This document specifies requirements for electrically operated bilge pumps intended for use in
removing bilge water. It applies to:
— direct current (DC) bilge pumps which operate at a nominal voltage not exceeding 50 V; and
— single phase alternating current (AC) bilge pumps which operate at a nominal voltage not
exceeding 250 V.
It does not cover pumps intended for damage control.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies the requirements for the design, construction and installation of the following
types of DC and AC electrical systems, installed on small craft either individually or in combination:
a) extra-low-voltage direct current (DC) electrical systems that operate at nominal potentials of
50 V DC or less;
b) single-phase alternating current (AC) systems that operate at a nominal voltage not exceeding
AC 250 V.
This document does not cover the following:
— electrical propulsion systems of direct current less than 1 500 V DC, single-phase alternating
current up to 1 000 V AC, and three-phase alternating current up to 1 000 V AC, which are addressed
by ISO 16315;
— any conductor that is part of an outboard engine assembly and that does not extend beyond the
outboard engine manufacturers supplied cowling;
— three-phase AC installations that operate at a nominal voltage not exceeding 500 V AC, which are
addressed by IEC 60092-507.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC/IEEE 61886-1:2021 is applicable to single and three-phase wet-mateable and dry-mateable AC connectors, penetrators and jumper assemblies with rated voltages from 3 kV (Umax = 3,6 kV) to 30 kV (Umax = 36 kV). This document relates to the requirements and tests for products in the "as manufactured and supplied" condition. This document is not applicable to requirements and tests for products that have been subsequently installed, deployed or retrieved.

  • Standard
    96 pages
    English language
    sale 15% off

IEC 61800-5-3:2021, which is a product standard, specifies requirements and makes recommendations for the design and development, integration and validation of safety-related encoder (Encoder(SR)) in terms of their functional safety considerations, electrical safety and environmental conditions. It applies to Encoder(SR), being sensors as part of a PDS(SR). This document can also be referred to and used for Encoder(SR) in any other safety-related application, for example safety-related position monitoring.
This document is applicable where functional safety of an encoder is claimed and the Encoder(SR) is operating mainly in the high demand or continuous mode. The requirements of IEC 61800-5-2:2016 for PDS(SR) apply to Encoder(SR) as applicable.
This document includes additional or different requirements for Encoder(SR). It sets out safety-related considerations of Encoder(SR) in terms of the framework of IEC 61508 (all parts), and introduces requirements for Encoder(SR) as subsystems of a safety-related system. It is intended to facilitate the realisation of the electrical/electronic/programmable electronic (E/E/PE) and mechanical parts of an Encoder(SR) in relation to the safety performance of safety sub-function(s) of an Encoder(SR).

  • Standard
    215 pages
    English and French language
    sale 15% off

IEC 60092-360:2021 is available as IEC 60092-360:2021 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092:2021 specifies the requirements for electrical, mechanical and particular characteristics of insulating and sheathing materials intended for use in shipboard and fixed and mobile offshore unit power, control, instrumentation and telecommunication cables.

  • Standard
    26 pages
    English language
    sale 15% off

EN-ISO 25197 establishes the requirements for the design, construction and testing of electrical/electronic steering, shift and throttle systems and dynamic positioning control systems, or combinations thereof, on small craft of up to 24 m length of hull.This document does not apply to electric trolling motors and autopilot systems on sailing craft.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60092-354:2020 is available as IEC 60092-354:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-354:2020 is applicable to shipboard and offshore power cables with extruded solid insulation, conductor and core screening, having a voltage rating of one of the following: 3,6/6 (7,2) kV,6/10 (12) kV, 8,7/15 (17,5) kV, 12/20 (24) kV, 18/30 (36) kV. The cables are intended for fixed installations. The various types of power cables are given in 5.1. The constructional requirements and test methods are aligned with those indicated in IEC 60092-350, unless otherwise specified in this document.
The object of this document is:
- to standardize cables whose safety and reliability is ensured when they are installed in accordance with the requirements of IEC 60092-352 or IEC 61892-4;
- to lay down standard manufacturing requirements and characteristics of such cables directly or indirectly bearing on safety;
- to specify test methods for checking conformity with those requirements.
Only radial field cables are covered. This fourth edition cancels and replaces the third edition published in 2014. This edition constitutes a technical revision.

  • Standard
    36 pages
    English and French language
    sale 15% off

IEC 60092-350:2020 is available as IEC 60092-350:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-350:2020 provides the general constructional requirements and test methods for use in the manufacture of electric power, control and instrumentation cables with copper conductors intended for fixed electrical systems at voltages up to and including 18/30(36) kV on board ships and offshore (mobile and fixed) units.
The reference to fixed systems includes those that are subjected to vibration (due to the movement of the ship or installation) or movement (due to motion of the ship or installation) and not to those that are intended for frequent flexing. Cables suitable for frequent or continual flexing use are detailed in other IEC standards, for example IEC 60227 (all parts) and IEC 60245 (all parts), and their uses are restricted to those situations which do not directly involve exposure to a marine environment, for example, portable tools and domestic appliances.
The following types of cables are not included:
- optical fibre;
- sub-sea and umbilical cables;
- data and communication cables;
- coaxial cables.
This fifth edition cancels and replaces the fourth edition published in 2014 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) more detailed description of the test procedures in 7.7.6 and 7.7.7;
b) description of the relationship between Annex A and Annex D.

