Reduction sleeves with 7/24 external and Morse internal taper and incorporated screw

ISO 5415:2007 specifies the dimensions of reduction sleeves with 7/24 external taper No. 30-40-45-50 and 60 and Morse internal taper No. 1 to 6 (Morse taper No. 4, 5 and 6 being either with positive drive or without positive drive). These sleeves permit driving of tools with Morse taper shanks with tapped holes with the aid of an internal screw. The form of this screw and its fixation in the sleeve are left to the manufacturer's discretion. 7/24 tapers are in accordance with ISO 297. Morse tapers are in accordance with ISO 296 and ISO 5413.

Douilles de réduction aux cônes extérieur 7/24 et intérieur Morse, avec vis incorporée

L'ISO 5415:2007 spécifie les dimensions des douilles de réduction au cône extérieur 7/24 N°30-40-45-50 et 60 et au cône intérieur Morse N°1 à 6 (les cônes Morse N°4-5 et 6 pouvant être à entraînement positif ou sans entraînement positif). Ces douilles permettent l'entraînement d'outils à queue cône Morse à trou taraudé au moyen d'une vis intérieure. La forme de cette vis ainsi que son mode de fixation sont laissés à l'initiative du fabricant. Les cônes 7/24 sont conformes à l'ISO 297. Les cônes Morse sont conformes à l'ISO 296 et à l'ISO 5413.

General Information

Status
Published
Publication Date
25-Nov-2007
Current Stage
9093 - International Standard confirmed
Completion Date
27-Mar-2023
Ref Project

Relations

Buy Standard

Standard
ISO 5415:2007 - Reduction sleeves with 7/24 external and Morse internal taper and incorporated screw
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 5415:2007 - Douilles de réduction aux cônes extérieur 7/24 et intérieur Morse, avec vis incorporée
French language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 5415
Second edition
2007-12-01
Reduction sleeves with 7/24 external and
Morse internal taper and incorporated
screw
Douilles de réduction aux cônes extérieur 7/24 et intérieur Morse, avec
vis incorporée
Reference number
ISO 5415:2007(E)
ISO 2007
---------------------- Page: 1 ----------------------
ISO 5415:2007(E)
PDF disclaimer

This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but

shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In

downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat

accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation

parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In

the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

COPYRIGHT PROTECTED DOCUMENT
© ISO 2007

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or

ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 5415:2007(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the

International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 5415 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 2, High speed

steel cutting tools and their attachments.

This second edition cancels and replaces the first edition (ISO 5415:1977), which has been technically revised.

© ISO 2007 – All rights reserved iii
---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 5415:2007(E)
Reduction sleeves with 7/24 external and Morse internal taper
and incorporated screw
1 Scope

This International Standard specifies the dimensions of reduction sleeves with 7/24 external taper

No. 30-40-45-50 and 60 and Morse internal taper No. 1 to 6 (Morse taper No. 4, 5 and 6 being either with

positive drive, see Figure 2, or without positive drive, see Figure 1).

These sleeves permit driving of tools with Morse taper shanks with tapped holes with the a

...

NORME ISO
INTERNATIONALE 5415
Deuxième édition
2007-12-01
Douilles de réduction aux cônes extérieur
7/24 et intérieur Morse, avec vis
incorporée
Reduction sleeves with 7/24 external and Morse internal taper and
incorporated screw
Numéro de référence
ISO 5415:2007(F)
ISO 2007
---------------------- Page: 1 ----------------------
ISO 5415:2007(F)
PDF – Exonération de responsabilité

Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier

peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence

autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées

acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute

responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.

Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info

du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir

l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,

veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2007

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit

de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2007 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 5415:2007(F)
Avant-propos

L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de

normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée

aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du

comité technique créé à cet effet. Les organisations internationales, gouvernementales et non

gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec

la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,

Partie 2.

La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur

publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres

votants.

L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de

droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne

pas avoir identifié de tels droits de propriété et averti de leur existence.

L'ISO 5415 a été élaborée par le comité technique ISO/TC 29, Petit outillage, sous-comité SC 2, Outils

coupants en acier rapide et leurs attachements.

Cette deuxième édition annule et la première édition (ISO 5415:1977), qui a fait l'objet d'une révision

technique.
© ISO 2007 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 5415:2007(F)
Douilles de réduction aux cônes extérieur 7/24 et intérieur
Morse, avec vis incorporée
1 Domaine d'application

La présente Norme internationale spécifie les dimensions des douilles de réduction au cône extérieur 7/24

N° 30-40-45-50 et 60 et au cône intérieur Morse N° 1 à 6 (les cônes Morse N° 4-5 et 6 pouvant être à

entraînement positif, voir Figure 2 ou sans entraînement positif, voir Figure 1).

Ces douilles permettent l'en
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.