IEC 62026-3:2014/COR2:2019
(Corrigendum)Corrigendum 2 - Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet
Corrigendum 2 - Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 3: DeviceNet
Corrigendum 2 - Appareillage à basse tension - Interfaces appareil de commande-appareil (CDI) - Partie 3: DeviceNet
General Information
Relations
Standards Content (Sample)
IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
IEC 62026-3 IEC 62026-3
Edition 3.0 2014-08 Édition 3.0 2014-08
Low-voltage switchgear and controlgear – Appareillage à basse tension – Interfaces
Controller-device interfaces (CDIs) – appareil de commande-appareil (CDI) –
Part 3: DeviceNet Partie 3: DeviceNet
CO RRI G E NDUM 2
Corrections to the French version appear after the English text.
Les corrections à la version française sont données après le texte anglais.
Figure 44 – Success response to release_master/slave_connection_set request
This correction appli
...
This May Also Interest You
- Standard54 pagesEnglish and French languagesale 15% off
IEC 60947-3:2020 applies to switches, disconnectors, switch-disconnectors and fuse-combination units and their dedicated accessories to be used in distribution circuits and motor circuits of which the rated voltage does not exceed 1 000 V AC or 1 500 V DC. This fourth edition cancels and replaces the third edition published in 2008, Amendment 1:2012 and Amendment 2:2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- addition of critical load current tests for DC switches (see 9.3.9);
- addition of requirements for a conditional short-circuit rating for disconnectors, switches, and switch-disconnectors protected by circuit-breakers (see 9.3.7.2);
- addition of new categories for high-efficiency motors switching (see Annex A);
- addition of new Annex E for connection to aluminium conductors;
- addition of new Annex F for power losses measurement.
The contents of the corrigendum of October 2021 have been included in this copy.
- Standard217 pagesEnglish languagesale 15% off
- Standard190 pagesEnglish and French languagesale 15% off
IEC 60947-7-1:2025 specifies requirements for terminal blocks and test disconnect terminal blocks according to Annex D with screw-type or screw-less-type clamping units primarily intended for industrial or similar use and to be fixed to a support to provide electrical and mechanical connection between copper conductors. It applies to terminal blocks intended to connect round copper conductors, with or without special preparation, having a cross-section between 0,05 mm2/30 AWG and 300 mm2/600 kcmil, intended to be used in circuits of a rated voltage not exceeding 1 000 V AC up to 1 000 Hz or 1 500 V DC. The tests on terminal blocks are made with AC or DC supply as required in relevant clauses of this document.
This fourth edition cancels and replaces the third edition published in 2009. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Scope extension for smaller conductor cross-sections;
b) Implementation of a contact pressure via insulation material (CoPI) test;
c) Introduction of new informative Annex E for larger cross-sections;
d) Reorganisation of all tables merged into two tables for electrical and mechanical values;
e) Implementation of AWG-sizes conductor types as an equivalent type of metric conductor with examples in Annex C;
f) Reorganisation of Annex D test disconnect terminal blocks to enhance readability;
g) Introduction of new informative Annex A for main characteristics of terminal blocks.
- Standard99 pagesEnglish and French languagesale 15% off
- Standard32 pagesEnglish and French languagesale 15% off
IEC 60947-4-2:2020 applies to semiconductor motor controllers, starters and soft-starters which can include a series mechanical switching device, intended to be connected to circuits the rated voltage of which does not exceed 1 000 V AC.
This fourth edition cancels and replaces the third edition published in 2011. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- scope exclusions;
- editorial correction of notes and hanging paragraphs;
- reference to IEC 62683-1;
- safety aspects related to:
- general aspects;
- limited energy circuits;
- electronic circuits;
- mention of dedicated wiring accessories;
- power consumption measurement;
- alignment to IEC 60947-1:2020.
- Standard228 pagesEnglish languagesale 15% off
- Standard230 pagesEnglish and French languagesale 15% off
IEC 60947-2:2024 applies to circuit-breakers, intended to be installed and operated by instructed or skilled persons, the main contacts of which are intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC; it also contains additional requirements for integrally fused circuit-breakers.
This document also applies to circuit-breakers with ratings at or below 1 000 V AC, additionally having one or more ratings above 1 000 V AC but not exceeding 1 500 V AC.
This sixth edition cancels and replaces the fifth edition published in 2016 and its Amendment 1: 2019. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) suitability for isolation (see Clause 1);
b) removal of the classification according to the interrupting medium, according to the design, according to the suitability for isolation (see Clause 4);
c) adjustment of current settings with an external device connectable to the release (see 5.7.3);
d) requirements for circuits with protective separation (see 8.2.3.8);
e) additional tests for ground-fault overcurrent releases (see 9.3.4.2.5);
f) additional tests concerning dielectric properties in tripped position (see 9.3.4.3);
g) use of DC voltage for dielectric tests (see 9.3.4.6.2 and 9.4.6);
h) tests of individual pole breaking capacity under phase-to-neutral AC voltage (see 9.3.11);
i) improvement of measurement of power loss in Annex G;
j) changes in EMC tests (see Annex J);
k) introduction of CBI class W in Annex L.