  • Standard
    107 pages
    English and French language
    sale 15% off

IEC TR 60092-370:2019 is available as IEC TR 60092-370:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC TR 60092-370:2019 gives guidance and lays down the basic recommendations for the selection and installation of shipboard and offshore unit cables intended for electrical systems used in both essential and non-essential analogue or digital signal communication, transmission and control networks, including types suitable for high-frequency signals (i.e. signals with a frequency of more than 105 Hz). These cables are not suitable for direct connection to low impedance supplies. Where such cables are required, attention is drawn to IEC 60092-353. Cables intended to have limited circuit integrity (fire resistance) when affected by fire are not covered by this document. Fibre optical cables are not included. Sub-sea or umbilical cables are not included. This second edition cancels and replaces the first edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical change with respect to the previous edition: 30 V AC was added in voltage rating for data cables.

  • Technical report
    18 pages
    English language
    sale 15% off

IEC 60092-302-2:2019 defines the specific requirements of low voltage marine power switchgear and controlgear assemblies (MPSC-assemblies) as follows:
- stationary assemblies with enclosure for which the rated voltage does not exceed 1 000 V AC or 1500 V DC;
- assemblies intended for use in conjunction with the power generation, distribution and conversion of electric energy, and for the control of electric energy consuming equipment.
This document applies to all assemblies whether they are designed, manufactured and verified on a one-off basis or fully standardised and manufactured in quantity.
The manufacture and/or assembly can be carried out other than by the original manufacturer.
This document does not apply to individual devices and self-contained components, such as motor starters, fuse switches, electronic equipment, which comply with the relevant product standards.
This first edition cancels and replaces the fourth edition of IEC 60092-302 published in 1997. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) this document has been renumbered to fall in line with IEC 61439 (all parts);
b) this document has been restructured to fall in line with IEC 61439 (all parts);
c) the creepage distances have been modified;
d) the references to non type tested assemblies (NTTA) have been removed;
e) non-applicable tables have been removed;
f) the applicability of IEC 61439 (all parts) annexes have been identified.
g) specific requirements that were detailed in IEC 60092-302:1997, covered under 7.6.101 have partly been moved to 60092-201.

  • Standard
    24 pages
    English language
    sale 15% off

IEC 60092-201:2019 is applicable to the main features of system design of electrical installations for use in ships.This fifth edition cancels and replaces the fourth edition, published in 1994. It constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) a new subclause regarding studies and calculations has been added;
b) a new subclause regarding documentation has been added;
c) the clause regarding distribution systems has been rewritten;
d) a clause regarding system earthing has been added;
e) the clause regarding sources of electrical power has been rewritten;
f) the clause regarding distribution system requirements has been rewritten;
g) the clause regarding cables has been deleted and transferred to IEC 60092-401;
h) a new subclause regarding electric and electrohydraulic steering gear has been added.

  • Standard
    42 pages
    English language
    sale 15% off

This document specifies requirements for electrical installations for the shore supply of berthing inland navigation vessels with electrical energy, three-phase current 400 V, 50 Hz with a rated current of up to 125 A.
This document applies to the supply of inland navigation vessels in ports and moorings for commercial inland navigation.
This part of EN 15869 specifies general requirements and contains information on the billing procedure.
For the supply of small craft and houseboats in marinas and similar installations, the requirements of IEC 60364 7 709 apply.
For electrical shore connections with a current rating more than 125 A, which are suitable for passenger ships with hotel operation, EN 16840 applies.
The requirements for the HD 60364 and HD 384 series generally apply to low-voltage systems on shore. A detailed list of the relevant parts is given in the Bibliography.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies in connection with EN 15869 1 for the supply of berthed inland navigation vessels with electrical energy.
This part of EN 15869 specifies additional requirements for the on-shore unit of the electrical shore connection.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies in connection with EN 15869 1 for the supply of berthed inland navigation vessels with electrical energy from shore.
This part of EN 15689 specifies additional requirements for the shore connection cable and the on-board unit of the electrical shore connection.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies in connection with EN 15869-1 for the supply of berthed inland navigation vessels with electrical energy.
This document specifies additional requirements for the on-shore unit of the electrical shore connection.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document applies in connection with EN 15869 1 for the supply of berthed inland navigation vessels with electrical energy from shore.
This document specifies additional requirements for the shore connection cable and the feeding unit of the electrical shore connection.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This document specifies requirements for electrical installations for the shore supply of berthing inland navigation vessels with electrical energy, three-phase current 400 V, 50 Hz with a rated current of up to 125 A.
This document applies to the supply of inland navigation vessels in ports and moorings for commercial inland navigation.
This document specifies general requirements and contains information on the billing procedure.
For the supply of small craft and houseboats in marinas and similar installations the requirements of HD 60364-7-709 apply.
For electrical shore connections with a current rating more than 125 A, which are suitable for passenger ships with hotel operation, EN 16840 applies.
The requirements for the HD 60364 series and HD 384 series generally apply to low-voltage systems on shore. A detailed list of the relevant parts is given in the Bibliography.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 61892-1:2019 is available as IEC 61892-1:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61892-1:2019 is applicable to electrical installations and equipment in mobile and fixed offshore units, including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or hand-held, to AC installations and DC installations without any voltage level limitation. Referenced equipment standards may give voltage level limitations.
This document specifies requirements such as those concerning
– environmental conditions,
– power supply characteristics,
– location of electrical equipment in units,
– protection against external influences,
– protection against electrical shock, and
– ignition source control.
This document gives information and guidance on topics such as
– cold climate protection, and
– surface treatment and protective painting system.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This fourth edition cancels and replaces the third edition published in 2015. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) voltage limitations have been removed;
b) definitions for fixed offshore units and mobile offshore units have been included;
c) tables for ambient air temperature and relative humidity have been removed, as this information will normally be given in owner's/operator's documentation for specific projects;
d) the requirement as to ignition source control has been moved from IEC 61892-7 to this document;
e) tables for voltage characteristics have been updated;
f) requirements for a minimum degree of protection for equipment have been moved from IEC 61892-2 to this document.

