ISO/IEC/IEEE 80005-1:2012

Utility connections in port — Part 1: High Voltage Shore Connection (HVSC) Systems — General requirements

IEC/ISO/IEEE 80005-1:2012(E) describes high voltage shore connection (HVSC) systems, on board the ship and on shore, to supply the ship with electrical power from shore. This standard is applicable to the design, installation and testing of HVSC systems and addresses: - HV shore distribution systems; - shore-to-ship connection and interface equipment; - transformers/reactors; - semiconductor/rotating convertors; - ship distribution systems; and - control, monitoring, interlocking and power management systems. It does not apply to the electrical power supply during docking periods, e.g. dry docking and other out of service maintenance and repair.

Alimentation des navires à quai — Partie 1: Systèmes de connexion à quai à haute tension — Exigences générales

General Information

• Status: Withdrawn
• Publication Date: 12-Jul-2012
• Withdrawal Date: 12-Jul-2012
• ICS: 47.020.60 - Electrical equipment of ships and of marine structures
• Technical Committee: ISO/TC 8/SC 3 - Piping and machinery
• Drafting Committee: ISO/TC 8/SC 3 - Piping and machinery
• Current Stage: 9599 - Withdrawal of International Standard
• Completion Date: 22-Mar-2019

Relations

• Revised: IEC/IEEE 80005-1:2019 - Utility connections in port — Part 1: High voltage shore connection (HVSC) systems — General requirements
• Effective Date: 03-Aug-2013
• Revises: IEC/PAS 60092-510:2009 - Electrical installations in ships — Special features — High Voltage Shore Connection Systems (HVSC-Systems) — Part 510:
• Effective Date: 04-Feb-2009

Standards Content (Sample)

IEC/ISO/IEEE 80005-1
Edition 1.0 2012-07
INTERNATIONAL
STANDARD
STANDARD




Utility connections in port –
Part 1: High Voltage Shore Connection (HVSC) Systems – General requirements

IEC/ISO/IEEE 80005-1:2012(E)

---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2012 IEC/ISO/IEEE

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
IEC, ISO or IEEE at the respective address given below.

IEC Central Office ISO copyright office Institute of Electrical and Electronics Engineers, Inc.

3, rue de Varembé Case postale 56 3 Park Avenue
CH-1211 Geneva 20 CH-1211 Geneva 20 New York, NY 10016-5997
Switzerland Switzerland United States of America
Tel.: [phone] Tel.: [phone] [e-mail]
Fax: [phone] Fax: [phone] www.ieee.org
[e-mail] [e-mail]
www.iec.ch www.iso.org

About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.

Useful links:

IEC publications search - www.iec.ch/searchpub Electropedia - www.electropedia.org
The advanced search enables you to find IEC publications The world's leading online dictionary of electronic and
by a variety of criteria (reference number, text, technical electrical terms containing more than 30 000 terms and
committee,…). definitions in English and French, with equivalent terms in
It also gives information on projects, replaced and additional languages. Also known as the International
withdrawn publications. Electrotechnical Vocabulary (IEV) on-line.

IEC Just Published - webstore.iec.ch/justpublished Customer Service Centre - webstore.iec.ch/csc
Stay up to date on all new IEC publications. Just Published If you wish to give us your feedback on this publication
details all new publications released. Available on-line and or need further assistance, please contact the
also once a month by email. Customer Service Centre: [e-mail].

---------------------- Page: 2 ----------------------
IEC/ISO/IEEE 80005-1


Edition 1.0 2012-07








INTERNATIONAL



STANDARD















Utility connections in port –

Part 1: High Voltage Shore Connection (HVSC) Systems – General requirements




























INTERNATIONAL

ELECTROTECHNICAL

COMMISSION

PRICE CODE
XB


ICS 47.020.60 ISBN 978-2-83220-111-4



  Warning! Make sure that you obtained this publication from an authorized distributor.

