Alpine skis -- Determination of mass and polar moment of inertia -- Laboratory measurement method

ISO 6003:2017 specifies laboratory measurement methods for mass and polar moment of inertia of alpine skis. If laboratory measurement data are determined and published by the ski manufacturer or other institutions, standard measurement procedures can be used to ensure comparability. ISO 6003:2017 also specifies a tolerance range which can be met by the measurement data of all manufactured skis, if for the specific model length measurement data are published by the manufacturer of the ski. NOTE The appropriate ski length can be given with the published measurement data. ISO 6003:2017 is not the purpose of this document to evaluate the measurement data with regard to their influence on the quality of the ski.

Skis alpins -- Détermination de la masse et du moment d'inertie polaire -- Méthode de mesurage en laboratoire

ISO 6003:2017 spécifie des méthodes de mesure en laboratoire de la masse et du moment d'inertie polaire des skis alpins. Si des résultats de mesure sont obtenus en laboratoire et publiés par le fabricant de skis ou tout autre organisme, des modes opératoires de mesure normalisés peuvent ętre utilisés pour s'assurer que les résultats soient comparables. ISO 6003:2017 spécifie également une plage de tolérance dans laquelle peuvent se situer les résultats de mesure obtenus sur tous les skis fabriqués si, pour les modčles concernés, les résultats de mesure de la longueur sont publiés par le fabricant des skis. NOTE La longueur appropriée des skis peut ętre fournie avec les résultats de mesure publiés. ISO 6003:2017 n'a pas pour but d'évaluer l'incidence des résultats de mesure sur la qualité du ski.

Alpske smuči - Določevanje mase in polarnega vztrajnostnega momenta - Metoda za laboratorijsko merjenje

Ta dokument določa metodo za laboratorijsko merjenje masnega vztrajnostnega momenta in vztrajnostnega momenta ploskve pri alpskih smučeh.
Če podatke laboratorijskih meritev pridobijo in objavijo proizvajalci smuči ali druge ustanove, je mogoče uporabiti standardne merilne postopke za zagotovitev primerljivosti.
Poleg tega ta dokument določa razpon dovoljenega odstopanja, ki ga lahko dosežejo vsi merilni podatki vseh proizvedenih smuči, če prodajalec smuči objavi podatke meritev za dolžino specifičnega modela.
OPOMBA: Ustrezna dolžina smuči je lahko podana skupaj z objavljenimi merilnimi podatki.
Namen tega dokumenta ni vrednotenje merilnih podatkov z vidika njihovega vpliva na kakovost smuči.

General Information

Status
Published
Publication Date
04-Dec-2017
Current Stage
6060 - International Standard published
Start Date
01-Nov-2017
Completion Date
05-Dec-2017

RELATIONS

Buy Standard

Standard
ISO 6003:2017 - Alpine skis -- Determination of mass and polar moment of inertia -- Laboratory measurement method
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 6003:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ISO 6003:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ISO 6003:2017 - Skis alpins -- Détermination de la masse et du moment d'inertie polaire -- Méthode de mesurage en laboratoire
French language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

INTERNATIONAL ISO
STANDARD 6003
Third edition
2017-11
Alpine skis — Determination of
mass and polar moment of inertia —
Laboratory measurement method
Skis alpins — Détermination de la masse et du moment d'inertie
polaire — Méthode de mesurage en laboratoire
Reference number
ISO 6003:2017(E)
ISO 2017
---------------------- Page: 1 ----------------------
ISO 6003:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 6003:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Apparatus ..................................................................................................................................................................................................................... 1

5 Sampling and conditioning ........................................................................................................................................................................ 2

6 Calibration of measuring device .......................................................................................................................................................... 2

7 Procedure..................................................................................................................................................................................................................... 3

8 Expression of results ........................................................................................................................................................................................ 4

8.1 Mass of the ski ......................................................................................................................................................................................... 4

8.2 Polar moment of inertia of the ski .......................................................................................................................................... 4

9 Tolerances ................................................................................................................................................................................................................... 6

9.1 Measurement tolerances ................................................................................................................................................................ 6

9.2 Tolerances on published data .................................................................................................................................................... 6

10 Test report ................................................................................................................................................................................................................... 6

© ISO 2017 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO 6003:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This third edition cancels and replaces the second edition (ISO 6003:1984), which has been technically

revised.
iv © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
INTERNATIONAL STANDARD ISO 6003:2017(E)
Alpine skis — Determination of mass and polar moment of
inertia — Laboratory measurement method
1 Scope

This document specifies laboratory measurement methods for mass and polar moment of inertia of

alpine skis.

If laboratory measurement data are determined and published by the ski manufacturer or other

institutions, standard measurement procedures can be used to ensure comparability.

This document also specifies a tolerance range which can be met by the measurement data of all

manufactured skis, if for the specific model length measurement data are published by the manufacturer

of the ski.