  • Standard
    71 pages
    English and French language
    sale 15% off

IEC 61892-4:2019 is applicable to the selection of electrical cables intended for fixed electrical systems in mobile and fixed offshore units, including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
This document specifies requirements such as those concerning
– types of cables,
– voltage rating of cables,
– cables and wiring for interconnection of equipment,
– current-carrying capacities for continuous service,
– correction factors for different ambient temperature and for short time duty, and
– short-circuit withstand capacity.
This document also gives information on the jet fire test for hydrocarbon (HCF) fire resistant cables.
The reference to fixed electrical systems includes those subjected to vibration due to the movement of the unit, for example, cables installed on a drag chain, and not those intended for repeated flexing. This document does not cover flexible cables, for example, those used on drilling decks for top-drive, or cables for portable equipment.
This document is applicable for cables with a rated voltage up to and including 18/30 kV AC and makes reference to cable standards developed by SC 18A.
For higher voltages, relevant standards developed by TC 20 are applicable.
This document does not apply to
– optical fibre cables,
– sub-sea and umbilical cables;,
– cables supplying downhole pumps, and
– data, telecommunication and radio frequency cables.
This second edition cancels and replaces the first edition published in 2007. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) construction requirements for cables have been removed; reference is made to relevant standards from Subcommittee (SC) 18A;
b) reference is made to standards from IEC TC 20 for cables with rated voltage above 30 kV;
c) tables for current-carrying capacities for defined installations have been removed; reference is made to relevant standards from IEC TC 64;
d) requirements as to the sizes of earth continuity conductors not contained in a cable have been moved to IEC 61892-6;
e) requirements as to fire stops have been deleted;
f) requirements as to tests for cables exposed to drilling fluids have been removed; reference is made to relevant standards from IEC SC 18A;
g) the procedure for tests of jet fire resistant cables has been updated;
h) requirements as to the design of cable systems have been moved to IEC 61892-2;
i) requirements in relation to the installation of cables have been moved to IEC 61892-6.

  • Standard
    41 pages
    English and French language
    sale 15% off

IEC 61892-5:2019 specifies additional characteristics for electrical installations in mobile units.
It applies to installations that depend on buoyancy, such as column-stabilized units (semi­submersible units), ship- or barge-type units as well as self-elevating units. It specifies additional characteristics for such units, used during transfer from one location to another and for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or hand-held, to AC installations and DC installations without any limitation on voltage level. Referenced equipment standards may give voltage level limitations.
This document specifies requirements such as those concerning
– environmental conditions,
– limits of inclination for the unit where the equipment is required to operate,
– bilge pumps,
– navigation and obstruction lights,
– steering gear,
– ballast system,
– jacking systems, and
– anchoring systems.
For electric propulsion, reference is made to IEC 60092-501.
For dynamic positioning systems, reference is made to relevant IMO requirements.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This fourth edition cancels and replaces the third edition published in 2014. This edition constitutes a technical revision.
This edition includes the following significant technical change with respect to the previous edition:
a) the technical requirements as to electric propulsion have been replaced with a reference to IEC 60092-501:2013;
b) the requirement for handrails on main and emergency switchboards has been added;
c) requirements as to control systems and indicators for watertight doors and hatch covers have been made more specific;
d) requirements concerning the holding capacity for jacking systems have been rewritten;
e) requirements as to thruster-assisted mooring system have been rewritten;
f) the annex regarding enhanced system verification (HIL test) for dynamic positioned mobile units has been relocated to IEC 61892-2:2019.