---------------------- Page: 3 ----------------------
– 2 – 80005-1 © IEC/ISO/IEEE:2012(E)
CONTENTS
FOREWORD . 5
INTRODUCTION . 7
1 Scope . 8
2 Normative references . 8
3 Terms and definitions . 10
4 General requirements . 11
4.1 System description . 11
4.2 Distribution system . 12
4.2.1 General . 12
4.2.2 Equipotential bonding . 12
4.3 Compatibility assessment before connection . 12
4.4 HVSC system design and operation . 13
4.4.1 System design . 13
4.4.2 System operation. 13
4.5 Personnel safety . 13
4.6 Design requirements . 13
4.6.1 General . 13
4.6.2 Protection against moisture and condensation . 13
4.6.3 Location and construction . 13
4.6.4 Electrical equipment in areas where flammable gas or vapour and/or

combustible dust may be present. 14
4.7 Electrical requirements . 14
4.8 System study and calculations. 15
4.9 Emergency shutdown including emergency stop facilities . 15
5 HV shore supply system requirements . 17
5.1 Voltages and frequencies . 17
5.2 Quality of HV shore supply . 18
6 Shore side installation . 19
6.1 General . 19
6.2 System component requirements . 19
6.2.1 Circuit-breaker, disconnector and earthing switch . 19
6.2.2 Transformer . 19
6.2.3 Neutral earthing resistor . 20
6.2.4 Equipment earthing conductor bonding . 20
6.3 Shore to ship electrical protection system. 20
6.4 HV interlocking . 21
6.4.1 General . 21
6.4.2 Handling of HV plug/socket-outlets . 21
6.4.3 Operating of the high-voltage (HV) circuit-breakers, disconnectors
and earthing switches . 21
6.5 Shore connection convertor equipment . 22
6.5.1 General . 22
6.5.2 Degree of protection . 22
6.5.3 Cooling . 22
6.5.4 Protection . 23
7 Ship to shore connection and interface equipment . 23

---------------------- Page: 4 ----------------------
80005-1 © IEC/ISO/IEEE:2012(E) – 3 –
7.1 General . 23
7.2 Cable management system . 23
7.2.1 General . 23
7.2.2 Monitoring of cable tension . 24
7.2.3 Monitoring of the cable length . 24
7.2.4 Connection conductor current unbalance protection. 24
7.2.5 Equipotential bond monitoring . 25
7.2.6 Slip ring units . 25
7.3 Plugs and socket-outlets . 25
7.3.1 General . 25
7.3.2 Pilot contacts . 26
7.3.3 Earth contact . 26
7.3.4 Fibre optical plug/socket . 26
7.4 Interlocking of earthing switches . 26
7.5 Ship to shore connection cable . 27
7.6 Independent control and monitoring cable . 27
7.7 Storage . 27
7.8 Data communication . 27
8 Ship requirements . 28
8.1 General . 28
8.2 Ship electrical distribution system protection . 28
8.2.1 Short-circuit protection . 28
8.2.2 Earth fault protection, monitoring and alarm . 28
8.3 Shore connection switchboard . 28
8.3.1 General . 28
8.3.2 Circuit-breaker, disconnector and earthing switch . 29
8.3.3 Instrumentation and protection . 29
8.4 On board transformer . 29
8.5 On board receiving switchboard connection point . 30
8.5.1 General . 30
8.5.2 Circuit-breaker and earthing switch. 30
8.5.3 Instrumentation. 30
8.5.4 Protection . 30
8.5.5 Operation of the circuit-breaker . 31
8.6 Ship power restoration . 32
9 HVSC system control and monitoring. 32
9.1 General requirements . 32
9.2 Load transfer via blackout . 33
9.3 Load transfer via automatic synchronization . 33
9.3.1 General . 33
9.3.2 Protection requirements . 33
10 Verification and testing . 33
10.1 General . 33
10.2 Initial tests of shore side installation . 34
10.2.1 General . 34
10.2.2 Tests . 34
10.3 Initial tests of ship side installation . 34
10.3.1 General . 34
10.3.2 Tests . 34

