Polyamide fibre ropes — Double braid construction

ISO 10554:2009 specifies requirements for double braided ropes and for higher-strength double braided ropes made of polyamide and gives rules for their designation.

Cordages en fibres de polyamide — Cordages coaxiaux

L'ISO 10554:2009 spécifie les exigences applicables aux cordages coaxiaux et aux cordages coaxiaux à haute résistance en polyamide et précise les règles pour leur désignation.

General Information

Status
Published
Publication Date
19-Nov-2009
Current Stage
9093 - International Standard confirmed
Completion Date
07-Oct-2020
Ref Project

Relations

Buy Standard

Standard
ISO 10554:2009 - Polyamide fibre ropes -- Double braid construction
English language
4 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 10554:2009 - Cordages en fibres de polyamide -- Cordages coaxiaux
French language
4 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10554
First edition
2009-12-01

Polyamide fibre ropes — Double braid
construction
Cordages en fibres de polyamide — Cordages coaxiaux




Reference number
ISO 10554:2009(E)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 10554:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10554:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10554 was prepared by Technical Committee ISO/TC 38, Textiles.

© ISO 2009 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 10554:2009(E)

Polyamide fibre ropes — Double braid construction
1 Scope
This International Standard specifies requirements for double braided ropes and for higher-strength double
braided ropes made of polyamide and gives rules for their designation.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1968, Fibre ropes and cordage — Vocabulary
ISO 2307, Fibre ropes — Determination of certain physical and mechanical properties
ISO 9554:2005, Fibre ropes — General specifications
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 1968 apply.
4 Designation
Fibre ropes shall be designated by the following:
⎯ the words “fibre rope”;
⎯ the number of this International Standard;
⎯ the reference number of the rope;
⎯ the material from which the rope is made;
⎯ the level of performance of rope: double braided rope or higher-strength (hs) double braided rope.
EXAMPLE 1 Designation of a double braided rope, reference number 20, corresponding to a linear density of 249 ktex
made of polyamide:
Fibre rope ISO 10554 - 20 - PA
EXAMPLE 2 Designation of a higher-strength (hs) double braided rope, reference number 20, corresponding to a
linear density of 249 ktex made of polyamide:
Fibre rope ISO 10554 - 20 - PA (hs)
© ISO 2009 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 10554:2009(E)
5 Material
The mixing of polyamide fibre types and grades shall not be permitted.
6 General requirements
6.1 Construction
Ropes produced according to this International Standard shall be constructed in the following way.
The rope (see Figure 1) shall be of a double braided construction wherein an inner braid of hollow structure
manufactured in a separate operation shall serve as the core, while a cover (outer braid) is braided over it in a
second operation. The weight of either the inner braid or the outer braid shall not exceed 55 % of the total
weight of the rope. It shall also conform to ISO 9554.

Figure 1 — Shape of a polyamide double b
...

NORME ISO
INTERNATIONALE 10554
Première édition
2009-12-01

Cordages en fibres de polyamide —
Cordages coaxiaux
Polyamide fibre ropes — Double braid construction




Numéro de référence
ISO 10554:2009(F)
©
ISO 2009

---------------------- Page: 1 ----------------------
ISO 10554:2009(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2009
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse

ii © ISO 2009 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 10554:2009(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
La tâche principale des comités techniques est d'élaborer les Normes internationales. Les projets de Normes
internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur
publication comme Normes internationales requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'ISO 10554 a été élaborée par le comité technique ISO/TC 38, Textiles.

© ISO 2009 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 10554:2009(F)

Cordages en fibres de polyamide — Cordages coaxiaux
1 Domaine d'application
La présente Norme internationale spécifie les exigences applicables aux cordages coaxiaux et aux cordages
coaxiaux à haute résistance en polyamide et précise les règles pour leur désignation.
2 Références normatives
Les documents de référence suivants sont indispensables pour l'application du présent document. Pour les
références datées, seule l'édition citée s'applique. Pour les références non datées, la dernière édition du
document de référence s'applique (y compris les éventuels amendements).
ISO 1968, Cordages en fibres et articles de corderie — Vocabulaire
ISO 2307, Cordages en fibres — Détermination de certaines caractéristiques physiques et mécaniques
ISO 9554:2005, Cordages en fibres — Spécifications générales
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions donnés dans l'ISO 1968 s'appliquent.
4 Désignation
Les cordages en fibres doivent être désignés par
⎯ le terme «cordage en fibres»;
⎯ le numéro de la présente Norme internationale;
⎯ le numéro de référence du cordage;
⎯ le matériau constitutif du cordage;
⎯ le niveau de performance du cordage: cordage coaxial ou cordage coaxial haute résistance (hr).
EXEMPLE 1 Désignation d'un cordage coaxial, numéro de référence 20, correspondant à une masse linéique de
249 ktex, fabriqué en polyamide:
Cordage en fibres ISO 10554 — 20 — PA
EXEMPLE 2 Désignation d'un cordage coaxial à haute résistance (hr), numéro de référence 20, correspondant à une
masse linéique de 249 ktex, fabriqué en polyamide:
Cordage en fibres ISO 10554 — 20 — PA (hr)
© ISO 2009 – Tous droits réservés 1

---------------------- Page: 4 ----------------------
ISO 10554:2009(F)
5 Matériau
Le mélange de différentes fibres et qualités de polyamide ne doit pas être autorisé.
6 Exigences générales
6.1 Construction
Les cordages fabriqués conformément à la présente Norme internationale doivent être constitués de la façon
suivante.
Le cordage (voir Figure 1) doit être réalisé par un double tressage dans lequel la tresse intérieure de structure
creuse et fabriquée séparément sert d'âme alors que la couverture (tresse extérieure) est tressée par dessus
lors d'une seconde opération. La masse de la tresse intérieure ou de la tresse extérieure ne doit pas dépasser
55 % de la masse totale du cordage. Elle doit aussi être conforme à l'ISO 9554.

Figure 1 — Forme d'un cordage coaxial
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.