  • Standard
    51 pages
    English and French language
    sale 15% off

IEC 61892-7:2019 provides requirements for hazardous area classification and selection of electrical equipment and installation in hazardous areas in mobile and fixed offshore units, including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or personal, to AC installations and DC installations without any voltage level limitation. Referenced equipment standards may give voltage level limitations.
This document is based on the requirements of International Standards developed by IEC TC 31 regarding area classification and requirements as to installations in hazardous areas and gives additional requirements for installations on mobile and fixed offshore units.
This document specifies requirements such as those concerning
– area classification,
– electrical systems,
– selection of electrical equipment,
– cables and wiring systems,
– ventilation,
– ventilation requirement for battery compartments, and
– inspection, maintenance, repair and overhaul.
This document gives information on topics such as
– gas detection systems, and
– electrical installations in extremely low ambient temperatures.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This fourth edition cancels and replaces the third edition published in 2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the document has been completely rewritten. References are, to the extent possible, made to IEC 60079-14 and to other relevant standards, as appropriate, from IEC TC 31; only requirements concerning offshore installations that deviate from the general requirements for installations in hazardous areas are given;
b) requirements as to gas detection have been transferred to an informative annex;
c) requirements concerning emergency shutdown (ignition source control) have been transferred to IEC 61892-1.

  • Standard
    108 pages
    English and French language
    sale 15% off

IEC 61892-2:2019 is applicable to system design of electrical installations and equipment in mobile and fixed offshore units including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or hand-held, to AC installations and DC installations, without any voltage level limitation. Referenced equipment standards may give voltage level limitations.
This document specifies requirements such as those concerning
– sources of electrical power for manned and unmanned units,
– system earthing, both for low-voltage and high-voltage installations,
– interface for electric transmission systems with power supplied from shore, between interconnected offshore units, and with power supplied by offshore units to subsea installations,
– distribution systems,
– cables and wiring systems,
– system studies and calculations,
– protection against electrical faults,
– lighting,
– energy control, monitoring and alarm systems, and
– turret/swivel.
This document gives information and guidance on topics such as
– applicable examples of HVDC VSC technology, and
– guidelines for illumination level.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This third edition cancels and replaces the second edition published in 2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the requirement for sources of electrical power has been rewritten. Requirements both for manned and unmanned units are given. Requirements for essential services of electrical power have been added;
b) the requirement in relation to dead start has been added;
c) the requirement for emergency stop for motor-driven fuel-oil transfer and fuel-oil pressure pumps has been added;
d) general requirements regarding cables and wiring systems have been added;
e) the description of unit interfaces to electrical transmission systems has been included;
f) requirements in relation to energy control, monitoring and alarm system have been rewritten;
g) new clauses regarding swivel/turret and unmanned facilities have been added;
h) informative annexes regarding the following have been added:
– essential source of electrical power;
– emergency source of electrical power;
– applicable examples of HVDC VSC technologies;
– swivel/turret;
– power sources for unmanned units, with separate or combined main and emergency switchboard;
– alternative power sources of electrical power – general requirements;
– illumination level;
– enhanced software simulation;
– architecture for energy control, monitoring and alarm system.

  • Standard
    234 pages
    English and French language
    sale 15% off

IEC 61892-3:2019 is applicable to electrical equipment in mobile and fixed offshore units including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or hand-held, to AC installations and DC installations without any voltage level limitation. Referenced equipment standards may give voltage level limitations.
This document specifies requirements such as those concerning
– enclosures, with regard to material, marking (nameplates and labels), ventilation, earthing, EMC and short-circuit rating of components, and
– specific requirements related to use in an offshore unit, such as
• generators and motors,
• transformers,
• switchgear and control gear assemblies,
• instrumentation of power sources,
• semiconductor converters,
• secondary cells and batteries,
• luminaires,
• communication equipment,
• control and instrumentation, and
• accessories for accommodation and similar areas.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This fourth edition cancels and replaces the third edition published in 2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the previous voltage limitations have been removed;
b) Clause 4 has been completely rewritten, giving general requirements as to relevant electrical equipment;
c) requirements concerning pyrotechnic fault current limiters have been added;
d) requirements as to gas insulated switchgear have been added;
e) the requirement concerning the isolation of supply to galley has been moved to IEC 61892-2;
f) requirements concerning control and instrumentation have been rewritten, based on changes in IEC 61892-2.

