ISO 6187:2001
(Main)Rigid cellular plastics — Determination of friability
Rigid cellular plastics — Determination of friability
This International Standard specifies a method for the determination of the mass loss of rigid cellular plastics as a result of a combination of abrasion and impact produced by a laboratory tumbling mechanism.
Plastiques alvéolaires rigides — Détermination de la friabilité
General Information
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 6187
First edition
2001-09-15
Rigid cellular plastics — Determination of
friability
Plastiques alvéolaires rigides — Détermination de la friabilité
Reference number
ISO 6187:2001(E)
© ISO 2001
---------------------- Page: 1 ----------------------
ISO 6187:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2001 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6187:2001(E)
Contents Page
1 Scope . 1
2 Normative reference . 1
3 Terms and definitions . 1
4 Apparatus . 1
5 Test specimens . 2
6 Procedure . 2
7 Calculation . 2
8 Precision and bias . 3
9 Test report . 3
Bibliography. 4
©
ISO 2001 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6187:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 6187 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 10,
Cellular plastics.
©
iv ISO 2001 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6187:2001(E)
Rigid cellular plastics — Determination of friability
WARNING — This International Standard does not purport to address all of the safety concerns, if any,
associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and
health practices and determine the applicability of regulatory limitations prior to use.
1 Scope
This International Standard specifies a method for the determination of the mass loss of rigid cellular plastics as a
result of a combination of abrasion and impact produced by a laboratory tumbling mechanism.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent edition of the normative document indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 845:1988, Cellular plastics and rubbers — Determination of apparent (bulk) density.
3 Terms and definitions
For the purposes of this International Standard, the following terms and definitions apply.
3.1
cellular plastic
a plastic whose density is reduced by the presence of numerous small cavities (cells), intercon
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.