Dentistry — Handpieces and motors

ISO 14457:2012 is applicable to handpieces and motors used in dentistry for patient contact, regardless of their construction. It specifies requirements, test methods, manufacturer's information, marking and packaging. ISO 14457:2012 is applicable to: straight and geared angle handpieces, including handpiece attachments; high-speed air turbine handpieces; air motors; electrical motors; prophy handpieces.

Médecine bucco-dentaire — Pièces à main et moteurs

L'ISO 14457:2012 s'applique aux pièces à main et aux moteurs utilisés en médecine bucco-dentaire pour le contact patient, quelle que soit leur construction. Elle spécifie les exigences, les méthodes d'essai, les informations du fabricant, le marquage et l'emballage. L'ISO 14457:2012 s'applique aux pièces à main rectilignes et à contre-angles, y compris aux raccordements de la pièce à main, aux pièces à main à turbines à air comprimé pour grandes vitesses, aux moteurs à air, aux moteurs électriques, et aux pièces de prophylaxie.

General Information

Status
Withdrawn
Publication Date
10-Sep-2012
Withdrawal Date
10-Sep-2012
Current Stage
9599 - Withdrawal of International Standard
Completion Date
17-Oct-2017
Ref Project

Relations

Buy Standard

Standard
ISO 14457:2012 - Dentistry -- Handpieces and motors
English language
22 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 14457:2012 - Médecine bucco-dentaire -- Pieces a main et moteurs
French language
21 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 14457
First edition
2012-09-15
Dentistry — Handpieces and motors
Médecine bucco-dentaire — Pièces à main et moteurs
Reference number
ISO 14457:2012(E)
ISO 2012
---------------------- Page: 1 ----------------------
ISO 14457:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,

electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s

member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 14457:2012(E)
Contents Page

Foreword ............................................................................................................................................................................. v

Introduction .......................................................................................................................................................................vi

1 Scope ...................................................................................................................................................................... 1

2 Normative references ......................................................................................................................................... 1

3 Terms and definitions ......................................................................................................................................... 2

4 Classification of handpieces ............................................................................................................................ 4

5 Requirements and performance ...................................................................................................................... 4

5.1 General ................................................................................................................................................................... 4

5.2 Materials ................................................................................................................................................................. 4

5.3 Drop test ................................................................................................................................................................ 4

5.4 Noise level ............................................................................................................................................................. 4

5.5 Surfaces ................................................................................................................................................................. 4

5.6 Power supply ........................................................................................................................................................ 5

5.7 Air and water pressure ....................................................................................................................................... 6

5.8 Temperature .......................................................................................................................................................... 6

5.9 Vibrations .............................................................................................................................................................. 6

5.10 Resistance to reprocessing .............................................................................................................................. 6

5.11 Leakage and/or ingress of water ..................................................................................................................... 6

5.12 Electromagnetic compatibility ......................................................................................................................... 6

5.13 Operating controls .............................................................................................................................................. 6

5.14 Usability ................................................................................................................................................................. 7

5.15 Connection and supply ...................................................................................................................................... 7

5.16 Chuck system for shanks ................................................................................................................................. 9

5.17 Test mandrel ......................................................................................................................................................... 9

5.18 Speed .................................................................................................................................................................... 11

5.19 Eccentricity ......................................................................................................................................................... 11

5.20 Torque ................................................................................................................................................................... 11

5.21 Dimensions of head and nose ....................................................................................................................... 11

6 Sampling ..............................................................................................................................................................12

7 Testing ..................................................................................................................................................................12

7.1 General test conditions ...................................................................................................................................12

7.2 Visual inspection ...............................................................................................................................................13

7.3 Power supply — Electrical ..............................................................................................................................13

7.4 Power supply — Air ..........................................................................................................................................13

7.5 Spray air supply .................................................................................................................................................13

7.6 Spray water supply ...........................................................................................................................................13

7.7 Air and water pressure .....................................................................................................................................14

7.8 Motor cooling air ...............................................................................................................................................14

7.9 Connector for handpiece attachment and for air-powered handpiece ...............................................14

7.10 Connection and supply ....................................................................................................................................14

7.11 Test mandrels .....................................................................................................................................................14

7.12 Chuck for shanks ..............................................................................................................................................15

7.13 Dimensions (of head and nose) .....................................................................................................................15

7.14 Eccentricity .........................................................................................................................................................16

7.15 Torque ...................................................................................................................................................................16

7.16 Noise level ...........................................................................................................................................................16

7.17 Speed ....................................................................................................................................................................17

7.18 Temperature rise of housing ..........................................................................................................................17

7.19 Temperature, excessive ...................................................................................................................................17

7.20 Resistance to reprocessing ............................................................................................................................17

8 Instructions for use, maintenance and service .........................................................................................17

© ISO 2012 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 14457:2012(E)

9 Technical description .......................................................................................................................................18

10 Marking .................................................................................................................................................................18

10.1 General .................................................................................................................................................................18

10.2 Handpieces .........................................................................................................................................................18

10.3 Motors ...................................................................................................................................................................18

11 Labelling ..............................................................................................................................................................19

12 Packaging ............................................................................................................................................................19

Annex A (informative) Handpiece categories ............................................................................................................20

Bibliography .....................................................................................................................................................................22

iv © ISO 2012 – All rights reserved
---------------------- Page: 4 ----------------------
ISO 14457:2012(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies

(ISO member bodies). The work of preparing International Standards is normally carried out through ISO

technical committees. Each member body interested in a subject for which a technical committee has been

established has the right to be represented on that committee. International organizations, governmental and

non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International

Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.

International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standards

adopted by the technical committees are circulated to the member bodies for voting. Publication as an

International Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

rights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 14457 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 4, Dental instruments.