---------------------- Page: 5 ----------------------
– 4 – 80005-1 © IEC/ISO/IEEE:2012(E)
10.4 Tests at the first call at a shore supply point . 35
10.4.1 General . 35
10.4.2 Tests . 35
11 Periodic tests and maintenance . 35
11.1 General . 35
11.2 Tests at repeated calls of a shore supply point . 36
11.2.1 General . 36
11.2.2 Verification . 36
12 Documentation . 36
12.1 General . 36
12.2 System description . 36
Annex A (informative) Ship to shore connection cable . 37
Annex B (normative) Additional requirements for Roll-on Roll-off (Ro-Ro) cargo ships
and Ro-Ro passenger ships . 42
Annex C (normative) Additional requirements for cruise ships . 45
Annex D (normative) Additional requirements of container ships . 51
Annex E (normative) Additional requirements of liquefied natural gas carriers (LNGC) . 55
Annex F (normative) Additional requirements for tankers . 60
Bibliography . 63

Figure 1 – Block diagram of a typical described HVSC system arrangement . 11
Figure 2 – Phase sequence rotation – Positive direction . 17
Figure 3 – Balanced three-phase variables in time domain . 18
Figure A.1 – Bending test arrangement . 41
Figure B.1 – Example for general system layout . 42
Figure B.2 – Example of a safety circuit . 43
Figure B.3 – Power plug and socket pin assignment . 44
Figure C.1 – General system layout . 45
Figure C.2 – Cruise ship HVSC system single line diagram . 46
Figure C.3 – Example of safety and control circuit . 47
Figure C.4 – Shore power connector pin assignment . 49
Figure C.5 – The power inlet fitted with fail-safe limit switch . 50
Figure D.1 – General system layout . 51
Figure D.2 – Safety circuits . 53
Figure D.3 – Power plug and socket pin assignment . 54
Figure E.1 – General system layout . 55
Figure E.2 – Power plug and socket pin assignment . 58
Figure F.1 – General system layout . 60
Figure F.2 – Power plug and socket pin assignment . 61

3
Table E.1 – LNGC 140 000 – 225 000 m . 56
3
Table E.2 – LNGC > 225 000 m . 57

---------------------- Page: 6 ----------------------
80005-1 © IEC/ISO/IEEE:2012(E) – 5 –
UTILITY CONNECTIONS IN PORT –

Part 1: High Voltage Shore Connection (HVSC) Systems –
General requirements


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation.
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
IEEE Standards documents are developed within IEEE Societies and Standards Coordinating Committees of the
IEEE Standards Association (IEEE-SA) Standards Board. IEEE develops its standards through a consensus
development process, approved by the American National Standards Institute, which brings together volunteers
representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily
members of IEEE and serve without compensation. While IEEE administers the process and establishes rules
to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or
verify the accuracy of any of the information contained in its standards. Use of IEEE Standards documents is
wholly voluntary. IEEE documents are made available for use subject to important notices and legal disclaimers
(see http://standards.ieee.org/IPR/disclaimers.html for more information).
IEC collaborates closely with ISO and IEEE in accordance with conditions determined by agreement between
the organizations. This Triple Logo International Standard was jointly developed by the IEC, ISO and IEEE
under the terms of that agreement.
2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of
opinion on the relevant subjects since each technical committee has representation from all interested IEC
National Committees. In the ISO, Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International Standard requires approval by at
least 75 % of the member bodies casting a vote. The formal decisions of IEEE on technical matters, once
consensus within IEEE Societies and Standards Coordinating Committees has been reached, is determined by
a balanced ballot of materially interested parties who indicate interest in reviewing the proposed standard. Final
approval of the IEEE Standard document is given by the IEEE Standards Association (IEEE-SA) Standards
Board.
3) IEC/ISO/IEEE Publications have the form of recommendations for international use and are accepted by IEC
National Committees/ISO member bodies /IEEE Societies in that sense. While all reasonable efforts are made
to ensure that the technical content of IEC/ISO/IEEE Publications is accurate, IEC, ISO or IEEE cannot be held
responsible for the way in which they are used or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
(including IEC/ISO/IEEE Publications) transparently to the maximum extent possible in their national and
regional publications. Any divergence between any IEC/ISO/IEEE Publication and the corresponding national or
regional publication shall be clearly indicated in the latter.
5) IEC, ISO and IEEE do not provide any attestation of conformity. Independent certification bodies provide
conformity assessment services and, in some areas, access to IEC marks of conformity. IEC, ISO and IEEE are
not responsible for any services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC, ISO or IEEE or their directors, employees, servants or agents including
individual experts and members of technical committees and IEC National Committees and ISO member
bodies, or volunteers of IEEE Societies and the Standards Coordinating Committees of the IEEE Standards
Association (IEEE-SA) Standards Board, for any personal injury, property damage or other damage of any
nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the
publication, use of, or reliance upon, this IEC/ISO/IEEE Publication or any other IEC, ISO or IEEE Publications.
8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that implementation of this IEC/ISO/IEEE Publication may require use of
material covered by patent rights. By publication of this standard, no position is taken with respect to the
existence or validity of any patent rights in connection therewith. IEC, ISO or IEEE shall not be held responsible
for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the

