Non-destructive testing — Measurement and evaluation of the X-ray tube voltage — Part 3: Spectrometric method

ISO 16526-3:2011 specifies the test method for a non-invasive measurement of X-ray tube voltages using the energy spectrum of X-rays (spectrometric method). It covers the voltage range from 10 kV to 500 kV. The intention is to check the correspondence of the actual voltage with the indicated value on the control panel of the X-ray unit. It is intended to measure the maximum energy only and not the complete X-ray spectrum. The procedure is applicable for tank type and constant potential X-ray units.

Essais non destructifs — Mesurage et évaluation de la tension des tubes radiogènes — Partie 3: Méthode spectrométrique

L'ISO 16526-3:2011 décrit le mode opératoire de mesurage des tensions des tubes radiogènes à l'aide du spectre énergétique des rayons X (méthode spectrométrique). Elle couvre la plage de tensions comprises entre 10 kV et 500 kV. Le but est de vérifier la correspondance entre la tension effective et la valeur indiquée sur le tableau de commandes de l'unité à rayons X. L'objectif consiste à mesurer uniquement l'énergie maximale et non l'intégralité du spectre à rayons X. Le mode opératoire s'applique aux unités à rayons X à tension auto redressée et à tension constante.

General Information

Status
Published
Publication Date
14-Dec-2011
Current Stage
9093 - International Standard confirmed
Completion Date
08-Sep-2021
Ref Project

Relations

Buy Standard

Standard
ISO 16526-3:2011 - Non-destructive testing -- Measurement and evaluation of the X-ray tube voltage
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 16526-3:2011 - Essais non destructifs -- Mesurage et évaluation de la tension des tubes radiogenes
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16526-3
First edition
2011-12-15

Non-destructive testing — Measurement
and evaluation of the X-ray tube
voltage —
Part 3:
Spectrometric method
Essais non destructifs — Mesurage et évaluation de la tension des
tubes radiogènes —
Partie 3: Méthode spectrométrique




Reference number
ISO 16526-3:2011(E)
©
ISO 2011

---------------------- Page: 1 ----------------------
ISO 16526-3:2011(E)

COPYRIGHT PROTECTED DOCUMENT


©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2011 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16526-3:2011(E)
Contents Page

Foreword . iv
Introduction . v
1 Scope . 1
2 Definitions . 1
3 Test method . 1
4 Test report . 5
Annex A (informative) Selection of filters . 6
© ISO 2011 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 16526-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16526-3 was prepared by CEN (as EN 12544-3:1999) and is submitted for approval under a special “fast-
track procedure”, by Technical Committee ISO/TC 135, Non-destructive testing, Subcommittee SC 5,
Radiation methods, in parallel with its approval by the ISO member bodies (see the ISO/IEC Directives,
Part 1, “Fast-track procedure”).
ISO 16526 consists of the following parts, under the general title Non-destructive testing — Measurement and
evaluation of the X-ray tube voltage:
— Part 1: Voltage divider method
— Part 2: Constancy check by the thick filter method
— Part 3: Spectrometric method

iv © ISO 2011 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 16526-3:2011(E)
Introduction

In order to cover the different requirements for the measurement of the X-ray tube voltage, three different methods
are described in ISO 16526-1 to ISO 16526-3.
The voltage divider method (ISO 16526-1) enables a direct and absolute measurement of the average high voltage
of constant potential X-ray systems on the secondary side of the high voltage generator.
The thick filter method (ISO 16526-2) describes a constancy check. This method is recommended for the regular
stability check of an X-ray system.
The spectrometric method (ISO 16526-3) is a procedure for non-invasive measurement of the X-ray tube voltage
using the energy spectrum of the X-rays. This method can be applied for all X-ray systems and is the recommended
method whenever the voltage divider method is not applicable, e. g. in case of tank units where it is not possible to
connect the voltage divider device.
© ISO 2011 – All rights reserved v

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 16526-3:2011(E)

Non-destructive testing — Measurement and evaluation of
the X-ray tube voltage —
Part 3:
Spectrometric method

1 Scope
This part of ISO 16526 specifies the test method for a non-invasive measurement of X-ray tube voltages using the
energy spectrum of X-rays (spectrometric method). It covers the voltage range from 10 kV to 500 kV.
The intention is to check the correspondence of the actual voltage with the indicated value on the control panel of
the X-ray unit. It is intended to measure the maximum energy only and not the complete X-ray spectrum.
The procedure is applicable for tank type and constant potential X-ray units.
2 Definitions
For the purposes of this part of ISO 16526, the following definitions apply:
2.1 Energy dispersive photon detector
A photon detector, e. g. Ge based detector, which responds to incident photons with electric pulses, whose
amplitude are a measure for the energy of the photons.
2.2 Multi channel analyser
An electronic device which is capable of sorting incoming electric pulses according to their amplitude.
NOTE The pulses are sorted into storage registers or channels in such a way that the contents of a register or
channel is increased by one if a pulse occurs with the corresponding amplitude.
2.3 Energy spectrum
The graphical representation of the contents of the channels versus the
...