ISO 14457 cancels and replaces ISO 7785-1:1997, ISO 7785-2:1995, ISO 11498:1997 and ISO 13294:1997,

which have been technically revised.
© ISO 2012 – All rights reserved v
---------------------- Page: 5 ----------------------
ISO 14457:2012(E)
Introduction

Dental handpieces and dental motors have been used in dental treatment procedures for many years.

Technical development creates handpieces and motors that are better and easier to use. The combination of

these items is very important for good performance.

This International Standard combines the content of the following four ISO standards, which have now

been withdrawn.
ISO 7785-1:1997, Dental handpieces — Part 1: High-speed air turbine handpieces

ISO 7785-2:1995, Dental handpieces — Part 2: Straight and geared angle handpieces

ISO 11498:1997, Dental handpieces — Dental low-voltage electrical motors
ISO 13294:1997, Dental handpieces — Dental air-motors
vi © ISO 2012 – All rights reserved
---------------------- Page: 6 ----------------------
INTERNATIONAL STANDARD ISO 14457:2012(E)
Dentistry — Handpieces and motors
1 Scope

This International Standard is applicable to handpieces and motors used in dentistry for patient contact,

regardless of their construction. It specifies requirements, test methods, manufacturer’s information, marking

and packaging.
This International Standard is applicable to:
a) straight and geared-angle handpieces, including handpiece attachments;
b) high-speed air turbine handpieces;
c) air motors;
d) electrical motors;
e) prophy handpieces.
This International Standard is not applicable to:
1) intraoral camera handpieces;
2) powered polymerization handpieces;
3) air-powered scalers;
4) electrical powered scalers;
5) air-powder polishing handpieces;
6) multifunction handpieces (syringes).

NOTE See Annex A for clarification of the handpieces, attachments and motor types covered by this International Standard.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated

references, only the edition cited applies. For undated references, the latest edition of the referenced document

(including any amendments) applies.

ISO 1797-1, Dentistry — Shanks for rotary instruments — Part 1: Shanks made of metals

ISO 1797-2, Dental rotary instruments — Shanks — Part 2: Shanks made of plastics
ISO 1942, Dentistry — Vocabulary
ISO 3964, Dental handpieces — Coupling dimensions

ISO 5349-1, Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted

vibration — Part 1: General requirements

ISO 5349-2, Mechanical vibration — Measurement and evaluation of human exposure to hand-transmitted

vibration — Part 2: Practical guidance for measurement at the workplace
ISO 6507-1, Metallic materials — Vickers hardness test — Part 1: Test method

ISO 7405, Dentistry — Evaluation of biocompatibility of medical devices used in dentistry

© ISO 2012 – All rights reserved 1
---------------------- Page: 7 ----------------------
ISO 14457:2012(E)

ISO 7494-1, Dentistry — Dental units— Part 1: General requirements and test methods

ISO 9168, Dentistry — Hose connectors for air driven dental handpieces
ISO 9687, Dental equipment — Graphical symbols

ISO 10993-1, Biological evaluation of medical devices — Part 1: Evaluation and testing within a risk

management process
ISO 13295, Dentistry — Mandrels for rotary instruments

ISO 15223-1, Medical devices — Symbols to be used with medical device labels, labelling and information to

be supplied — Part 1: General requirements

ISO 17664, Sterilization of medical devices — Information to be provided by the manufacturer for the processing

of resterilizable medical devices
ISO 21531, Dentistry — Graphical symbols for dental instruments

IEC 60601-1:2005, Medical electrical equipment — Part 1: General requirements for basic safety and

essential performance
IEC 61672-1, Electroacoustics — Sound level meters — Part 1: Specifications

IEC 62366, Medical devices — Application of usability engineering to medical devices

IEC 80601-2-60:2012, Medical electrical equipment — Part 2-60: Particular requirements for basic safety and

essential performance of dental equipment
3 Terms and definitions

For the purposes of this document, the terms and definitions given in ISO 1942 and the following apply.

3.1
air motor
motor powered by compressed air, which is supplied by a dental unit
3.2
air-powered powder jet handpiece
handpiece powered by air, designed to transfer powder to the patient
3.3
air-powered scaler
handpiece powered by air, with an oscillating working part
3.4
angle handpiece

handpiece with an angle between the input and output axes, driven by an air motor or an electrical motor or

with an internal power supply
3.5
contra-angle handpiece

angle handpiece with one or more additional angles placed so as to bring the working part of the instrument or

tool approximately into line with the main axis of the handpiece
3.6
non-metallic chuck

handpiece chuck with non-metallic material on the contact surface of the shank holding mechanism

3.7
electrical motor
motor powered by electrical energy, which is supplied by a dental unit
2 © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
ISO 14457:2012(E)
3.8
electrical powered scaler
handpiece powered by electrical energy, with an oscillating working part
3.9
working part
part of a fixed or interchangeable instrument connected to a handpiece
3.10
handpiece

powered handheld instrument used to operate a rotary, oscillating or reciprocating working part

3.11
handpiece attachment
extension part of a handpiece designed to hold a working part
3.12
handpiece chuck
part of the handpiece designed to securely hold the shank of a working part
3.13
high-speed air turbine handpiece

handpiece propelled by a small air-powered turbine (or rotor), capable of high speed, which is integrated into

the head of the handpiece and has a chucking device coaxial with the turbine
3.14
intraoral camera handpiece
handpiece designed to take optical images in the oral cavity of the patient
3.15
motor

device, powered by air or electricity supplied by a dental unit, designed to transform energy into movement

3.16
polymerization handpiece

handpiece producing light that is applied directly to polymerizable dental materials in the oral cavity of a patient

