Terms and definitions used in connection with reference materials — Amendment 1: Revision of definitions for reference material and certified reference material

Termes et définitions utilisés en rapport avec les matériaux de référence — Amendement 1: Révision des définitions de matériau de référence et de matériau de référence certifié

General Information

Status
Withdrawn
Publication Date
16-Nov-2008
Withdrawal Date
16-Nov-2008
Current Stage
9599 - Withdrawal of International Standard
Completion Date
06-Feb-2015
Ref Project

Relations

Buy Standard

Guide
ISO Guide 30:1992/Amd 1:2008 - Revision of definitions for reference material and certified reference material
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
Guide
ISO Guide 30:1992/Amd 1:2008 - Révision des définitions de matériau de référence et de matériau de référence certifié
French language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

GUIDE 30/Amd. 1

Terms and definitions used in
connection with reference
materials
Amendment 1
Revision of definitions for
reference material and certified
reference material



Second edition 1992
AMENDMENT 1 2008
©
 ISO 2008

---------------------- Page: 1 ----------------------
ISO GUIDE 30:1992(E)/Amd.1:2008
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2008
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland


ii © ISO 2008 – All rights reserved

---------------------- Page: 2 ----------------------
ISO GUIDE 30:1992(E)/Amd.1:2008
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
Draft Guides adopted by the responsible Committee or Group are circulated to the member bodies for voting.
Publication as a Guide requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO Guide 30:1992 was prepared by the ISO Committee on reference materials (REMCO).


© ISO 2008 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO GUIDE 30:1992(E)/Amd.1:2008

Terms and definitions used in connect
...

GUIDE 30/Amd.1

Termes et définitions utilisés en
rapport avec les matériaux de
référence
Amendement 1
Révision des définitions de
matériau de référence et de
matériau de référence certifié



Deuxième édition 1992
AMENDEMENT 1 2008
©
 ISO 2008

---------------------- Page: 1 ----------------------
GUIDE ISO 30:1992(F)/Amd.1:2008
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.


DOCUMENT PROTÉGÉ PAR COPYRIGHT


©  ISO 2008
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse


ii © ISO 2008 – Tous droits réservés

---------------------- Page: 2 ----------------------
GUIDE ISO 30:1992(F)/Amd.1:2008
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiée
aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du
comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 2.
Les projets de Guides adoptés par le comité ou le groupe responsable sont soumis aux comités membres
pour vote. Leur publication comme Guides requiert l'approbation de 75 % au moins des comités membres
votants.
L'attention est appelée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable de ne
pas avoir identifié de tels droits de propriété et averti de leur existence.
L'Amendement 1 au Guide ISO 30:1992 a été élaboré par le Comité pour les matériaux de référence
(REMCO) de l'ISO.


© ISO 2008 – Tous droits réservés iii

---------------------- Page: 3 -----------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.