  • Standard
    102 pages
    English and French language
    sale 15% off

IEC 61892-6:2019 provides specific requirements for the installation of electrical equipment in mobile and fixed offshore units, including pipeline, pumping or "pigging" stations, compressor stations and single buoy moorings, used in the offshore petroleum industry for drilling, production, accommodation, processing, storage and offloading purposes.
It applies to all installations, whether permanent, temporary, transportable or hand-held, to AC installations and DC installations without any voltage level limitation. Referenced equipment standards may give voltage level limitations.
This document specifies requirements such as those concerning
– protection during equipment storage and in the installation period,
– installation of generators and motors,
– installation of transformers,
– installation of switchgear and controlgear assemblies,
– installation of semiconductor converters and UPS,
– installation of secondary cells and batteries,
– installation of luminaires,
– installation of heating and cooking appliances,
– installation of trace and surface heating,
– installation of cables and wiring, both low-voltage and high-voltage cables,
– requirements in relation to earthing and bonding,
– lightning protection;,
– testing of completed installation, and
– documentation.
This document does not apply to
– fixed equipment for medical purposes,
– electrical installations of tankers, and
– control of ignition sources other than those created by electrical equipment.
This fourth edition cancels and replaces the third edition published in 2013. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) requirements for protection during equipment storage have been added;
b) the special requirements for distribution board enclosures in accommodation spaces have been deleted;
c) requirements for installation of UPS have been updated;
d) requirements regarding the installation of batteries have been modified;
e) requirements for large single-core cables for three-phase AC have been updated;
f) requirements in relation to cable transit systems have been added;
g) the table on the sizes of earth continuity conductors and equipment earthing connections, set out in IEC 61892-4:2007, has been included;
h) requirements as to the installation of controls and instrumentation have been modified; clauses relevant to design and equipment have been deleted.

  • Standard
    95 pages
    English and French language
    sale 15% off

IEC/IEEE 80005-1:2019 describes high-voltage shore connection (HVSC) systems, onboard the ship and on shore, to supply the ship with electrical power from shore. This document is applicable to the design, installation and testing of HVSC systems and addresses: - HV shore distribution systems, - shore-to-ship connection and interface equipment, - transformers/reactors, - semiconductor/rotating frequency convertors, - ship distribution systems, and - control, monitoring, interlocking and power management systems. It does not apply to the electrical power supply during docking periods, for example dry docking and other out of service maintenance and repair. Additional and/or alternative requirements can be imposed by national administrations or the authorities within whose jurisdiction the ship is intended to operate and/or by the owners or authorities responsible for a shore supply or distribution system. It is expected that HVSC systems will have practicable applications for ships requiring 1 MVA or more or ships with HV main supply. Low-voltage shore connection systems are not covered by this document. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) modification of 4.1, Figure 1: transformer on ship is optional, earthing switches on ship removed; b) 4.2.2 and new item 11.3: alternative procedure of periodic testing added; c) modification of 4.9: - minimum current value in the safety circuits shall be 50 mA; - opening of safety loop shall cause the automatic opening of ship and shore HVSC circuit breakers in a maximum time of 200 ms; d) modification of 5.2: added Figure on harmonic contents; e) modification of 6.2.3: – earthing transformer with resistor can be used also on the secondary side; – neutral earthing resistor rating in amperes shall be minimum 25 A, 5 s; f) modification of all annexes: the safety circuits shall be mandatory; g) modification of A.2.1: a metallic shield shall be installed at least on the power cores or common on pilot wires; h) modification of B.7.2.1: new safety circuit introduced: single line diagram and description; i) modification of C.4.1: SLD for cruise ships was updated, also the safety circuits to be coherent with main body, IEC symbols and introduced more details about the control socket-outlets and plugs manufacturer type; j) modification of C.7.3.1: - shore power connector pin assignment is updated; - all cruise ships shall use 4 cables in all cases; k) added D.6.1: the supply point on shore can be fixed or movable; l) modification of D.7.3.2: the voltage used in the pilot circuit for container ships shall be less than 60 V DC or 25 V AC. m) added D.8.6 and D.9.3.1: automatic restart and synchronization alternatives; n) Annex E set to informative; o) Annex F set to informative.

  • Standard
    74 pages
    English language
    sale 15% off

IEC/IEEE 80005-1:2019 is available as IEC/IEEE 80005-1:2019 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC/IEEE 80005-1:2019 describes high-voltage shore connection (HVSC) systems, onboard the ship and on shore, to supply the ship with electrical power from shore. This document is applicable to the design, installation and testing of HVSC systems and addresses:
- HV shore distribution systems,
- shore-to-ship connection and interface equipment,
- transformers/reactors,
- semiconductor/rotating frequency convertors,
- ship distribution systems, and
- control, monitoring, interlocking and power management systems.
It does not apply to the electrical power supply during docking periods, for example dry docking and other out of service maintenance and repair. Additional and/or alternative requirements can be imposed by national administrations or the authorities within whose jurisdiction the ship is intended to operate and/or by the owners or authorities responsible for a shore supply or distribution system. It is expected that HVSC systems will have practicable applications for ships requiring 1 MVA or more or ships with HV main supply. Low-voltage shore connection systems are not covered by this document. This second edition cancels and replaces the first edition published in 2012. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) modification of 4.1, Figure 1: transformer on ship is optional, earthing switches on ship removed;
b) 4.2.2 and new item 11.3: alternative procedure of periodic testing added;
c) modification of 4.9:
- minimum current value in the safety circuits shall be 50 mA;
- opening of safety loop shall cause the automatic opening of ship and shore HVSC circuit breakers in a maximum time of 200 ms;
d) modification of 5.2: added Figure on harmonic contents;
e) modification of 6.2.3:
– earthing transformer with resistor can be used also on the secondary side;
– neutral earthing resistor rating in amperes shall be minimum 25 A, 5 s;
f) modification of all annexes: the safety circuits shall be mandatory;
g) modification of A.2.1: a metallic shield shall be installed at least on the power cores or common on pilot wires;
h) modification of B.7.2.1: new safety circuit introduced: single line diagram and description;
i) modification of C.4.1: SLD for cruise ships was updated, also the safety circuits to be coherent with main body, IEC symbols and introduced more details about the control socket-outlets and plugs manufacturer type;
j) modification of C.7.3.1:
- shore power connector pin assignment is updated;
- all cruise ships shall use 4 cables in all cases;
k) added D.6.1: the supply point on shore can be fixed or movable;
l) modification of D.7.3.2: the voltage used in the pilot circuit for container ships shall be less than 60 V DC or 25 V AC.
m) added D.8.6 and D.9.3.1: automatic restart and synchronization alternatives;
n) Annex E set to informative;
o) Annex F set to informative.