3.17
prophy handpiece

angle handpiece used for dental prophylaxis, driven by an air motor or an electrical motor

3.18
rotary instrument

rotating instrument used in a high-speed air turbine handpiece or in a straight and geared-angle handpiece,

consisting of a shank and a working end used for dental procedures
3.19
reciprocating instrument

oscillating instrument used in a high-speed air turbine handpiece, or in a straight and geared-angle handpiece,

consisting of a shank and a working end used for dental procedures
3.20
straight handpiece

handpiece with the input and output axes in alignment, driven by an air motor or an electrical motor or with an

internal power supply
3.21
transmission part

small tool (rotary or reciprocating) designed to transmit energy from the shank to the working end

© ISO 2012 – All rights reserved 3
---------------------- Page: 9 ----------------------
ISO 14457:2012(E)
3.22
working end

distal end of a rotary or oscillating instrument intended for direct use in the oral cavity of the patient

4 Classification of handpieces

Handpieces are classified according to their gear ratio into three types as given in Table 1.

Table 1 — Gear ratios for handpieces
Type Gear ratio Resulting rotating speed Resulting torque Colour
1 >1:1 lower higher green
2 1:1 constant constant blue
3 1:>1 higher lower red
5 Requirements and performance
5.1 General

The construction of handpieces shall provide for their safe and reliable operation. Their use and manipulation

shall be easy and comfortable for the operator. These requirements shall be compliant with IEC 62366.

If field-repairable, the handpieces shall be capable of being easily disassembled and reassembled for

maintenance and repair utilizing either readily available tools or special tools supplied by the manufacturer.

Electrical requirements are only applicable to electrically powered handpieces.
5.2 Materials
Tests for biocompatibility shall be in accordance with ISO 7405 and ISO 10993-1.
5.3 Drop test
IEC 60601-1:2005, 15.3.4.1, applies.
5.4 Noise level

The A-weighted sound pressure value generated by the handpiece shall not exceed 80 dB.

Test in accordance with 7.16.

NOTE This test applies to each handpiece as a system in actual use, i.e. each attachment used with its respective

drive motor.
5.5 Surfaces

Particular attention should be given to providing secure gripping surfaces for operator manipulation under

normal conditions of use.
Test in accordance with IEC 62366.
NOTE In order to reduce glare, highly polished surfaces should be avoided.
4 © ISO 2012 – All rights reserved
---------------------- Page: 10 ----------------------
ISO 14457:2012(E)
5.6 Power supply
5.6.1 Electrical power supply
The following requirements are applicable for:
a) electrical motors;
b) handpieces, integrated with the motor;
c) prophy handpieces, integrated with the motor.

The requirements shall be specified by the manufacturer and shall comply with ISO 7494-1.

Test in accordance with 7.3.
5.6.2 Air supply
5.6.2.1 Air-powered handpiece
The following requirements are applicable for:
a) high-speed air turbine handpieces;
b) air motors;
c) handpieces, integrated with the air motor;
d) prophy handpieces, integrated with the air motor.

Air-powered handpieces shall be operated by a pressurized air supply in accordance with the manufacturer’s

instructions. The necessary flow rate shall be < 66 Nl/min in a pressure range of (300 ± 100) kPa [(3,0 ±1,0) bar].

Test in accordance with 7.4.
5.6.2.2 Motor cooling air
The following requirement is applicable for electrical motors.

If the electrical motor is equipped with an air cooling system, the maximum air flow rate should not be more

than 40 Nl/min and the pressure range should be 250 kPa to 500 kPa (2,5 bar to 5,0 bar). The electrical motor

should have an outlet connection for motor air cooling.
Test in accordance with 7.8.
5.6.2.3 Spray air supply

Spray air coolant capability may be provided at the discretion of the manufacturer. Handpieces having spray

air coolant capability shall direct air to the operating area of the rotary instrument. If water and air are used

simultaneously, a cooling mist shall be created and transmitted to the cutting area of a rotary instrument. The

handpiece shall be capable of attaining an air flow rate of at least 1,5 Nl/min at 200 kPa (2,0 bar).

Motors shall be equipped, if applicable, to transmit air to a handpiece attachment. The equipment shall be

capable of attaining an air flow rate of at least 1,5 Nl/min at 200 kPa (2,0 bar).

Test in accordance with 7.5.
5.6.3 Water supply

The handpiece, if applicable, shall provide a water coolant capability to the operating area of the working part

at a flow rate of at least 50 ml/min at 250 kPa (2,5 bar).
© ISO 2012 – All rights reserved 5
---------------------- Page: 11 ----------------------
ISO 14457:2012(E)
Test in accordance with 7.6.
5.7 Air and water pressure

Applicable motors and handpieces shall remain intact, i.e. shall not rupture or burst, when subjected to a

pressure 50 % above the manufacturer’s maximum recommended operating pressure.
Test in accordance with 7.7.
5.8 Temperature
5.8.1 Temperature rise of housing
IEC 80601-2-60:2012, 201.11.1.1, applies.
Test in accordance with 7.18.
5.8.2 Temperature, excessive
IEC 80601-2-60:2012, 201.11.1.2.2, applies.
Test in accordance with 7.19.
5.9 Vibrations
ISO 5349-1 and ISO 5349-2 apply.
5.10 Resistance to reprocessing

All handpieces or parts of handpieces shall withstand 250 reprocessing cycles, internally and externally, as

defined by the manufacturer’s instructions, without deterioration in performance or showing signs of corrosion.

The reprocessing cycle shall include the recommended methods of cleaning, disinfection and sterilization.

