ISO 8606:2025
(Main)Fibre-reinforced plastics — Bulk moulding compound (BMC) and dough moulding compound (DMC) — Requirements and specifications
Fibre-reinforced plastics — Bulk moulding compound (BMC) and dough moulding compound (DMC) — Requirements and specifications
This document establishes requirements and specifications of the bulk moulding compound (BMC) and dough moulding compound (DMC) with or without thickening agents. This document is applicable to BMC and DMC, which are different types of preimpregnated product used for the production, by moulding, of various parts made of composite materials. The scope is not limited to types of fibres and resins.
Plastiques renforcés de fibres — Préimprégnés en masse BMC et DMC — Exigences et spécifications
La présente Norme internationale établit une base de spécification pour mélanges à mouler en masse, avec ou sans agents épaississants, dits BMC (Bulk Moulding Compound) et DMC (Dough Moulding Compound) qui figurent parmi les différents types de produits préimprégnés destinés, par pressage à chaud, à la réalisation de pièces diverses en matériaux composites. Pour les besoins de la présente Norme internationale, seuls sont considérés les mélanges à mouler en masse (BMC et DMC) dont le renfort unique (ou prépondérant) est constitué de fibres de verre.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 8606
Second edition
Fibre-reinforced plastics — Bulk
2025-07
moulding compound (BMC) and
dough moulding compound (DMC)
— Requirements and specifications
Plastiques renforcés de fibres — Préimprégnés en masse BMC et
DMC — Exigences et spécifications
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification of BMC and DMC . 3
4.1 General .3
4.2 Classification based on composition .3
4.2.1 Resin (matrix) .3
4.2.2 Reinforcement(s) .4
4.2.3 Other components .4
4.2.4 Recycling .4
4.3 Classification based on linear shrinkage .4
4.3.1 General-purpose BMC or DMC .4
4.3.2 Low-shrink BMC or DMC .5
4.3.3 Very-low-shrink (low profile) BMC or DMC .5
4.3.4 Zero-shrink BMC or DMC .5
5 Designation of BMC and DMC . 5
5.1 General .5
5.2 Examples of designations .5
6 Properties . 6
6.1 General .6
6.2 Properties to describe BMC or DMC (for the acceptance test) .6
6.2.1 Physical and chemical properties .6
6.2.2 Appearance .6
6.3 Properties to describe moulded specimens .7
6.3.1 General .7
6.3.2 Mechanical properties . .7
6.3.3 Physical properties.7
6.3.4 Electrical properties .7
7 Sampling . 8
7.1 Sampling procedure .8
7.2 Conditioning of sample .8
8 Shelf life . 8
9 Packaging and marking . 8
9.1 Packaging .8
9.2 Marking .8
Bibliography .10
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites
and reinforcement fibres.
This second edition cancels and replaces the first edition (ISO 8606:1990), which has been technically
revised.
The main changes are as follows:
— the title has been modified from “Plastics — Prepregs — Bulk moulding compound (BMC) and dough
moulding compound (DMC) — Basis for a specification” to “Fibre-reinforced plastics — Bulk moulding
compound (BMC) and dough moulding compound (DMC) — Requirements and specifications”;
— fibre type and shrinkage code have been added;
— the designation of BMC or DMC has been added;
— test properties have been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 8606:2025(en)
Fibre-reinforced plastics — Bulk moulding compound (BMC)
and dough moulding compound (DMC) — Requirements and
specifications
1 Scope
This document establishes requirements and specifications of the bulk moulding compound (BMC) and
dough moulding compound (DMC) with or without thickening agents.
This document is applicable to BMC and DMC, which are different types of preimpregnated product used for
the production, by moulding, of various parts made of composite materials.
