IEC 61400-1:2019/COR1:2019
(Corrigendum)Corrigendum 1 - Wind energy generation systems - Part 1: Design requirements
Corrigendum 1 - Wind energy generation systems - Part 1: Design requirements
General Information
Relations
Standards Content (Sample)
IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IEC 61400-1
Edition 4.0 2019-02
WIND ENERGY GENERATION SYSTEMS –
Part 1: Design requirements
CORRIGENDUM 1
3 Terms and definitions
3.60
turbulence standard deviation
Replace s by .
1 1
7 Structural design
7.6.2.4 Partial safety factors for resistances where
...
This May Also Interest You
IEC TS 61400-31:2023 establishes a guideline for the assessment of the risks which a wind turbine may pose to the general public.
This document aims to facilitate a uniform scope and a uniform use of methods in wind turbine risk assessments. This document covers risk due to internal or external causes, such as technical failures, human errors, extreme wind conditions, turbine icing, lightning strikes, earthquakes, flooding, landslides or fire.This document covers only onshore wind turbines with a horizontal axis and a swept area greater than 200 m2. Substations and other external structures are excluded.
This document describes risks during operation of the wind turbine including maintenance, idling and standstill. It does not describe risks during construction, civil works, crane operations, assembly or decommissioning.
Risks according to this document are assessed by prescriptive and/or risk-based methods.
This document covers risk reduction measures that might be necessary to reduce risk to a tolerable level.
- Technical specification56 pagesEnglish languagesale 15% off
IEC 61400-21-2:2023 defines and specifies the quantities that are determined to characterize the electrical characteristics of grid-connected power plants (PPs).
This document defines the measurement and test procedures for quantifying the electrical characteristics as basis for the verification of compliance of PPs. This document defines a uniform functionality test and measurement procedure for the power plant controller (PPC), as a basis for the unit test of the power plant controller.
This document defines the procedures for assessing compliance with electrical connection requirements, including the aggregation methods for power quality aspects such as voltage variations, flicker, harmonics and interharmonics. This document defines the procedures for measurement and fault recording, for example for the verification of power plant electrical simulation models in relation to undervoltage and overvoltage ride-through events.
- Standard302 pagesEnglish and French languagesale 15% off
IEC TS 61400-29:2023, which is a Technical Specification, instils good practice for aviation lighting and marking of wind turbines in both onshore and offshore domains. Consideration is given to visible lighting and infrared (IR) lighting, which is necessary to maintain conspicuity to users of night vision goggles (NVGs). ICAO Annex 14 Standards and Recommended Practices have been used as the basis to develop supplementary harmonised specifications to assist with implementation.
This document provides a set of technical requirements for marking and lighting of wind turbines with a tip height from/at 150 meters and below 315 meters Above Ground Level (AGL), or Above Mean Sea Level (AMSL) for offshore sites. This will improve situational awareness for airspace users, maintain safety of aircraft flying in the vicinity of wind turbines, and provide additional tools to assist with the reduction in environmental impacts consistent with aviation safety objectives.
- Technical specification30 pagesEnglish languagesale 15% off
IEC 61400-50-1:2022 specifies methods and requirements for the application of instruments to measure wind speed (and related parameters, e.g. wind direction, turbulence intensity). Such measurements are required as an input to some of the evaluation and testing procedures for wind energy and wind turbine technology (e.g. resource evaluation and turbine performance testing) described by other standards in the IEC 61400 series. This document is applicable specifically to the use of wind measurement instruments mounted on meteorological masts, turbine nacelles or turbine spinners which measure the wind at the location at which the instruments are mounted. This document excludes remote sensing devices which measure the wind at some location distant from the location at which the instrument is mounted (e.g. vertical profile or forward facing lidars).
- Standard162 pagesEnglish and French languagesale 15% off
IEC 61400-12-1:2022 specifies a procedure for measuring the power performance characteristics of a single wind turbine and applies to the testing of wind turbines of all types and sizes connected to the electrical power network. In addition, this document defines a procedure to be used to determine the power performance characteristics of small wind turbines (as defined in IEC 61400-2) when connected to either the electric power network or a battery bank. This document defines a measurement methodology that requires the measured power curve and derived energy production figures to be supplemented by an assessment of uncertainty sources and their combined effects. This third edition of IEC 61400-12-1 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard316 pagesEnglish and French languagesale 15% off
IEC 61400-12-2:2022 specifies a procedure for verifying the power performance characteristics of a single electricity-producing, horizontal axis wind turbine that is not considered to be a small wind turbine per IEC 61400-2. It is expected that this document be used when the specific operational or contractual specifications do not comply with the requirements set out in IEC 61400-12-1. The purpose of this document is to provide a uniform methodology of measurement, analysis, and reporting of power performance characteristics for individual electricity producing wind turbines utilising nacelle-anemometry methods. This document is intended to be applied only to horizontal axis wind turbines of sufficient size that the nacelle-mounted anemometer does not significantly affect the flow through the turbine’s rotor and around the nacelle and hence does not affect the wind turbine’s performance. This second edition of IEC 61400-12-2 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard160 pagesEnglish and French languagesale 15% off
IEC 61400-12:2022 defines procedures for assessing the power performance characteristics of wind turbines. This document provides a general introduction to the available options for power performance measurement and the contributing evaluations which are further detailed in the other parts of the IEC 61400-12 series. This first edition of IEC 61400-12 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard29 pagesEnglish and French languagesale 15% off
IEC 61400-12-6:2022 specifies a procedure for measuring the nacelle transfer function of a single electricity-producing, horizontal axis wind turbine, which is not considered to be a small wind turbine in accordance with IEC 61400-2. It is expected that this document be used when a valid nacelle transfer function is needed to execute a power performance measurement according to IEC 61400-12-2. This document specifies how to characterise a wind turbine's nacelle transfer function. The nacelle transfer function is determined by collecting simultaneous measurements of nacelle‑measured wind speed and free stream wind speed (as measured on a meteorological mast) for a period that is long enough to establish a statistically significant database over a range of wind speeds and under varying wind and atmospheric conditions. The procedure also provides guidance on determination of measurement uncertainty including assessment of uncertainty sources and recommendations for combining them.
This first edition of IEC 61400-12-6 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard114 pagesEnglish and French languagesale 15% off
IEC 61400-50:2022 provides a general introduction to the options that are available for wind measurement, which are further detailed in the other parts of the IEC 61400-50 series. Whereas those other standards define use-cases for wind measurements, the IEC 61400-50 series sets those wind measurement requirements which are independent of the use-case. Its purpose is to ensure that wind measurements and the evaluation of uncertainties in those measurements are carried out consistently across the wind industry and that wind measurements are carried out such that the uncertainties can be quantified and that those uncertainties are within an acceptable range.
This first edition of IEC 61400-50 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400-12-2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard25 pagesEnglish and French languagesale 15% off
IEC 61400-12-5:2022 specifies the procedures for assessing the significance of obstacles and terrain variations on a proposed power performance measurement site and applies to the performance testing of wind turbines of all types and sizes connected to the electrical power network as described in other parts of the IEC 61400 series. The procedure applies to the performance evaluation of specific wind turbines at specific locations.
This first edition of IEC 61400-12-5 is part of a structural revision that cancels and replaces the performance standards IEC 61400-12-1:2017 and IEC 61400-12-2:2013. The structural revision contains no technical changes with respect to IEC 61400-12-1:2017 and IEC 61400‑12‑2:2013, but the parts that relate to wind measurements, measurement of site calibration and assessment of obstacle and terrain have been extracted into separate standards.
- Standard49 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.