If the manufacturer states a lower number of permitted reprocessing cycles, then this shall be used in place of

the 250 stated above.
Test in accordance with 7.20.
5.11 Leakage and/or ingress of water
IEC 60601-1:2005, 11.6, applies.
5.12 Electromagnetic compatibility
Test in accordance with 5.6.1.
5.13 Operating controls

The following requirements are applicable for all handpieces and motors described in this International Standard.

Operating controls shall be designed and located to minimize accidental activation. Graphical symbols for

operating controls and performance shall be in accordance with ISO 9687.

By the use of operating controls, air motors shall be capable of changing speed as specified by the manufacturer.

The controls shall be provided at the air motor itself or at the dental unit.

The motor, or motor connected to a dental unit, shall be provided with operator controls to allow clockwise and

anticlockwise rotation, as described by the manufacturer. The controls shall be provided at the motor itself or

at the dental unit.
6 © ISO 2012 – All rights reserved
---------------------- Page: 12 ----------------------
ISO 14457:2012(E)
IEC 60601-1:2005, 15.1, applies.
5.14 Usability
IEC 62366 applies.
5.15 Connection and supply
5.15.1 General
The following requirements are applicable for:
a) high-speed air turbine handpieces;
b) handpiece attachments;
c) air motors;
d) electrical motors.

Handpieces shall be capable of being disconnected from and reconnected to the services without any special tool.

5.15.2 Connections for high-speed air turbine handpiece and air motor connectors
The following requirements are applicable for:
a) high-speed air turbine handpieces;
b) air motors.

The configuration, dimensions and tolerances of connections of the handpieces for drive air, exhaust air, spray

air, cooling water and fibre-optic light, as appropriate, shall be in accordance with ISO 9168.

If the connection is made by a quick connector, the connector shall be in accordance with ISO 9168.

Test in accordance with 7.10.
5.15.3 Connector for handpiece attachments and motors

The configuration, dimensions and tolerances of the back end of the handpieces and front end of the air motor

or electrical motor should comply with ISO 3964.
Test in accordance with 7.9.
5.15.4 Connections for prophy handpieces
5.15.4.1 General
The following requirements are applicable for prophy handpieces.
5.15.4.2 Dimensions

The dimensional aspects of the housing shall comply with the specifications listed in Figure 1 and Figure 2.

Test in accordance with 7.10.
5.15.4.3 Mandrel

The outer diameter of the long-gear mandrel shall be compatible with the coupling specifications listed in

+0 +0

Figure 1. The allowable range will be 2,350 mm mm for metallic materials and 2,350 mm mm for

−0,016 −00
© ISO 2012 – All rights reserved 7
---------------------- Page: 13 ----------------------
ISO 14457:2012(E)

plastic materials, measured at a distance 17 mm from the terminal end of the mandrel. Should the mandrel be

shaped such that there exists a minimum and maximum diameter, the maximum diameter is required to fall

within the allowable range.
Test in accordance with 7.10.
Dimensions in millimetres
Corner or round cut.
0 0
Tolerances: 1) for metallic materials: 2) for plastic materials: .
0,016 0,05
Figure 1 — Angle end dimensions for connection
Dimensions in millimetres
Figure 2 — Handpiece nose dimensions for connection
8 © ISO 2012 – All rights reserved
---------------------- Page: 14 ----------------------
ISO 14457:2012(E)
5.16 Chuck system for shanks
5.16.1 Metallic chuck system

Handpieces with metallic chuck systems shall be capable of accepting rotary instruments of corresponding

mandrels of Type 1, Type 2, Type 4 or test mandrel Type 5 as described in ISO 13295.

The force required to extract the test mandrels (see Figure 3) from the chuck system shall be at least 22 N for

Type 5 and 45 N for Type 3. When locked in the chuck system, test mandrel Type 5 shall transmit a torque of

at least 0,016 N·m; Type 1 and Type 3 shall transmit a torque of at least 0,02 N·m without slipping (in rotation

and linear movement) or showing visible signs of destruction.
Test in accordance with 7.12.
5.16.2 Non-metallic chuck system

Handpieces with non-metallic chuck systems shall be capable of accepting rotary instruments of corresponding

mandrels of Type 5.

The manufacturer of a non-metallic chuck system shall describe in the risk management documentation any

potentially increased risk particular to using the non-metallic chuck.

The force required to extract test mandrel Type 3 from the non-metallic chuck system shall be at least 12 N.

When held in the chuck, test mandrel Type 3 shall transit a torque of at least 0,008 N·m.

Test in accordance with 7.12.
5.17 Test mandrel
The test mandrel shall have the dimensions shown in Figure 3.
Test in accordance with 7.11.
Dimensions in millimetres
a) Test mandrel Type 1
© ISO 2012 – All rights reserved 9
---------------------- Page: 15 ----------------------
ISO 14457:2012(E)
Dimensions in millimetres
b) Test mandrel Type 2
Dimensions in millimetres
c) Test mandrel Type 3
Dimensions in
...

NORME ISO
INTERNATIONALE 14457
Première édition
2012-09-15
Médecine bucco-dentaire — Pièces à
main et moteurs
Dentistry — Handpieces and motors
Numéro de référence
ISO 14457:2012(F)
ISO 2012
---------------------- Page: 1 ----------------------
ISO 14457:2012(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2012

Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous

quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l’accord écrit

de l’ISO à l’adresse ci-après ou du comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2012 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 14457:2012(F)
Sommaire Page

Avant-propos ...................................................................................................................................................................... v

Introduction .......................................................................................................................................................................vi

1 Domaine d’application ....................................................................................................................................... 1

2 Références normatives ...................................................................................................................................... 1

3 Termes et définitions .......................................................................................................................................... 2

4 Classification des pièces à main ..................................................................................................................... 4

5 Exigences et performance ................................................................................................................................ 4