The scope is not limited to types of fibres and resins.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 62:2008, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 180, Plastics — Determination of Izod impact strength
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 472, Plastics — Vocabulary
ISO 527-4, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic
fibre-reinforced plastic composites
ISO 1172, Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of
the textile-glass and mineral-filler content using calcination methods
ISO 1183 (all parts), Plastics — Methods for determining the density of non-cellular plastics
ISO 2577, Plastics — Thermosetting moulding materials — Determination of shrinkage
ISO 4589-2, Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 9782, Plastics — Reinforced moulding compounds and prepregs — Determination of apparent volatile-
matter content
ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
ISO 11667, Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-
fibre and mineral-filler content — Dissolution methods
ISO 12114, Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of
cure characteristics
ISO 12115, Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of
flowability, maturation and shelf life
ISO 14125, Fibre-reinforced plastic composites — Determination of flexural properties
...
FINAL DRAFT
International
Standard
ISO/FDIS 8606
ISO/TC 61/SC 13
Fibre-reinforced plastics — Bulk
Secretariat: JISC
moulding compound (BMC) and
Voting begins on:
dough moulding compound (DMC)
2025-04-23
— Requirements and specifications
Voting terminates on:
2025-06-18
Plastiques renforcés de fibres — Préimprégnés en masse BMC et
DMC — Exigences et spécifications
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 8606:2025(en) © ISO 2025
FINAL DRAFT
ISO/FDIS 8606:2025(en)
International
Standard
ISO/FDIS 8606
ISO/TC 61/SC 13
Fibre-reinforced plastics — Bulk
Secretariat: JISC
moulding compound (BMC) and
Voting begins on:
dough moulding compound (DMC)
— Requirements and specifications
Voting terminates on:
Plastiques renforcés de fibres — Préimprégnés en masse BMC et
DMC — Exigences et spécifications
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2025
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 8606:2025(en) © ISO 2025
ii
ISO/FDIS 8606:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification of BMC and DMC . 3
4.1 General .3
4.2 Classification based on composition .3
4.2.1 Resin (matrix) .3
4.2.2 Reinforcement(s) .4
4.2.3 Other components .4
4.2.4 Recycling .4
4.3 Classification based on linear shrinkage .4
4.3.1 General-purpose BMC or DMC .4
4.3.2 Low-shrink BMC or DMC .5
4.3.3 Very-low-shrink (low profile) BMC or DMC .5
4.3.4 Zero-shrink BMC or DMC .5
5 Designation of BMC and DMC . 5
5.1 General .5
5.2 Examples of designations .5
6 Properties . 6
6.1 General .6
6.2 Properties to describe BMC or DMC (for the acceptance test) .6
6.2.1 Physical and chemical properties .6
6.2.2 Appearance .6
6.3 Properties to describe moulded specimens .7
6.3.1 General .7
6.3.2 Mechanical properties . .7
6.3.3 Physical properties.7
6.3.4 Electrical properties .7
7 Sampling . 8
7.1 Sampling procedure .8
7.2 Conditioning of sample .8
8 Shelf life . 8
9 Packaging and marking . 8
9.1 Packaging .8
9.2 Marking .8
Bibliography .10
iii
ISO/FDIS 8606:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites
and reinforcement fibres.
This second edition cancels and replaces the first edition (ISO 8606:1990), which has been technically
revised.
The main changes are as follows:
— the title has been modified from “Plastics — Prepregs — Bulk moulding compound (BMC) and dough
moulding compound (DMC) — Basis for a specification” to “Fibre-reinforced plastics — Bulk moulding
compound (BMC) and dough moulding compound (DMC) — Requirements and specifications”;
— fibre type and shrinkage code have been added;
— the designation of BMC or DMC has been added;
— test properties have been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
FINAL DRAFT International Standard ISO/FDIS 8606:2025(en)
Fibre-reinforced plastics — Bulk moulding compound (BMC)
and dough moulding compound (DMC) — Requirements and
specifications
1 Scope
This document establishes requirements and specifications of the bulk moulding compound (BMC) and
dough moulding compound (DMC) with or without thickening agents.
This document is applicable to BMC and DMC, which are different types of preimpregnated product used for
the production, by moulding, of various parts made of composite materials.