---------------------- Page: 7 ----------------------
– 6 – 80005-1 © IEC/ISO/IEEE:2012(E)
legal validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in
connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or
non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent
rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be
obtained from ISO or the IEEE Standards Association.
International Standard IEC/ISO/IEEE 80005-1 has been prepared by IEC technical committee
18: Electrical installations of ships and of mobile and fixed offshore units, in cooperation with
IEC subcommittee 23H: Industrial plugs and socket-outlets, of IEC technical committee 23:
Electrical accessories; ISO technical committee 8: Ships and marine technology,
subcommittee 3: Piping and machinery; and IEEE IAS Petroleum and Chemical Industry
1
Committee (PCIC) of the Industry Applications Society of the IEEE .
This publication is published as an IEC/ISO/IEEE triple logo and prefix standard.
This document cancels and replaces IEC/PAS 60092-510 published in 2009.
A list of all the parts in the IEC 80005 series, published under the general title Utility
connections in port, can be found on the IEC website.
The text of this standard is based on the following IEC documents:
FDIS Report on voting
18/1254/FDIS 18/1268/RVD

Full information on the voting for the approvals of this standard can be found in the report on
voting indicated in the above table. In ISO, the standard has been approved by 9 members
out of 9 having a cast vote.
International standards are drafted in accordance with the rules given in the ISO/IEC
Directives, Part 2.
The IEC Technical Committee, the ISO Technical Committee and IEEE Technical Committee
have decided that the contents of this publication will remain unchanged until the stability date
indicated on the IEC, ISO and IEEE web site in the data related to the specific publication. At
this date, the publication will be
• reconfirmed
• withdrawn
• replaced by a revised edition, or
• amended.

___________
1
A list of IEEE participants can be found at the following URL:
http://standards.ieee.org/downloads/80005-1/80005-1-2012/80005-1-2012_wg-participants.pdf

---------------------- Page: 8 ----------------------
80005-1 © IEC/ISO/IEEE:2012(E) – 7 –
INTRODUCTION
The following standard was developed jointly between IEC technical committee 18: Electrical
installations of ships and of mobile and fixed offshore units, ISO technical committee 8: Ships
and marine technology, subcommittee 3: Piping and machinery, and IEEE IAS PCIC Marine
industry subcommittee.
For a variety of reasons, including environmental considerations, it is becoming an
increasingly common requirement for ships to shut down ship generators and to connect to
shore power for as long as practicable during stays in port. The scenario of receiving
electrical power and other utilities from shore is historically known as “cold ironing”.
The intention of this standard is to define requirements that support, with the application of
suitable operating practices, efficiency and safety of connections by compliant ships to
compliant high-voltage shore power supplies through a compatible shore to ship connection.
With the support of sufficient planning, cooperation between ship and terminal facilities, and
appropriate operating procedures and assessment, compliance with the requirements of this
standard is intended to allow different ships to connect to high-voltage shore connections
(HVSC) at different berths. This provides the benefits of standard, straightforward connection
without the need for adaptation and adjustment at different locations that can satisfy the
requirement to connect for as long as practicable during stays in port.
Ships that do not apply this standard may find it impossible to connect to compliant shore
supplies.
Where deviations from the requirements and recommendations in this standard may be
considered for certain designs, the potential effects on compatibility are highlighted.
Where the requirements and recommendations of this standard are complied with, high-
voltage shore supplies arrangements are likely to be compatible for visiting ships for
connection.
Clauses 1 to 12 are in
...