5.1 Généralités ............................................................................................................................................................ 4

5.2 Matériel ................................................................................................................................................................... 4

5.3 Essai de chute ...................................................................................................................................................... 4

5.4 Niveau de bruit ..................................................................................................................................................... 4

5.5 Surfaces ................................................................................................................................................................. 4

5.6 Alimentation en énergie ..................................................................................................................................... 5

5.7 Pression d’air et pression d’eau ..................................................................................................................... 6

5.8 Température .......................................................................................................................................................... 6

5.9 Vibrations .............................................................................................................................................................. 6

5.10 Résistance au retraitement ............................................................................................................................... 6

5.11 Fuite et/ou entrée d’eau ..................................................................................................................................... 6

5.12 Compatibilité électromagnétique .................................................................................................................... 6

5.13 Commandes de fonctionnement ..................................................................................................................... 7

5.14 Aptitude à l’utilisation ........................................................................................................................................ 7

5.15 Connexion et alimentation ................................................................................................................................ 7

5.16 Système de serrage pour queues ................................................................................................................... 9

5.17 Mandrin d’essai .................................................................................................................................................... 9

5.18 Vitesse .................................................................................................................................................................. 11

5.19 Excentricité ......................................................................................................................................................... 11

5.20 Couple .................................................................................................................................................................. 11

5.21 Dimensions de la tête et du nez .................................................................................................................... 11

6 Échantillonnage .................................................................................................................................................12

7 Essais ...................................................................................................................................................................13

7.1 Conditions d’essai générales .........................................................................................................................13

7.2 Inspection visuelle ............................................................................................................................................13

7.3 Alimentation en énergie — Électricité .........................................................................................................13

7.4 Alimentation en énergie — Air .......................................................................................................................13

7.5 Alimentation en air pulvérisé .........................................................................................................................13

7.6 Alimentation en eau pulvérisée .....................................................................................................................14

7.7 Pression d’air et pression d’eau ...................................................................................................................14

7.8 Air de refroidissement du moteur .................................................................................................................14

7.9 Connexion pour raccordement de la pièce à main et de la pièce à main à air comprimé .............14

7.10 Connexion et alimentation ..............................................................................................................................15

7.11 Mandrins d’essai ...............................................................................................................................................15

7.12 Système de serrage pour queues .................................................................................................................15

7.13 Dimensions (de la tête et du nez) ..................................................................................................................16

7.14 Excentricité .........................................................................................................................................................16

7.15 Couple ..................................................................................................................................................................16

7.16 Niveau de bruit ...................................................................................................................................................16

7.17 Vitesse ..................................................................................................................................................................17

7.18 Échauffement du corps ...................................................................................................................................17

7.19 Température excessive ....................................................................................................................................17

7.20 Résistance au retraitement .............................................................................................................................17

8 Instructions d’utilisation, de maintenance et de réparation ..................................................................17

© ISO 2012 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 14457:2012(F)

9 Description technique ......................................................................................................................................18

10 Marquage .............................................................................................................................................................18

10.1 Généralités ..........................................................................................................................................................18

10.2 Pièces à main .....................................................................................................................................................18

10.3 Moteurs ................................................................................................................................................................19

11 Étiquetage ...........................................................................................................................................................19

12 Emballage ............................................................................................................................................................19

Annexe A (informative) Catégories des pièces à main ...........................................................................................20

Bibliographie ....................................................................................................................................................................21

iv © ISO 2012 – Tous droits réservés
---------------------- Page: 4 ----------------------
ISO 14457:2012(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux de

normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général confiée aux

comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité

technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales,

en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec la Commission

électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.

Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI, Partie 2.

La tâche principale des comités techniques est d’élaborer les Normes internationales. Les projets de Normes

internationales adoptés par les comités techniques sont soumis aux comités membres pour vote. Leur publication

comme Normes internationales requiert l’approbation de 75 % au moins des comités membres votants.

L’attention est appelée sur le fait que certains des éléments du présent document peuvent faire l’objet de droits

de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de ne pas avoir

identifié de tels droits de propriété et averti de leur existence.

L’ISO 14457 a été élaborée par le comité technique ISO/TC 106, Médecine bucco-dentaire, sous-comité SC 4,

Instruments dentaires.

Cette première édition de l’ISO 14457 annule et remplace l’ISO 7785-1:1997, l’ISO 7785-2:1995, l’ISO 11498:1997

et l’ISO 13294:1997, qui ont fait l’objet d’une révision technique.
© ISO 2012 – Tous droits réservés v
---------------------- Page: 5 ----------------------
ISO 14457:2012(F)
Introduction

Les pièces à main et les moteurs dentaires sont utilisés dans le domaine des soins dentaires depuis de

nombreuses années.

Les progrès techniques permettent de créer des pièces à main et des moteurs plus faciles à utiliser et plus

performants. La combinaison de ces éléments est très importante pour obtenir une bonne performance.