The scope is not limited to types of fibres and resins.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 62:2008, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 180, Plastics — Determination of Izod impact strength
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 472, Plastics — Vocabulary
ISO 527-4, Plastics — Determina
...
Style Definition
...
ISO/FDIS 8606:2025(en)
Formatted: French (Switzerland)
ISO/TC 61/SC 13/WG 2
Formatted: zzCover large
Formatted: Left: 1.5 cm, Right: 1.5 cm, Section start:
Secretariat: JISC
New page, Header distance from edge: 1.27 cm, Footer
distance from edge: 1.27 cm
Date: 2025-03-1804-09
Formatted
...
Formatted: Cover Title_A1
Fibre-reinforced plastics — Bulk moulding compound (BMC) and
dough moulding compound (DMC) — Requirements and
specifications
Plastiques renforcés de fibres — Préimprégnés en masse BMC et DMC — Exigences et spécifications
FDIS stage
ISO /FDIS 8606:####(E:2025(en) Formatted: Font: Bold
Formatted: HeaderCentered
Formatted: Font: Bold, English (United Kingdom)
Formatted: Font: Bold
Formatted: Default Paragraph Font
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
Formatted: Adjust space between Latin and Asian text,
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
Adjust space between Asian text and numbers
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO'sISO’s member body in the country of the requester.
ISO copyright office
Formatted: zzCopyright address, Indent: First line: 0 cm,
CP 401 • Ch. de Blandonnet 8 Adjust space between Latin and Asian text, Adjust space
between Asian text and numbers
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Field Code Changed
Formatted: English (United Kingdom)
Published in Switzerland
Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers
Formatted: FooterPageRomanNumber, Line spacing:
single
Formatted: Font: 11 pt
ii © ISO #### 2025 – All rights reserved
ii
ISO/DISFDIS 8606:20242025(en) Formatted: Font: Bold
Formatted: HeaderCentered
Formatted: Font: Bold
Contents
Formatted: Font: Bold
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Classification of BMC and DMC . 3
5 Designation of BMC and DMC . 5
6 Properties . 6
7 Sampling . 9
8 Shelf life . 9
9 Packaging and marking . 9
Bibliography . 11
Foreword . iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Classification of BMC and DMC . 3
5 Designation of BMC and DMC . 6
6 Properties . 6
7 Sampling . 9
8 Shelf life . 9
9 Packaging and marking . 9
Bibliography . 11
Formatted: Font: 10 pt
Formatted: FooterCentered, Left, Line spacing: single
Formatted: Font: 10 pt
Formatted: Font: 11 pt
Formatted: FooterPageRomanNumber, Left, Space After:
0 pt, Line spacing: single
iii
ISO /FDIS 8606:####(E:2025(en) Formatted: Font: Bold
Formatted: HeaderCentered
Formatted: Font: Bold, English (United Kingdom)
Foreword
Formatted: Font: Bold
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Formatted: English (United Kingdom)
Field Code Changed
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents.www.iso.org/patents. ISO shall not be held responsible for identifying any or all such
patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html. Field Code Changed
Formatted: English (United Kingdom)
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites
and reinforcement fibres.
This second edition cancels and replaces the first edition (ISO 8606:1990), which has been technically revised.
The main changes are as follows:
— — the title has been modified from “Plastics — Prepregs — Bulk moulding compound (BMC) and dough
moulding compound (DMC) — Basis for a specification” to “Fibre-reinforced plastics — Bulk moulding
compound (BMC) and dough moulding compound (DMC) — Requirements and specifications”;
— — fibre type and shrinkage code have been added;
— — the designation of BMC or DMC has been added;
— — test properties have been added.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html. Field Code Changed
Formatted: English (United Kingdom)
Formatted: FooterPageRomanNumber, Line spacing:
single
Formatted: Font: 11 pt
iv © ISO #### 2025 – All rights reserved
iv
ISO/DIS 8606:2024(en)
DRAFT International Standard
Fibre-reinforced plastics — Bulk moulding compound (BMC) and
dough moulding compound (DMC) — Requirements and specifications
1 Scope
This document establishes requirements and specifications of the bulk moulding compound (BMC) and dough
moulding compound (DMC) with or without thickening agents.