  • Standard
    74 pages
    English language
    sale 15% off

IEC 60092-101:2018 is applicable to electrical installations for use in ships.
The 60092 series form a code of practical interpretation and amplification of the requirements of the International Convention for the Safety of Life at Sea, a guide for future regulations which may be prepared and a statement of practice for use by ship-owners, shipbuilders and appropriate organizations.
This fifth edition cancels and replaces the fourth edition published in 1994 and Amendment 1:1995. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) the applicability of the standard has been changed to 1 000 V AC and 1 500 V DC:
b) the table for design temperature has been simplified;
c) the clause regarding power supply system characteristics has been rewritten;
d) information regarding pollution degree has been added in the clause regarding clearance and creepage distances;
e) a clause regarding environmental impact has been added;
f) the clause regarding classification test for materials has been deleted;
g) the annex regarding flame-retardant test for cables has been deleted;
h) the annex regarding test on bunched wires or cables under fire conditions has been deleted.

  • Standard
    31 pages
    English language
    sale 15% off

This International Standard specifies requirements and gives guidelines for the placement, installation
and visibility of navigation lights as described in COLREG for recreational craft of less than 24 m in
length of hull, as described in ISO 8666. Annex A lists additional information to be included in the
owner’s manual.
NOTE Other national regulations may apply for craft on certain waters.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60601-2-76:2018 applies to the basic safety and essential performance of low energy ionized gas haemostasis equipment.
Hazards inherent in the intended physiological function of ME Equipment or ME Systems within the scope of this document are not covered by specific requirements in this document except in 7.2.13 and 8.4.1 of the general standard.
This particular standard amends and supplements IEC 60601-1:2005 and IEC 60601-1:2005/AMD1:2012.

  • Standard
    53 pages
    English and French language
    sale 15% off

IEC 63010-1:2017(E) applies to cables with insulation and sheaths based on halogen-free thermoplastic compounds for use with small devices and for short connections to desktop electrical appliances where flexibility is of prime importance. These cables have a voltage rating U0/U up to and including 300/300 V. Maximum operating temperature for the cables in this document is 70°C.

  • Standard
    23 pages
    English language
    sale 15% off

Describes test methods and requirements for the design of electrical devices to be used on small craft so that they may be operated in an explosive atmosphere without igniting surrounding flammable gases.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC PAS 63108:2017 specifies the requirements of primary DC distribution systems and interconnected installations.
The requirements of this PAS establish general principles for
- operations, without degrading unit and human safety, capable of a reduced environmental footprint,
- existing and new power generating units, new DC distribution concepts for electrical power, energy storage and advanced control of a total power balance, including semiconductor converters (AC to DC, DC to DC and DC to AC power converters) and dynamic load controllers, and
- relevant system studies and calculations demonstrating a protection philosophy as needed for necessary selectivity, segregation methods and equipment.
This PAS also gives guidelines for integration of energy sources of different nature and suitable ways to identify locations of such installations.

  • Technical specification
    20 pages
    English language
    sale 15% off

IEC 60092-376:2017 is available as IEC 60092-376:2017 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-376:2017 is applicable to screened and unscreened cables for control and instrumentation circuits on ships and offshore units. The cables have extruded solid insulation with a voltage rating of 150/250V (300V) and are intended for fixed installations.
The various types of cables are given in Clause 5. The constructional requirements and test methods are aligned with those indicated in IEC 60092-350, unless otherwise specified in this document.
The object of this document is:
- to standardise cables whose safety and reliability are ensured when they are installed in accordance with the requirements of IEC 60092-352,
- to lay down standard manufacturing requirements and characteristics of such cables directly or indirectly bearing on safety, and
- to specify test methods for checking conformity with those requirements.
This edition includes the following significant technical changes with respect to the previous edition:
- new structure in line with IEC 60092-353 and IEC 60092-354;
- requirements and test methods have been divided in several tables for clarification (enhanced cold properties, oil resistance or resistance to drilling fluids) and have been aligned to IEC 60092-350;
- the new testing methods for fire resistant cables are referenced in this document.