La présente Norme internationale combine le contenu des quatre Normes internationales suivantes qui ont

été annulées:

— ISO 7785-1:1997, Pièces à main dentaires — Partie 1: Pièces à main à turbines à air comprimé pour

grandes vitesses

— ISO 7785-2:1995, Pièces à main dentaires — Partie 2: Pièces à main rectilignes et à contre-angles

— ISO 11498:1997, Pièces à main dentaires — Moteurs électriques dentaires à basse tension

— ISO 13294:1997, Pièces à main dentaires — Moteurs dentaires à air
vi © ISO 2012 – Tous droits réservés
---------------------- Page: 6 ----------------------
NORME INTERNATIONALE ISO 14457:2012(F)
Médecine bucco-dentaire — Pièces à main et moteurs
1 Domaine d’application

La présente Norme internationale s’applique aux pièces à main et aux moteurs utilisés en médecine bucco-

dentaire pour le contact patient, quelle que soit leur construction. Elle spécifie les exigences, les méthodes

d’essai, les informations du fabricant, le marquage et l’emballage.
La présente Norme internationale s’applique

a) aux pièces à main rectilignes et à contre-angles, y compris aux raccordements de la pièce à main,

b) aux pièces à main à turbines à air comprimé pour grandes vitesses,
c) aux moteurs à air,
d) aux moteurs électriques, et
e) aux pièces de prophylaxie.
La présente Norme internationale ne s’applique pas
1) aux pièces à main à caméras intrabuccales,
2) aux pièces à main alimentées en énergie pour polymérisation,
3) aux instruments pour détartrage à air comprimé,
4) aux instruments pour détartrage électriques,
5) aux pièces à main pour polissage à air comprimé, et
6) aux pièces à main multifonctions (seringues).

NOTE Voir l’Annexe A pour clarifier les types de pièces à main, de raccordements et de moteurs couverts par la

présente Norme internationale.
2 Références normatives

Les documents de référence suivants sont indispensables à l’application du présent document. Pour les

références datées, seule l’édition citée s’applique. Pour les références non datées, la dernière édition du

document de référence s’applique (y compris les éventuels amendements).

ISO 1797-1, Médecine bucco-dentaire — Queues pour instruments rotatifs — Partie 1: Queues en

matériaux métalliques

ISO 1797-2, Instruments rotatifs dentaires — Queues — Partie 2: Queues en matières plastiques

ISO 1942, Médecine bucco-dentaire — Vocabulaire
ISO 3964, Pièces à main dentaires — Dimensions d’accouplement

ISO 5349-1, Vibrations mécaniques — Mesurage et évaluation de l’exposition des individus aux vibrations

transmises par la main — Partie 1: Exigences générales

ISO 5349-2, Vibrations mécaniques ― Mesurage et évaluation de l’exposition des individus aux vibrations

transmises par la main — Partie 2: Guide pratique pour le mesurage sur le lieu de travail

ISO 6507-1, Matériaux métalliques — Essai de dureté Vickers — Partie 1: Méthodes d’essai

© ISO 2012 – Tous droits réservés 1
---------------------- Page: 7 ----------------------
ISO 14457:2012(F)

ISO 7405, Art dentaire — Évaluation de la biocompatibilité des dispositifs médicaux utilisés en art dentaire

ISO 7494-1, Médecine bucco-dentaire — Units dentaires — Partie 1: Exigences générales et méthodes d’essai

ISO 9168, Art dentaire — Connexions pour pièces à main dentaires à air comprimé
ISO 9687, Matériel dentaire — Symboles graphiques

ISO 10993-1, Évaluation biologique des dispositifs médicaux — Partie 1: Évaluation et essais au sein d’un

processus de gestion du risque
ISO 13295, Art dentaire — Mandrins pour instruments rotatifs

ISO 15223-1, Dispositifs médicaux — Symboles à utiliser avec les étiquettes, l’étiquetage et les informations à

fournir relatifs aux dispositifs médicaux — Partie 1: Exigences générales

ISO 17664, Stérilisation des dispositifs médicaux — Informations devant être fournies par le fabricant pour le

processus de restérilisation des dispositifs médicaux
ISO 21531, Art dentaire — Symboles graphiques pour instruments dentaires

CEI 60601-1:2005, Appareils électromédicaux — Partie 1: Exigences générales pour la sécurité de base et les

performances essentielles
CEI 61672-1, Électroacoustique — Sonomètres — Partie 1: Spécifications

CEI 62366, Dispositifs médicaux — Application de l’ingénierie de l’aptitude à l’utilisation aux dispositifs médicaux

CEI 80601-2-60:2012, Appareils électromédicaux — Partie 2-60: Exigences particulières pour la sécurité de

base et les performances essentielles des équipements dentaires
3 Termes et définitions

Pour les besoins du présent document, les termes et définitions suivants et ceux donnés dans l’ISO 1942

s’appliquent.
3.1
moteur à air
moteur actionné par de l’air comprimé, fourni par un unit dentaire
3.2
pièce à main à air comprimé à jet de poudre

pièce à main actionnée par de l’air comprimé, conçue pour envoyer un jet de poudre au patient

3.3
instrument pour détartrage à air comprimé

pièce à main actionnée par de l’air comprimé, équipée d’une partie de travail oscillante

3.4
pièce à main angulaire

pièce à main dont l’axe d’entrée et l’axe de sortie forment un angle, entraînée par un moteur à air ou électrique

ou équipée d’une alimentation interne
3.5
pièce à main à contre-angles

pièce à main angulaire comportant un ou plusieurs angles supplémentaires configurés de façon que la partie

de travail de l’instrument ou de l’outil soit approximativement alignée sur l’axe principal de la pièce à main

3.6
système de serrage non métallique

système de serrage de la pièce à main dont la surface de contact du mécanisme porte-queue est constituée

d’un matériau non métallique
2 © ISO 2012 – Tous droits réservés
---------------------- Page: 8 ----------------------
ISO 14457:2012(F)
3.7
moteur électrique
moteur actionné par de l’énergie électrique, fournie par un unit dentaire
3.8
instrument pour détartrage électrique

pièce à main actionnée par de l’énergie électrique, équipée d’une partie de travail oscillante

3.9
partie de travail
partie d’un instrument fixe ou interchangeable raccordée à une pièce à main
3.10
pièce à main

instrument portatif motorisé utilisé pour actionner une partie de travail rotative, oscillante ou alternative

