
5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with one of its standards.
6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject
of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.

This International Standard has been prepared by IEC technical committee 68: Magnetic alloys
and steels.
This consolidated version of IEC 60404-11 consists of the first edition (1991) [documents
68(CO)69 and 68(CO)76] and its amendment 1 (1998) [documents 68/181/FDIS and 68/186/RVD].
The technical content is therefore identical to the base edition and its amendment and has
been prepared for user convenience.
It bears the edition number 1.1.
A vertical line in the margin shows where the base publication has been modified by
amendment 1.

---------------------- Page: 7 ----------------------
– 6 – 60404-11 © CEI:1991+A.1:1998
MATÉRIAUX MAGNÉTIQUES –
Partie 11: Méthode d'essai pour la détermination
de la résistance d'isolement superficiel des
tôles et feuillards magnétiques
1 Objet et domaine d'application
La présente Norme internationale a pour objet de définir une méthode de mesure pour la
détermination des caractéristiques de résistance d'isolement superficiel des tôles et feuillards
magnétiques.
Cette méthode est applicable aux tôles ou feuillards magnétiques isolés sur une ou deux faces
et est adaptée au contrôle de fabrication dans le cas d'application de revêtements isolants.
2 Principe de mesure
*
Le principe de mesure s'appuie sur, et inclut, la méthode décrite à l'origine par Franklin qui
permet de caractériser une seule face revêtue à la fois.
L'organisation de l'appareillage est décrite par la figure 1. Dix contacts métalliques de surfaces
déterminées sont appliqués sur une seule face revêtue de la tôle, sous des conditions définies
de tension électrique et de pression.
L'efficacité de l'isolation superficielle est évaluée par la mesure des courants traversant les 10
contacts.
Source
Micro-
d'alimentation
processeur
Affichage
Touches de contact
Foret hélicoïdal
(10 au total)
pour contact
Revêtement
isolant
Eprouvette
IEC  1 595/98
Figure 1 – Organisation de l'appareillage pour la mesure
de la résistance d'isolement superficiel
–––––––––
*
Franklin, R.F., «Measurement and control of interlaminar resistance of laminated magnetic cores», ASTM
Bulletin, n° 144, janvier 1947, p. 57.

---------------------- Page: 8 ----------------------
60404-11 © IEC:1991+A.1:1998 – 7 –
MAGNETIC MATERIALS –
Part 11: Method of test for the determination
of surface insulation resistance of
magnetic sheet and strip
1 Scope and field of application
This International Standard is intended to define a measurement method for the determination
of the characteristics of surface insulation resistance of magnetic sheet and strip.
This method is applicable to magnetic sheet and strip insulated on one or both surfaces and is
suitable for manufacturing control in the application of insulation coatings.
2 Principle of measurement
The principle of the measurement is based on, and includes, the method originally described by
*
Franklin which characterizes only one coated surface at a time.
The arrangement of the apparatus is shown in figure 1. Ten metallic contacts of fixed area are
applied to one coated surface of the sheet, under specified conditions of voltage and pressure.
The effectiveness of the surface insulation is assessed by the measurement of the currents
through the 10 contacts.
Micro-
Power supply
processor
Display
Contact buttons
Twist drill
(a total of 10)
for contact
Insulation
coating
Test specimen
IEC  1 595/98
Figure 1 – Arrangement of apparatus for the measurement of
surface insulation resistance
–––––––––
*
Franklin, R.F., "Measurement and control of interlaminar resistance of laminated magnetic cores", ASTM
Bulletin, no. 144, January 1947, p. 57.

---------------------- Page: 9 ----------------------
– 8 – 60404-11 © CEI:1991+A.1:1998
Chaque touche de contact est alimentée individuellement par une source de courant continu
selon une des deux manières constituant les deux modes de mesure en vigueur dans cette
norme, à savoir:
a) Mode A La tension électrique entre l'extrémité des résistances de 5 Ω ± 1 % (voir figure 2)
connectées à la source et les forets de contact est stabilisée à 500 mV ± 0,5 % pour une
plage de courant allant de 0 à 1 A. Les deux forets hélicoïdaux assurent la fonction de
contact avec le substrat pour le passage du courant.
b) Mode B La tension électrique entre chaque touche de contact et les forets de contact est
stabilisée à 250 mV ± 0,5 % pour une plage de courant allant de 0 à 2,5 A en vue de
l'analyse des courants d'électrodes individuels. Les deux forets hélicoïdaux assurent des
fonctions différentes. Un foret fournit le contact avec le substrat pour le passage du
couran
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.