  • Standard
    24 pages
    English language
    sale 15% off

IEC 60317-70:2017 specifies requirements of polyester glass-fibre wound fused, unvarnished or resin or varnish impregnated, bare or grade 1 or grade 2 enamelled round copper winding wires, temperature index 155. The impregnating agent can be, for instance, epoxy, polyester, or polyesterimide resin based. NOTE - For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requirements for temperature index and heat shock temperature cannot be specified.
Keywords: insulated wires used for windings

  • Standard
    20 pages
    English and French language
    sale 15% off

This European Standard specifies requirements relating to devices for the supply of electrical power (three-phase AC - 400 V, with a frequency of 50 Hz and with a current of at least 250 A) to vessels in port.
Annex A to this European Standard stipulates general and safety-technical requirements relating to the shore-based section of the electrical shore connection.
Annex B to this European Standard stipulates general and safety-technical requirements relating to the connecting cables and to the on-board section of the electrical shore connection.
The requirements according to the HD 60364 and HD 384 series of standards generally apply to shore-based low-voltage equipment. The requirements of Annex A of this European Standard complement the requirements contained in HD 60364/HD 384 Parts 1 to 6.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements relating to electrical installations for the supply of electrical power (three-phase AC - 400 V, 50 Hz and with a rated current of at least 250 A) to vessels in port.
Annex A stipulates general and safety requirements relating to the shore-based section of the electrical shore connection.
Annex B stipulates general and safety requirements relating to the shore-based connecting cables and to the on-board section of the electrical shore connection.
Annex C contains information concerning the dimensioning of shore-based connecting cables.
The requirements according to the HD 60364 and HD 384 series of standards generally apply to shore-based low-voltage equipment.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 62586-2:2017 specifies functional tests and uncertainty requirements for instruments whose functions include measuring, recording, and possibly monitoring power quality parameters in power supply systems, and whose measuring methods (class A or class S) are defined in IEC 61000-4-30.
This document applies to power quality instruments complying with IEC 62586-1.
This document can also be referred to by other product standards (e.g. digital fault recorders, revenue meters, MV or HV protection relays) specifying devices embedding class A or class S power quality functions according to IEC 61000-4-30.
These requirements are applicable in single-, dual- (split phase) and 3-phase AC power supply systems at 50 Hz or 60 Hz.
This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- test procedures for RVC and current have been added;
- mistakes have been fixed.
The contents of the corrigendum of June 2018 have been included in this copy.

  • Standard
    290 pages
    English and French language
    sale 15% off

IEC 60092-504:2016 is available as IEC 60092-504:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-504:2016 specifies electrical, electronic and programmable equipment intended for automation, control, monitoring, alert, and safety and protection systems for use in ships. This edition includes the following significant technical changes with respect to the previous edition:
a) the part title has been changed, the term "Automation" was added;
b) the contents of the corrigendum of January 2011 have been included;
c) a new subclause 5.1 "General" with general requirements for type testing has been added;
d) Table 1 contents aligned with current version of document IACS Req. 1991/Rev. 5, 2006;
e) the revised IMO Resolution A.1021(26), Code on alerts and indicators:2009 has been taken into account;
f) IMO Resolution MSC.302(87) has been taken into account. As a consequence, the term "alert" has been used where the generic term applies. This concerns, in particular, the text in 8.4 and 9.3;
g) a new subclause 8.2.4: The revised IMO Resolution MSC.145(77), Performance standards for water level detectors on bulk carriers:2003 has been taken into account;
h) subclause 9.1 about fire detection and alarm systems has been completely revised, IMO Resolution MSC.98(73) (FSS Code) with amendment MSC.292(87): 2010 has been taken into account;
i) a new subclause 9.2 "Bilge systems" has been added;
j) the subclauses 9.4 "Automatic control installations for electrical power supply" and 9.5 "Automatic starting installations for electrical motor-driven auxiliaries" have been completely revised;
k) Clause 10 "Computer based systems" has been completely revised;
l) a new subclause 10.3.6 about wireless data communication has been added;
m) a new subclause 10.5 about remote access has been added.

  • Standard
    116 pages
    English and French language
    sale 15% off

IEC 60092-353:2016 is available as IEC 60092-353:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-353:2016 is applicable to shipboard and offshore non radial field power cables with extruded solid insulation, having a voltage rating of 0,6/1 (1,2) kV or 1,8/3 (3,6) kV intended for fixed installations. Cables designed to maintain circuit integrity during fire are included. The various types of power cables are given in 5.1. The constructional requirements and test methods are aligned with those indicated in IEC 60092-350, unless otherwise specified in this document. The object of this document is:
- to standardize cables whose safety and reliability is ensured when they are installed in accordance with the requirements of IEC 60092-352 or IEC 61892-4,
- to lay down standard manufacturing requirements and characteristics of such cables directly or indirectly bearing on safety, and
- to specify test methods for checking conformity with those requirements. This edition includes the following significant technical changes with respect to the previous edition:
- updated references to IEC 60092-350 for general construction and test methods and IEC 60092-360 for insulating and sheathing materials.