3.11
raccordement de la pièce à main
partie d’extension d’une pièce à main conçue pour fixer une partie de travail
3.12
système de serrage de la pièce à main

partie de la pièce à main conçue pour fixer solidement la queue d’une partie de travail

3.13
pièce à main à turbines à air comprimé pour grandes vitesses

pièce à main propulsée par une petite turbine (ou rotor) à air comprimé, capable de grandes vitesses, intégrée

dans la tête de la pièce à main et possédant un dispositif de serrage coaxial à la turbine

3.14
pièce à main à caméras intrabuccales
pièce à main conçue pour réaliser des vidéos de la cavité buccale du patient
3.15
moteur

dispositif, alimenté en air ou en électricité fourni par un unit dentaire, conçu pour transformer l’énergie en mouvement

3.16
pièce à main pour polymérisation

pièce à main produisant une lumière appliquée directement dans la cavité buccale d’un patient sur des

matériaux dentaires polymérisables
3.17
pièce de prophylaxie

pièce à main angulaire utilisée pour la prophylaxie dentaire, entraînée par un moteur à air ou électrique

3.18
instrument rotatif

instrument rotatif utilisé dans une pièce à main à turbines à air comprimé pour grandes vitesses ou dans une

pièce à main rectiligne et à contre-angles, constitué d’une queue et d’une extrémité de travail utilisées pour les

procédures dentaires
3.19
instrument alternatif

instrument oscillant utilisé dans une pièce à main à turbines à air comprimé pour grandes vitesses ou dans une

pièce à main rectiligne et à contre-angles, constitué d’une queue et d’une extrémité de travail utilisées pour les

procédures dentaires
3.20
pièce à main rectiligne

pièce à main dont les axes d’entrée et de sortie sont alignés, entraînée par un moteur à air ou électrique ou

équipée d’une alimentation interne
© ISO 2012 – Tous droits réservés 3
---------------------- Page: 9 ----------------------
ISO 14457:2012(F)
3.21
pièce de transmission

petit outil (rotatif ou alternatif) conçu pour transmettre de l’énergie de la queue à l’extrémité de travail

3.22
extrémité de travail

extrémité distale d’un instrument rotatif ou oscillant conçue pour une utilisation directe dans la cavité

buccale du patient
4 Classification des pièces à main

Les pièces à main sont classées en fonction de leur rapport d’engrenage, en trois types de catégories indiquées

dans le Tableau 1.
Tableau 1 — Rapports d’engrenage des pièces à main
Type Rapport Vitesse de rotation obtenue Couple obtenu Couleur
d’engrenage
1 >1:1 inférieure supérieur verte
2 1:1 constante constant bleue
3 1:>1 supérieure inférieur rouge
5 Exigences et performance
5.1 Généralités

La construction des pièces à main doit garantir un fonctionnement sûr et fiable de celles-ci. Elles doivent être

simples et pratiques à utiliser et à manipuler par l’opérateur. Ces exigences doivent être conformes à la CEI 62366.

Si elles peuvent être réparées sur site, les pièces à main doivent pouvoir être facilement démontées et

remontées en vue de la maintenance et de la réparation, en utilisant soit des outils déjà disponibles, soit des

outils spéciaux fournis par le fabricant.
Les exigences électriques s’appliquent uniquement aux pièces à main électriques.
5.2 Matériel

Les essais de biocompatibilité doivent être conformes à l’ISO 7405 et à l’ISO 10993-1.

5.3 Essai de chute
La CEI 60601-1:2005,15.3.4.1, s’applique.
5.4 Niveau de bruit

Le niveau de pression acoustique pondéré A produit par la pièce à main ne doit pas dépasser 80 dB.

Soumettre à essai conformément à 7.16.

NOTE Dans la pratique, cet essai s’applique à chaque pièce à main en tant que système, c’est-à-dire chaque

raccordement utilisé avec son moteur d’entraînement respectif.
5.5 Surfaces

Il convient de prêter une attention particulière à la fourniture de surfaces de prise en main bien adhérentes en

vue de la manipulation par l’opérateur dans des conditions d’utilisation normales.

4 © ISO 2012 – Tous droits réservés
---------------------- Page: 10 ----------------------
ISO 14457:2012(F)
Soumettre à essai conformément à la CEI 62366.

NOTE Pour réduire l’éblouissement, il convient d’éviter d’utiliser des surfaces hautement polies.

5.6 Alimentation en énergie
5.6.1 Alimentation en énergie électrique
Les exigences suivantes s’appliquent
a) aux moteurs électriques,
b) aux pièces à main intégrées dans le moteur, et
c) aux pièces de prophylaxie intégrées dans le moteur.

Les exigences doivent être spécifiées par le fabricant et être conformes à l’ISO 7494-1.

Soumettre à essai conformément à 7.3.
5.6.2 Alimentation en air
5.6.2.1 Pièce à main à air comprimé
Les exigences suivantes s’appliquent
a) aux pièces à main à turbines à air comprimé pour grandes vitesses,
b) aux moteurs à air,
c) aux pièces à main intégrées dans le moteur à air, et
d) aux pièces de prophylaxie intégrées dans le moteur à air.

Les pièces à main à air comprimé doivent être actionnées par une alimentation en air comprimé conforme

aux instructions du fabricant. Le débit nécessaire doit être <66 Nl/min dans une gamme de pression de

(300 ± 100) kPa [(3,0 ± 1,0) bar].
Soumettre à essai conformément à 7.4.
5.6.2.2 Air de refroidissement du moteur
L’exigence suivante s’applique aux moteurs électriques.

Si le moteur électrique est équipé d’un système de refroidissement par l’air, il convient que le débit d’air maximal ne

dépasse pas 40 Nl/min et que la gamme de pression soit comprise entre 250 kPa et 500 kPa (2,5 bar et 5,0 bar).

