ISO 16063-21:2003/Amd 1:2016

Methods for the calibration of vibration and shock transducers — Part 21: Vibration calibration by comparison to a reference transducer — Amendment 1

Méthodes pour l'étalonnage des transducteurs de vibrations et de chocs — Partie 21: Étalonnage de vibrations par comparaison à un transducteur de référence — Amendement 1

General Information

• Status: Published
• Publication Date: 01-Feb-2016
• ICS: 17.160 - Vibrations, shock and vibration measurements
• Technical Committee: ISO/TC 108 - Mechanical vibration, shock and condition monitoring
• Drafting Committee: ISO/TC 108/WG 34 - Calibration of vibration and shock transducers
• Current Stage: 6060 - International Standard published
• Due Date: 04-Feb-2018
• Completion Date: 02-Feb-2016

Relations

• Amends: ISO 16063-21:2003 - Methods for the calibration of vibration and shock transducers — Part 21: Vibration calibration by comparison to a reference transducer
• Effective Date: 21-Aug-2021

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 16063-21
First edition
2003-08-15
AMENDMENT 1
2016-02-01
Methods for the calibration of
vibration and shock transducers —
Part 21:
Vibration calibration by comparison
to a reference transducer
AMENDMENT 1
Méthodes pour l’étalonnage des transducteurs de vibrations et de
chocs —
Partie 21: Étalonnage de vibrations par comparaison à un
transducteur de référence
AMENDEMENT 1
Reference number
ISO 16063-21:2003/Amd.1:2016(E)
©
ISO 2016

---------------------- Page: 1 ----------------------
ISO 16063-21:2003/Amd.1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16063-21:2003/Amd.1:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this do
...

DRAFT AMENDMENT
ISO 16063-21:2003/DAM 1
ISO/TC 108/SC 3 Secretariat: DS
Voting begins on: Voting terminates on:
2015-05-11 2015-08-11
Methods for the calibration of vibration and shock
transducers —
Part 21:
Vibration calibration by comparison to a reference
transducer
AMENDMENT 1
Méthodes pour l’étalonnage des transducteurs de vibrations et de chocs —
Partie 21: Étalonnage de vibrations par comparaison à un transducteur de référence
AMENDEMENT 1
ICS: 17.160
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 16063-21:2003/DAM 1:2015(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2015

---------------------- Page: 1 ----------------------
ISO 16063-21:2003/DAM 1:2015(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 16063-21:2003 DAmd. 1
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national
standards bodies (ISO member bodies). The work of preparing International Standards is normally
carried out through ISO technical committees. Each member body interested in a subject for which a
technical committee has been established has the right to be represented on that committee.
International organizations, governmental and non-governmental, in liaison with ISO, also take part in
the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all
matters of electrotechnical standardization.
The procedures used to develop this document and those inte
...