NORME ISO
INTERNATIONALE 16526-3
Première édition
2011-12-15

Essais non destructifs — Mesurage et
évaluation de la tension des tubes
radiogènes —
Partie 3:
Méthode spectrométrique
Non-destructive testing — Measurement and evaluation of the X-ray
tube voltage —
Part 3: Spectrometric method




Numéro de référence
ISO 16526-3:2011(F)
©
ISO 2011

---------------------- Page: 1 ----------------------
ISO 16526-3:2011(F)

DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2011
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2011– Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 16526-3:2011(F)
Sommaire Page

Avant-propos.iv
Introduction . v
1 Domaine d'application. 1
2 Définitions. 1
3 Méthode d'essai . 1
4 Rapport d'essai . 5
Annexe A (informative)  Choix des filtres . 6
© ISO 2011 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
ISO 16526-3:2011(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 16526-3 a été élaborée par le CEN (en tant que EN 12544-3:1999) et a été adoptée, selon une
procédure spéciale par «voie express», par le comité technique ISO/TC 135, Essais non destructifs, sous-
comité SC 5, Moyens utilisant les rayonnements, parallèlement à son approbation par les comités membres
de l'ISO (voir les Directives ISO/CEI, Partie 1, «Procédure par voie express»).
L'ISO 16526 comprend les parties suivantes, présentées sous le titre JpQpUDOEssais non destructifs —
Mesurage et évaluation de la tension des tubes radiogènes:
— Partie 1: Méthode par diviseur de tension
— Partie 2: Contrôle de la constance selon la méthode du filtre épais
— Partie 3: Méthode spectrométrique

iv © ISO 2011 – Tous droits réservés

---------------------- Page: 4 ----------------------
ISO 16526-3:2011(F)
Introduction

Trois méthodes différentes sont décrites dans l'ISO 16526-1, l'ISO 16526-2 et l'ISO 16526-3, afin de couvrir
les différentes exigences qui s'appliquent au mesurage de la tension des tubes radiogènes.
La méthode par diviseur de tension (ISO 16526-1) permet un mesurage direct et absolu de la haute tension
moyenne des installations radiogènes à tension constante (courant continu) du côté secondaire d'un générateur
haute tension.
La méthode du filtre épais (ISO 16526-2) décrit un essai comparatif. Cette méthode est recommandée pour les
vérifications de routine de la stabilité d'un tube radiogène.
La méthode spectrométrique (ISO 16526-3) est une méthode non invasive de mesurage de la tension des tubes
radiogènes au moyen du spectre d'énergie des rayons X. Cette méthode peut être employée pour tous les tubes
radiogènes, et est la méthode recommandée lorsque la méthode par diviseur de tension ne peut être appliquée,
comme dans le cas des réservoirs par exemple, sur lesquels il est impossible de raccorder un diviseur de tension.
© ISO 2011 – Tous droits réservés v

---------------------- Page: 5 ----------------------
NORME INTERNATIONALE ISO 16526-3:2011(F)

Essais non destructifs — Mesurage et évaluation de la tension
des tubes radiogènes —
Partie 3:
Méthode spectrométrique
1 Domaine d'application

La présente partie de l'ISO 16526 décrit le mode opératoire de mesurage des tensions des tubes radiogènes à
l'aide du spectre énergétique des rayons X (méthode spectrométrique). Elle couvre la plage de tensions comprises
entre 10 kV et 500 kV.
Le but est de vérifier la correspondance entre la tension effective et la valeur indiquée sur le tableau de
commandes de l'unité à rayons X. L'objectif consiste à mesurer uniquement l'énergie maximale et non l'intégralité
du spectre à rayons X.
Le mode opératoire s'applique aux unités à rayons X à tension auto-redressée et à tension constante.
2 Définitions
Pour les besoins de la présente partie de l'ISO 16526, les définitions suivantes s'appliquent.
2.1
photo-détecteur à dispersion d'énergie
photo-détecteur, par exemple détecteur de base Ge, qui fait correspondre aux photons incidents des impulsions
électriques dont l'amplitude est une mesure de l'énergie de ces photons
2.2
analyseur multi-voies
dispositif électronique capable de trier les impulsions électriques en entrée en fonction de leur amplitude
NOTE Les impulsions sont triées
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.