Il convient que le moteur électrique soit muni d’un raccord de sortie pour le refroidissement par l’air du moteur.

Soumettre à essai conformément à 7.8.
5.6.2.3 Alimentation en air pulvérisé

La capacité de refroidissement à l’air pulvérisé peut être laissée à la discrétion du fabricant. Les pièces à

main ayant une capacité de refroidissement à l’air pulvérisé doivent diriger l’air sur la zone de fonctionnement

de l’instrument rotatif. Si de l’eau et de l’air sont utilisés simultanément, un spray de refroidissement doit être

produit et transmis sur la zone de coupe d’un instrument rotatif. La pièce à main doit être capable d’atteindre

un débit d’air d’au moins 1,5 Nl/min à 200 kPa (2,0 bar).

Les moteurs doivent être équipés, le cas échéant, d’un moyen de transmission de l’air à un raccordement de la

pièce à main. L’équipement doit être capable d’atteindre un débit d’air d’au moins 1,5 Nl/min à 200 kPa (2,0 bar).

© ISO 2012 – Tous droits réservés 5
---------------------- Page: 11 ----------------------
ISO 14457:2012(F)
Soumettre à essai conformément à 7.5.
5.6.3 Alimentation en eau

Le cas échéant, la pièce à main doit pouvoir refroidir, avec de l’eau, la zone de fonctionnement de la partie de

travail, à un débit d’au moins 50 ml/min à 250 kPa (2,5 bar).
Soumettre à essai conformément à 7.6.
5.7 Pression d’air et pression d’eau

Le cas échéant, les moteurs et les pièces à main doivent rester intacts, ce qui signifie qu’ils ne doivent pas se

casser ou exploser lorsqu’ils sont soumis à une pression 50 % au-dessus de la pression de fonctionnement

maximale recommandée par le fabricant.
Soumettre à essai conformément à 7.7.
5.8 Température
5.8.1 Échauffement du corps
La CEI 80601-2-60:2012, 201.11.1.1, s’applique.
Soumettre à essai conformément à 7.18.
5.8.2 Température excessive
La CEI 80601-2-60:2012, 201.11.2.2, s’applique.
Soumettre à essai conformément à 7.19.
5.9 Vibrations
L’ISO 5349-1 et l’ISO 5349-2 s’appliquent.
5.10 Résistance au retraitement

Toutes les pièces à main ou parties des pièces à main doivent supporter 250 cycles de retraitement, au niveau

interne et externe, conformément aux instructions données par le fabricant, sans présenter de détérioration

des performances ou de signes de corrosion. Le cycle de retraitement doit comprendre les méthodes

recommandées de nettoyage, de désinfection et de stérilisation.

Si le fabricant indique un nombre moins élevé de cycles de retraitement autorisés, alors ce nombre doit être

utilisé à la place des 250 énoncés.
Soumettre à essai conformément à 7.20.
5.11 Fuite et/ou entrée d’eau
La CEI 60601-1:2005, 11.6, s’applique.
5.12 Compatibilité électromagnétique
Soumettre à essai conformément à 5.6.1.
6 © ISO 2012 – Tous droits réservés
---------------------- Page: 12 ----------------------
ISO 14457:2012(F)
5.13 Commandes de fonctionnement

Les exigences suivantes sont applicables à toutes les pièces à main et tous les moteurs décrits dans la

présente Norme internationale.

Les commandes de fonctionnement doivent être conçues et situées de façon à réduire au minimum tout

risque d’activation accidentelle. Les symboles graphiques relatifs aux commandes de fonctionnement et aux

performances doivent être conformes à l’ISO 9687.

Grâce aux commandes de fonctionnement, les moteurs à air doivent pouvoir changer de vitesse, conformément

aux spécifications du fabricant. Les commandes doivent se situer sur le moteur à air lui-même ou sur l’unit dentaire.

Le moteur ou le moteur connecté à un unit dentaire, doit être muni de commandes de fonctionnement

permettant une rotation dans le sens des aiguilles d’une montre et dans le sens inverse des aiguilles d’une

montre, conformément à la description du fabricant. Les commandes doivent se situer sur le moteur lui-même

ou sur l’unit dentaire.
La CEI 60601-1:2005, 15.1, s’applique.
5.14 Aptitude à l’utilisation
La CEI 62366 s’applique.
5.15 Connexion et alimentation
5.15.1 Généralités
Les exigences suivantes s’appliquent
a) aux pièces à main à turbines à air comprimé pour grandes vitesses,
b) aux raccordements de la pièce à main,
c) aux moteurs à air, et
d) aux moteurs électriques.

Les pièces à main doivent pouvoir être déconnectées et reconnectées aux équipements techniques sans

outil spécial.

5.15.2 Connexions pour pièces à main à turbines à air comprimé pour grandes vitesses et pour rac-

cords du moteur à air
Les exigences suivantes s’appliquent
a) aux pièces à main à turbines à air comprimé pour grandes vitesses, et
b) aux moteurs à air.

Il convient que la configuration et les dimensions ainsi que les tolérances associées, des connexions des

pièces à main pour l’air d’alimentation, l’air évacué, l’air pulvérisé, l’eau de refroidissement et la lumière à fibre

optique, le cas échéant, soient conformes à l’ISO 9168.

Si la connexion est effectuée à l’aide d’un raccord rapide, ce dernier doit être conforme à l’ISO 9168.

Soumettre à essai conformément à 7.10.
5.15.3 Connexions pour raccordements de la pièce à main et moteurs

Il convient que la configuration et les dimensions ainsi que les tolérances associées, de l’extrémité arrière des

pièces à main et de l’extrémité avant du moteur à air ou du moteur électrique, soient

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.