  • Standard
    41 pages
    English and French language
    sale 15% off

IEC 60092-202:2016 is available as IEC 60092-202:2016 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60092-202:2016 is applicable to the main features of the electrical protective system to be applied to electrical installations for use in ships. This fifth edition cancels and replaces the fourth edition published in 1994 and Amendment 1:1996. This edition constitutes a full technical revision.

  • Standard
    39 pages
    English and French language
    sale 15% off

IEC/IEEE 80005-2:2016 describes the data interfaces of shore and ships as well as step by step procedures for low and high voltage shore connection systems communication for non-emergency functions, where required. This standard specifies the interface descriptions, addresses and data type. This standard also specifies communication requirements on cruise ships, in annex A. Application of this standard relates to annexes of IEC/ISO/IEEE 80005-1. This standard does not specify communication for emergency functions as described in IEC/ISO/IEEE 80005-1.

  • Standard
    111 pages
    English and French language
    sale 15% off

This International Standard addresses the design and installation of alternating current (AC) and direct current (DC) electrical systems used for the purpose of electrical propulsion and/or electrical hybrid (system with both a rechargeable battery and a fuelled power source) propulsion.
This International Standard applies to electrical propulsion systems operated in the following ranges either individually or in combination:
— direct current of less than 1 500 V DC;
— single-phase alternating current up to AC 1 000 V;
— three-phase alternating current up to AC 1 000 V.
This International Standard applies to electrical propulsion systems installed in small craft up to 24 m length of the hull (LH according to ISO 8666).
This International Standard also lists in Annex A additional information to be included in the owner’s manual as well as Annex B additional information to be provided to the installer.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 16315:2016 addresses the design and installation of alternating current (AC) and direct current (DC) electrical systems used for the purpose of electrical propulsion and/or electrical hybrid (system with both a rechargeable battery and a fuelled power source) propulsion.
ISO 16315:2016 applies to electrical propulsion systems operated in the following ranges either individually or in combination: direct current of less than 1 500 V DC; single-phase alternating current up to AC 1 000 V; three-phase alternating current up to AC 1 000 V.
ISO 16315:2016 applies to electrical propulsion systems installed in small craft up to 24 m length of the hull (LH according to ISO 8666).

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This International Standard applies to requirements and testing for navigation lights with permanently
fixed light emitting diode (LED) assemblies for small craft up to 24 m length of the hull.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

ISO 19009:2015 applies to requirements and testing for navigation lights with permanently fixed light emitting diode (LED) assemblies for small craft up to 24 m length of the hull.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

The particular requirements specified in this part of HD 60364 apply to onshore installations dedicated to
supply inland navigation vessels for commercial and administrative purpose, berthed in ports and berths.
For single- and three-phase supplies to pleasure craft, use HD 60364-7-709.
This part of HD 60364 applies to installations with nominal supply voltage a.c. 400/230 V, single-phase and
three-phase, 50 Hz.
Additional requirements that do not relate to electrical installation are given in EN 15869-1 and EN 15869-2.
The particular requirements do not apply to the onboard installations of inland navigation vessels including
their connection cables. Additional requirements on the onboard installation are given in EN 15869-3.

  • Standardization document
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

IEC 60533:2015 is available as IEC 60533:2015 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 60533:2015(E) specifies minimum requirements for emission, immunity and performance criteria regarding electromagnetic compatibility (EMC) of electrical and electronic equipment for ships with metallic hull. This International Standard assists in meeting the relevant EMC requirements as stated in SOLAS 74, Chapter IV, Regulation 6 and Cha pter V, Regulation 17. Reference to this International Standard is made in IMO Resolution A.813(19). This edition includes the followi ng significant technical changes with respect to the previous edition:
- Introduction has been supplemented;
- scope and title have been modified to limit the application of the standard to installations in ships with metallic hulls only;
- the normative references have been updated;
- further explanation for in-situ testing has been given in 5.1;
- numbering of CISPR-Standards in Tables 1, 2 and 3 has been updated;
- title of Annex B has been changed;
- requirements on cable routing in Annex B have been amended;
- new Annex C EMC test report has been added.

  • Standard
    56 pages
    English language
    sale 15% off

The particular requirements specified in this part of HD 60364 apply to onshore installations dedicated to supply inland navigation vessels for commercial and administrative purpose, berthed in ports and berths. For single- and three-phase supplies to pleasure craft, use HD 60364-7-709. This part of HD 60364 applies to installations with nominal supply voltage a.c. 400/230 V, single-phase and three-phase, 50 Hz. Additional requirements that do not relate to electrical installation are given in EN 15869-1 and EN 15869-2. The particular requirements do not apply to the onboard installations of inland navigation vessels including their connection cables. Additional requirements on the onboard installation are given in EN 15869-3.

  • Standardization document
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day