- Standard565 pagesEnglish and French languagesale 15% off
IEC 60947-1:2020 applies, when required by the relevant product standard, to low-voltage switchgear and controlgear hereinafter referred to as "equipment" or “device” and intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC.
This document states the general rules and common safety requirements for low-voltage switchgear and controlgear, including:
- definitions;
- characteristics;
- information supplied with the equipment;
- normal service, mounting and transport conditions, decommissioning and dismantling;
- constructional and performance requirements;
- verification of characteristics and performance;
- energy efficiency aspects (see Annex V);
- environmental aspects.
This sixth edition cancels and replaces the fifth edition published in 2007, Amendment 1:2010 and Amendment 2:2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
– DC values testing improvement;
– update of EMC tests;
– Annex B deletion;
– update of requirements for environmental tests (Table Q.1);
– improvement of Annex R (new examples);
– deletion of digital input Type 2, and introduction of Type 3 in Annex S;
– example for materials declaration (Annex W);
– new Annex X (co-ordination between short-circuit protective devices associated in the same circuit) created.
The contents of the corrigendum of December 2022 have been included in this copy.
- Standard3 pagesEnglish and French languagesale 15% off
IEC 60947-5-7:2024 states the requirements for proximity devices that correspond to the scope of IEC 60947-5-2:2019 with analog output (PDAO) and/or a digital output to transmit a corresponding digital value representing the detected sensing input. These devices can provide additional parameters.
This second edition cancels and replaces the first edition published in 2003. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) New structure;
b) Update and expansion of definitions on analog output properties;
c) Expanded performance requirements on analog output;
d) Update and new normative references;
e) Update of EMC requirements;
f) Harmonization with IEC 62828 series;
g) Harmonization with IEC 62683 and IEC 61987 definitions;
h) Harmonization with IEC 61131-2 requirements;
i) Update of the Annex A (former Annex G), Example of the determination of the conformity;
j) New Annex B, Overview tests and influence quantities;
k) New Annex C, Additional requirements for proximity switches with analog output incorporating a built-in communication interface complying with IEC 61131-9;
l) New Annex D, Main characteristics for proximity devices with analog output.
- Standard96 pagesEnglish and French languagesale 15% off
IEC 60947-5-1:2024 applies to control circuit devices and switching elements intended for controlling, signalling, interlocking, etc., of switchgear and controlgear.
It applies to control circuit devices having a rated voltage not exceeding 1 000 V AC (at a frequency not exceeding 1 000 Hz) or 600 V DC.
This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) update of the scope structure and exclusions;
b) requirements for control circuits;
c) update of the normal service conditions (e.g. shock and vibration);
d) update of information and marking requirements including environmental information requirements referencing IEC TS 63058:2021;
e) update of the constructional requirements and the corresponding tests considering safety aspects (e.g. artificial optical radiation, security aspects, limited energy source, stored charge energy circuit);
f) update of the EMC requirements according to the generic documents;
g) new requirements for reed contact magnetic switches in Annex D;
h) requirements for class II circuit devices achieved by double or reinforced insulation in Annex F;
i) update of pull-out tests in Annex G;
j) information requirements for audible signalling device in Annex J;
k) insertion of new Annex O.
- Standard263 pagesEnglish and French languagesale 15% off
IEC 60947-4-1:2023 is applicable to the following equipment:
- electromechanical contactors and starters including motor protective switching devices (MPSD and IMPSD);
- actuators of contactor relays;
- contacts dedicated exclusively to the coil circuit of the contactor or the contactor relay;
- dedicated accessories (e.g. dedicated wiring, dedicated latch accessory);
intended to be connected to distribution circuits, motors circuits and other load circuits, the rated voltage of which does not exceed 1 000 V AC or 1 500 V DC.
This fifth edition cancels and replaces the fourth edition published in 2018. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) objective in the scope;
b) instantaneous only motor protective switching device IMPSD (3.5.33);
c) kinds of equipment (5.2.1);
d) methods of overload protection of motors (5.2.6);
e) adoption of the AC-7d from IEC 61095:2023 (in 5.4.2);
f) separately mounted overload relay of a starter (in 5.7.3 b));
g) starter and contactor suitable for use downstream to basic drive module (6.1.2 w));
h) reference to IEC TS 63058 for environmental aspects (in 6.4);
i) wiring subject to movement (in 8.1.3);
j) use of voltage transient limiting device (8.1.18);
k) accessible parts subject to temperature limits (in 8.2.2.3);
l) reference to Annex X of IEC 60947-1:2020 for the co-ordination of MPSD with SCPD (8.2.5.4);
m) reference to IEC TR 63216 with different EMC environments (8.3.1);
n) reference to IEC TR 63201 for the embedded software design (8.4);
o) reference to IEC TS 63208 for cybersecurity aspects (8.5);
p) update and completion of the measurement method of the power consumption of the electromagnet (9.3.3.2.1.2);
q) update of Annex C including rational about AC-3e;
r) determination of the critical load current for photovoltaic applications (M.8.7).
- Standard385 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...