NOTE The appropriate ski length can be given with the published measurement data.

It is not the purpose of this document to evaluate the measurement data with regard to their influence

on the quality of the
...

SLOVENSKI STANDARD
oSIST ISO 6003:2018
01-julij-2018
$OSVNHVPXþL'RORþHYDQMHPDVHLQSRODUQHJDY]WUDMQRVWQHJDPRPHQWD0HWRGD
]DODERUDWRULMVNRPHUMHQMH
Alpine skis -- Determination of mass and polar moment of inertia -- Laboratory
measurement method

Skis alpins -- Détermination de la masse et du moment d'inertie polaire -- Méthode de

mesurage en laboratoire
Ta slovenski standard je istoveten z: ISO 6003:2017
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
oSIST ISO 6003:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST ISO 6003:2018
---------------------- Page: 2 ----------------------
oSIST ISO 6003:2018
INTERNATIONAL ISO
STANDARD 6003
Third edition
2017-11
Alpine skis — Determination of
mass and polar moment of inertia —
Laboratory measurement method
Skis alpins — Détermination de la masse et du moment d'inertie
polaire — Méthode de mesurage en laboratoire
Reference number
ISO 6003:2017(E)
ISO 2017
---------------------- Page: 3 ----------------------
oSIST ISO 6003:2018
ISO 6003:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST ISO 6003:2018
ISO 6003:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Apparatus ..................................................................................................................................................................................................................... 1

5 Sampling and conditioning ........................................................................................................................................................................ 2

6 Calibration of measuring device .......................................................................................................................................................... 2

7 Procedure..................................................................................................................................................................................................................... 3

8 Expression of results ........................................................................................................................................................................................ 4

8.1 Mass of the ski ......................................................................................................................................................................................... 4

8.2 Polar moment of inertia of the ski .......................................................................................................................................... 4

9 Tolerances ................................................................................................................................................................................................................... 6

9.1 Measurement tolerances ................................................................................................................................................................ 6

9.2 Tolerances on published data .................................................................................................................................................... 6

10 Test report ................................................................................................................................................................................................................... 6

© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST ISO 6003:2018
ISO 6003:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This third edition cancels and replaces the second edition (ISO 6003:1984), which has been technically

revised.
iv © ISO 2017 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST ISO 6003:2018
INTERNATIONAL STANDARD ISO 6003:2017(E)
Alpine skis — Determination of mass and polar moment of
inertia — Laboratory measurement method
1 Scope

This document specifies laboratory measurement methods for mass and polar moment of inertia of

alpine skis.

If laboratory measurement data are determined and published by the ski manufacturer or other

institutions, standard measurement procedures can be used
...

SLOVENSKI STANDARD
SIST ISO 6003:2018
01-september-2018
1DGRPHãþD
SIST ISO 6003:1995
$OSVNHVPXþL'RORþHYDQMHPDVHLQSRODUQHJDY]WUDMQRVWQHJDPRPHQWD0HWRGD
]DODERUDWRULMVNRPHUMHQMH
Alpine skis -- Determination of mass and polar moment of inertia -- Laboratory
measurement method

Skis alpins -- Détermination de la masse et du moment d'inertie polaire -- Méthode de

mesurage en laboratoire
Ta slovenski standard je istoveten z: ISO 6003:2017
ICS:
97.220.20 Oprema za zimske športe Winter sports equipment
SIST ISO 6003:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 6003:2018
---------------------- Page: 2 ----------------------
SIST ISO 6003:2018
INTERNATIONAL ISO
STANDARD 6003
Third edition
2017-11
Alpine skis — Determination of
mass and polar moment of inertia —
Laboratory measurement method
Skis alpins — Détermination de la masse et du moment d'inertie
polaire — Méthode de mesurage en laboratoire
Reference number
ISO 6003:2017(E)
ISO 2017
---------------------- Page: 3 ----------------------
SIST ISO 6003:2018
ISO 6003:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 6003:2018
ISO 6003:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Apparatus ..................................................................................................................................................................................................................... 1

5 Sampling and conditioning ........................................................................................................................................................................ 2

6 Calibration of measuring device .......................................................................................................................................................... 2

7 Procedure..................................................................................................................................................................................................................... 3

8 Expression of results ........................................................................................................................................................................................ 4

8.1 Mass of the ski ......................................................................................................................................................................................... 4

8.2 Polar moment of inertia of the ski .......................................................................................................................................... 4

9 Tolerances ................................................................................................................................................................................................................... 6

9.1 Measurement tolerances ................................................................................................................................................................ 6

9.2 Tolerances on published data .................................................................................................................................................... 6

10 Test report ................................................................................................................................................................................................................... 6

© ISO 2017 – All rights reserved iii
---------------------- Page: 5 ----------------------
SIST ISO 6003:2018
ISO 6003:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following

URL: www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 83, Sports and other recreational facilities

and equipment, Subcommittee SC 4, Snowsports equipment.

