ISO 13507:2012

Rubber compounds, raw rubbers and compounding materials — Short terms for properties reported in certificates of analysis

ISO 13507:2012 provides a list of short terms for analytical characteristics to be used in certificates of analysis for rubber compounds, raw rubbers and compounding materials.

Mélanges de caoutchouc, caoutchoucs bruts et ingrédients de mélange — Noms courts pour les propriétés consignées dans les certificats d'analyse

General Information

• Status: Published
• Publication Date: 07-Nov-2012
• ICS: 83.060 - Rubber
• Technical Committee: ISO/TC 45 - Rubber and rubber products
• Drafting Committee: ISO/TC 45/WG 10 - Terminology
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 22-Aug-2022

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 13507
First edition
2012-11-15
Rubber compounds, raw rubbers
and compounding materials — Short
terms for properties reported in
certificates of analysis
Mélanges de caoutchouc, caoutchoucs bruts et ingrédients de
mélange — Noms courts pour les propriétés consignées dans les
certificats d’analyse
Reference number
ISO 13507:2012(E)
©
ISO 2012

---------------------- Page: 1 ----------------------
ISO 13507:2012(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the
address below or ISO’s member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 13507:2012(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13507 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products.
© ISO 2012 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 13507:2012(E)
Rubber compounds, raw rubbers and compounding
materials — Short terms for properties reported in
certificates of analysis
1 Scope
This International Standard provides a list of short terms for analytical characteristics to be used in
certificates of analysis for rubber compounds, raw rubbers and compounding materials.
2 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
2.1
common industrial term
one of the usual terms used to describe a characteristic
2.2
standard short term for certificate of analysis
term for a characteristic as written in the certificate of analysis
3 Short terms for analytical characteristics
Table 1 provides a list of the short-terms for analytical characteristics which shall be used in certificates
of analysis for rubber compounds, raw rubbers and compounding materials.
Table 1 — Short terms for analytical characteristics
Standard short term for
Common industrial term Unit
certificates of analysis
a
A/O 2246 A/O 2246 %
Acid number Acid number mg KOH/g
Active product content Active product % (by mass)
Additive content Additive % (by mass)
4 Aminodiphenylamine content 4ADPA content % (by mass)
Aggregate size distribution (ASD): average aggregate D nm
w
diameter
Aggregate size distribution (ASD): geometric mean aggre- X nm
g
gate mass
Aggregate size distribution (ASD): most frequent diameter D nm
mode
occurrence
Alkalinity (of latex) Alkalinity (of latex) % ammonia
Aluminium oxide content Al O content % (by mass)
2 3
a
Applicable to latex.
b
1 mPa⋅s = 1 cP.
c
Hexadecyl-trimethyl-ammonium bromide (IUPAC name).
d
1 mN/m = 1 dyn/cm.
© ISO 2012 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 13507:2012(E)

Table 1 (continued)
Standard short term for
Common industrial term Unit
certificates of analysis
Aluminium content Al content % (by mass)
Amine content Amine content % (by mass)
Ammonia content in latex NH content % (by mass)
3
Amount of matter insoluble in …. Matter insoluble in …. % (by mass)
Amount of matter soluble in …. Matter soluble in …. % (by mass)
Aniline point Aniline point °C
b
Apparent Brookfield viscosity Brookfield viscosity mPa⋅s
Aromatic carbon content CA content % (by mass)
Aromatic content Aromatic content % (by mass)
Asbestos content Asbestos content % (by mass)
Ash Ash at . °C % (by mass)
Assay of . Assay of . % (by mass)
Bay region hydrogen content H %
Bay
Bound-styrene content Bound-styrene content % (by mass)
Boric acid content Boric acid %
2
Brunauer, Emmett and Teller (BET) nitrogen surface area NSA m /g
(NSA)
2
Brunauer, Emmett and Teller (BET) statistical thickness STSA m /g
surface area (STSA)
3
Bulk density Bulk density kg/l or g/ml or g/cm
a
Butylated hydroxyanisole BHA %
a
Butylated hydroxytoluene BHT %
Cadmium content Cd content % (by mass)
Calcium content Ca content % (by mass)
Calcium carbonate content CaCO content % (by mass)
3
Carbon disulfide content CS content % (by mass)
2
Carbonyl content Carbonyl content % (by mass)
Chlorine content Cl content % (by mass)
Chromium content Cr content % (by mass)
Cloud point Cloud point °C
Coagulum content in latex Coagulum % (by mass)
Cobalt content Co content % (by mass)
Combined-sulfur content Combined-sulfur content % (by mass)
Copper content Cu content mg/kg
c 2
CTAB adsorption number (of carbon black) CTAB m /g
Cyclohexylamine content Cyclohexylamine content % (by mass)
3
Density at …. °C Density at …. °C kg/l or g/ml or g/cm
a
Applicable to latex.
b
1 mPa⋅s = 1 cP.
c
Hexadecyl-trimethyl-ammonium bromide (IUPAC name).
d
1 mN/m = 1 dyn/cm.
2 © ISO 2012 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 13507:2012(E)

Table 1 (continued)
Standard short term for
Common industrial term Unit
certificates of analysis
Dicyclohexylamine content Dicyclohexylamine content % (by mass)
a
Dip
...