ISO 17557:2003

Plastics — Film and sheeting — Cast polypropylene (PP) films

ISO 17557:2003 specifies the requirements for cast polypropylene (PP) films, which are mainly used for packaging.

Plastiques — Film et feuille — Films de polypropylène (PP) moulés

General Information

• Status: Published
• Publication Date: 09-Sep-2003
• ICS: 83.140.10 - Films and sheets
• Technical Committee: ISO/TC 61/SC 11 - Products
• Drafting Committee: ISO/TC 61/SC 11/WG 3 - Plastics films and sheeting
• Current Stage: 9093 - International Standard confirmed
• Completion Date: 04-Dec-2023

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 17557
First edition
2003-09-15
Plastics — Film and sheeting — Cast
polypropylene (PP) films
Plastiques — Film et feuille — Films de polypropylène (PP) moulés

Reference number
ISO 17557:2003(E)
©
ISO 2003

---------------------- Page: 1 ----------------------
ISO 17557:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
©
ii ISO 2003 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 17557:2003(E)
Contents Page
1 Scope . 1
2 Normative references . 1
3 Classification . 1
4 Requirements . 2
5 Test methods . 4
6 Packaging . 6
7 Marking . 6
©
ISO 2003 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 17557:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17557 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
It is based on Japanese Standard JIS Z 1713:1997.
©
iv ISO 2003 – All rights reserved

---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 17557:2003(E)
Plastics — Film and sheeting — Cast polypropylene (PP) films
1Scope
This International Standard specifies the requirements for cast polypropylene (PP) films, which are mainly used
for packaging.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition o
...