This third edition cancels and replaces the second edition (ISO 6003:1984), which has been technically

revised.
iv © ISO 2017 – All rights reserved
---------------------- Page: 6 ----------------------
SIST ISO 6003:2018
INTERNATIONAL STANDARD ISO 6003:2017(E)
Alpine skis — Determination of mass and polar moment of
inertia — Laboratory measurement method
1 Scope

This document specifies laboratory measurement methods for mass and polar moment of inertia of

alpine skis.

If laboratory measurement data are determined and published by the ski manufacturer or other

institutions, standard measurement proc
...

NORME ISO
INTERNATIONALE 6003
Troisième édition
2017-11
Skis alpins — Détermination de
la masse et du moment d'inertie
polaire — Méthode de mesurage en
laboratoire
Alpine skis — Determination of mass and polar moment of inertia —
Laboratory measurement method
Numéro de référence
ISO 6003:2017(F)
ISO 2017
---------------------- Page: 1 ----------------------
ISO 6003:2017(F)
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2017

Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette

publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,

y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut

être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.

ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Tél.: +41 22 749 01 11
Fax: +41 22 749 09 47
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii © ISO 2017 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 6003:2017(F)
Sommaire Page

Avant-propos ..............................................................................................................................................................................................................................iv

1 Domaine d’application ................................................................................................................................................................................... 1

2 Références normatives ................................................................................................................................................................................... 1

3 Termes et définitions ....................................................................................................................................................................................... 1

4 Appareillage .............................................................................................................................................................................................................. 1

5 Échantillonnage et conditionnement .............................................................................................................................................. 2

6 Étalonnage du dispositif de mesure ................................................................................................................................................. 2

7 Mode opératoire.................................................................................................................................................................................................... 3

8 Expression des résultats............................................................................................................................................................................... 4

8.1 Masse du ski .............................................................................................................................................................................................. 4

8.2 Moment d’inertie polaire du ski ............................................................................................................................................... 4

9 Tolérances ................................................................................................................................................................................................................... 6

9.1 Tolérances sur les mesures .......................................................................................................................................................... 6

9.2 Tolérances sur les valeurs publiées ...................................................................................................................................... 6

10 Rapport d’essai ....................................................................................................................................................................................................... 6

© ISO 2017 – Tous droits réservés iii
---------------------- Page: 3 ----------------------
ISO 6003:2017(F)
Avant-propos

L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes

nationaux de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est

en général confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude

a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,

gouvernementales et non gouvernementales, en liaison avec l’ISO participent également aux travaux.

L’ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui

concerne la normalisation électrotechnique.

Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont

décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier de prendre note des différents

critères d’approbation requis pour les différents types de documents ISO. Le présent document a été

rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www

.iso .org/ directives).

L’attention est attirée sur le fait que certains des éléments du présent document peuvent faire l’objet de

droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable

de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant

les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de

l’élaboration du document sont indiqués dans l’Introduction et/ou dans la liste des déclarations de

brevets reçues par l’ISO (voir www .iso .org/ brevets).

Les appellations commerciales éventuellement mentionnées dans le présent document sont données

pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un

engagement.

Pour une explication de la nature volontaire des normes, la signification des termes et expressions

spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion

de l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles

techniques au commerce (OTC), voir le lien suivant: www .iso .org/ iso/ fr/ avant -propos .html.

Le présent document a été élaboré par le comité technique ISO/TC 83, Matériel et équipements de sports

et autres activités de loisirs, sous-comité SC 4, Équipements de sport de neige.

Cette troisième édition annule et remplace la deuxième édition (ISO 6003:1984), qui a fait l’objet d’une

révision technique.
iv © ISO 2017 – Tous droits réservés
---------------------- Page: 4 ----------------------
NORME INTERNATIONALE ISO 6003:2017(F)
Skis alpins — Détermination de la masse et du moment
d'inertie polaire — Méthode de mesurage en laboratoire
1 Domaine d’application

Le présent document spécifie des méthodes de mesure en laboratoire de la masse et du moment

d’inertie polaire des skis alpins.

Si des résultats de mesure sont obtenus en laboratoire et publiés par le fabricant de skis ou tout autre

organisme, des modes opératoires de mesure normalisés peuvent être utilisés pour s’assurer que les

résultats soient comparables.

Le présent document spécifie également une plage de tolérance dans laquelle peuvent se situer les

résultats de mesure obtenus sur tous les skis fabriqués si, pour les modèles concernés, les résultats de

mesure de la longueur sont publiés par le fabricant des skis.

NOTE La longueur appropriée des skis peut être fournie avec les résultats de mesure publiés.

Le présent document n’a pas pour but d’évaluer l’incidence des résultats de mesure sur la qualité du ski.

2 Références normatives
Le présent document ne contient aucune référence normative.
3 Termes et définiti
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.