This document is applicable to BMC and DMC, which are different types of preimpregnated product used for
Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers
the production, by moulding, of various parts made of composite materials.
It is applicable to BMC and DMC. The scope is not limited to types of fibres and resins.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 62:2008, Plastics — Determination of water absorption Formatted: Default Paragraph Font
Formatted: Adjust space between Latin and Asian text,
ISO 75--2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
Adjust space between Asian text and numbers, Tab stops:
Not at 0.7 cm + 1.4 cm + 2.1 cm + 2.8 cm + 3.5 cm + 4.2
cm + 4.9 cm + 5.6 cm + 6.3 cm + 7 cm
ISO 179--1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
Formatted
...
ISO 179--2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
Formatted
...
Formatted
...
ISO 180, Plastics — Determination of Izod impact strength
Formatted
...
ISO 291, Plastics — Standard atmospheres for conditioning and testing
Formatted
...
Formatted
...
ISO 472, Plastics — Vocabulary
Formatted
...
ISO 527--4:2023, Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and
Formatted
...
orthotropic fibre-reinforced plastic composites
ISO 1172, Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of Formatted
...
the textile-glass and mineral-filler content using calcination methods
ISO 1183 (all parts), Plastics — Methods for determining the density of non-cellular plastics
Formatted
...
Formatted
...
ISO 2577, Plastics — Thermosetting moulding materials — Determination of shrinkage
Formatted
...
ISO 4589--2, Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature
Formatted: Default Paragraph Font
test
Formatted: Adjust space between Latin and Asian text,
Adjust space between Asian text and numbers, Tab stops:
ISO 8604, Plastics — Prepregs — Definitions of terms and symbols for designations Not at 0.7 cm + 1.4 cm + 2.1 cm + 2.8 cm + 3.5 cm + 4.2
cm + 4.9 cm + 5.6 cm + 6.3 cm + 7 cm
ISO 9782, Plastics — Reinforced moulding compounds and prepregs — Determination of apparent volatile-
Formatted
...
matter content
Formatted: Left, Space After: 0 pt, Line spacing: single
ISO/FDIS 8606:2025(en) Formatted: HeaderCentered
Formatted: Font: Bold
ISO 11359--2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
ISO 11667, Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-
fibre and mineral-filler content — Dissolution methods
ISO 12114, Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of
cure characteristics
ISO 12115, Fibre-reinforced plastics — Thermosetting moulding compounds and prepregs — Determination of
flowability, maturation and shelf life
ISO 14125, Fibre-reinforced plastic composites — Determination of flexural properties
ISO 14126, Fibre-reinforced plastic composites — Determination of compressive properties in the in-plane
direction
ISO 14127, Carbon-fibre-reinforced composites — Determination of the resin, fibre and void contents
ISO 14130, Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by
short-beam method
ISO 19927, Fibre-reinforced plastic composites — Determination of interlaminar strength and modulus by
double beam shear test
ISO 22821, Carbon-fibre-reinforced composites — Determination of fibre weight content by thermogravimetry
(TG)
IEC 60112, Method for the determination of the proof and the comparative tracking indices of solid insulating
materials
IEC 60243 (all parts), Electric strength of insulating materials — Test methods
IEC 60587, Electrical insulating materials used under severe ambient conditions — Test methods for evaluating
resistance to tracking and erosion
IEC 60695--2-12, Fire hazard testing — Part 2-12: Glowing/hot-wire based test methods — Glow-wire
flammability index (GWFI) test method for materials
IEC 60695--11-10, Fire hazard testing — Part 11-10: Test flames — 50 W horizontal and vertical flame test
methods
IEC 61621, Dry, soli
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.